Відео

thanks!

Amazon Gauge wins 😊

Thank you!! My bin had the exact same problem and I managed to fix it using your method. Simple Human don't sell the replacement pedal section... can't imagine why 😂

Just fixed two of my newly installed heads by doing this... he's not kidding when he says don't take too much grease out, I took enough to cover the blade of my screwdriver out and it made a big difference. Less is more, I would say.

I think it’s non hardening silicone, not grease.

thank you for this video! Also fyi I found that the step cans have a 10 year warranty. I had the same issue and customer service was awesome!

Than you for this video. I had the exact same symptoms, followed your video and discovered exact same cause of issue. I did similar fix using plastic welder gun using hot nails.

Wow! Excellent video. Thank you!!

Thanks for the video. There is way easier way to open it. No need to use screwdriver. Remove the filter then rest the bottom to some hard and stable surface and then push down only blue part with your fingers. The middle black part will come off.

I tried this and it worked. saved a few bucks

this worked like a charm. thanks so much for posting this!

No idea what’s wrong with mine but it’s similar to this. I’ve taken it all apart and can’t figure it out. The bar works when I push it by hand, but once I put the trash can down and try the foot pedal… nothing. It doesn’t budge. But if I lift the lid and then push the pedal, it stops the lid from going down. It just won’t push it up at all. 🤷🏻‍♀️ I’m about to take it apart again and double-check for cracks. It’s all I can think of! Thank you for this! Especially for the soldering part - I never would’ve thought of that and I have one in my closet!

Finally, this method worked for me, thanks :) I fixed 3 heads today, and all of them looks good. I was tired that even new heads can stop rotating after a year.. (some is okay for years, not sure whats causing it)

Thank you!!!

Do you know roughly how long it should stay 'fixed' for before you have to redistribute the grease again?

Trash cans that are trash. Sis bought one and it doesn't work anymore I'm sure it has this issue too.

Thank you so much

Wow! No matter how obscure or specific a problem is, there is always an answer on the Internet,! My trashcan exhibited the same exact behavior, and had hairline cracks in the same exact places as in this video. Thank you so much for the video! It really was perfect!

Great video thanks for explanation and showing tools. I have a older different model but this video helps immensely with repairing.

Thanks, but no way could I do this but kudos to those who can. My trash can is the "open can" voice command type and it is only opening 3/4 of the way. I can unplug it, put my hand over the sensor wait 2 min then plug back in and it works! Unfortunately minutes to an hour later it is back to not opening up all the way.

Im experiencing the same problem but have the double sided can with the recycling bin, I’ll have to do some more troubleshooting to find out why the lid isn’t opening properly.

Note: Some of the recent model have removed the screw at the pedal! You now can't look inside to figure out the cause of the lid not opening properly...

That’s not where mine failed.

Just saved my life. You deserve an honorary member of greatness award, distributed by the United Nations specifically for the greatest human achievements ever considered slightly possible. You are number one 100%

Part ### number have the same problem with my compressor. I will appreciate your help...

Worked like a champ! Many thanks for the straight forward instructions and not leaving anything out.

thanks fhis fixed mine too

This is the one! Thanks.

Promo sm ✨

Dude these heads are like $6. Just buy a replacement.

You're an angel, thank you!

he didnt show how he removed the old switch he said how but didnt demonstrate ugh smh not helpful at all👎

Somebody has to know what grease that is… Have you found out yet? Thanks for the video.

I wonder if that's damping grease they used. It's used in volume knobs and tripod heads to give a smooth and slow action.

Is there a number on the switch ? I can't read the one I have.

This help me a lot and save my parents money to not have to hire company to come out and do it. They would’ve had to wait two months because it’s summer.

I wonder if pool lube would work. I have a half dozen of these that don't seem to rotate properly. I tried this and it took less than 5 min from start to finish. It's didn't work at first, but I manually spun it and it started spinning. I'll have to try these on a few other heads. I used a tooth pick to distribute the grease. Thanks!!

I like the idea im just opposed to spending that much time and and contract with a portapotty.

Try the golden gate Bridge technique: just shit wherever you want

Weeeeeeeeeeeeeeeeeeeeeeeeeeeeeee ‼️ ⚠️ ❕ 🤯 👀

Bro you put your bare ass on the toilet seat?

Un My case it's spinning too fast. Do You know what could be done un order to have a lower movement?

Followed the instructions and it worked brilliantly! Thanks a lot!!

These things are 5-6 bucks. Not worth the trouble. IMO.

ty great help

the video starts with the unit already apart? this isn't "disassembly", but rather "disassembled"...

Thanks

How the reassembled ones working?