Відео

Great video . I have a 455 and it fires up but just bogs out and dies . I have done a carb kit and fuel line and tried tuning but it's still not right . But now ready to open it up again

8i0opp8⁸oppòiiiiìklkkkljjù

But why do they fail? How can it be prevented?

3 mins and the first part on the camshat is dohickey thing

Monster ✌️✌️✌️✌️✌️

After watching 7 or 8 different ones on cam shafts , You have given me all the relevant information that I needed,Thanking you for the advice and information,100 %,

No clue who you are but I just did a cam job on mine and this helped tremendously. My first cam ever: thank you

What size crank shaft outer diameter does a 25 horse Briggs and Stratton have

Io ciò il modello più piccolo il 500

One question if the dots don't line up what do u do in details please so they line up thank you

Very good Video thmk you ❤

I believe it can be 280 out.. the crank turns 2 time to the cam, doesn't it?

Great lookin' S10. She's runnin' good and she sounds awesome!

Great video

Nekem ugyan ijen van.eredeti.eladó

Measuring squish😅?

I have learned from this video

You made the best video Sir, even down to a close up of the governor position. 5 stars sir!! Thank you.

This guy is a fucking Racist a complete piece of shit he literal sits on peoples pages with hate in his heart trying to bring down other people to gain some type of clout 😂😂😂😂 his a disappointment as a human being

It can be fitted 180⁰ out

Briggs n Stratton Engines are junk, Ever since the over head Valves come out!!!

Never occurred to me that Holzfforma Chains was made in Germany, I was thinking China....

Thanks for your time!! That’s exactly what happened to my engine!!’ But I wonder , I noticed on the governor, one tooth looked a Little chipped!! I hope it’s alright!!! Any tips?? Thanks again for your help and patience!!!

I'd like to add my compliment as well regarding the clarity of this video. I have watched several others and they were not as exact on the critical method of timing. Thank you!

Probably the best camshaft replacement video on a Briggs on UA-cam. Simple explanation, clear audio, clean video...just got REALLT confused when I heard your voice for a minute because I've been watching McGregor highlights this morning! 😳

Pretty Cool And an Original Orange Stripe Bar From The 70’s 😀😮😀

Just make sure you get all the peace out, use a magnet to help you and clean it good

What position is the piston in . Tdc

If you have a oil filter on your motor, make sure you get the right cam. With oil filter,the camshaft will have a slot on the end. The one without oil filter,the camshaft will not have a slot. And as far as removing the pulley off the crankshaft? You may come across a stuck pulley. Then you have too heat the crankshaft.....Good luck.

The camshaft rotates once for every 2 rotations of the crankshaft. Therefore it’s possible to have the dots lined up but for the camshaft to be 180 degrees out. If like me you are unfortunate enough to have moved the crankshaft inadvertently while the camshaft is removed the solution (assuming you have tried to start the engine without success and much backfiring) is to line up the dots, then lift the camshaft and turn it as close to 180 degrees as you can, then turn the crankshaft until the dots are aligned or close to alignment. If they are out by a couple of teeth simply move the camshaft round a couple of teeth until they mesh, the timing is then correct. I found out the hard way through my ignorance.

what is the part number

Where are the cam followers when you were putting in the new camshaft?

If you use the mower intermittently , just take off the air filter , cover the pipe completely to cut off the air , get it spinning , pull your hand off & it will fire right up !! Been doing this for years on a 19hp Gold Series engine !!

I can also agree with the impact screwdrivers. As a bricklayer I screw so many wall anchors and this product does the job great and with ease. Sure its not as good or strong as many other brands but does the job great. Today i bolted 8mm screws all day long. About 800-900. With the big 8ah battery. The battery was not even half empty. The driver do not overheat and is great for the cost. I will buy the black version too when I found It.

Another alternative if you have the tools. ua-cam.com/video/hFaxIl_rDg4/v-deo.html

Excellent! Thank you very much.

Probably should install the push rod tappets first.

Good video, good information and to the point. Also, you forgot to put the tappets in. Hope you realized that before you put it together! Keep up the good work!

Where's the lifters??

Sweet

17.5 engine

😁👍☕

Well I saw that you didn’t clean everything out, when you put in the shaft there was a piece of spring laying in there.

Anybody know if and where you can find a cam with larger lobes for a briggs and stratton 14.5 i/c quiet, possibly valve springs too and maybe a lighter flywheel?

Ehhh... I am going to try this....you make it look simple...

Excellent video. Right to the point with zero fluff. Perfect!

Nice vid :) For those attempting this, this engine doesn't have an oil pump. Note lack of oil filter and access cover on the sump cover. But for those that do there are a couple extra steps. This guy does a good job of explaining those steps though i'm not really a fan of his presentation. You'll see lol. ua-cam.com/video/dWHPHGZAvj4/v-deo.html

Fantastic Video, right to the point. Can't thank you enough for posting it. I now have a clear understanding of the job ahead of me. I'm going for it !!!!!

This guy does really god,clear and very informative videos.

Poor saw ain't happy. Gotta tune that thing correctly.