Відео

You replace the oil from the top, under the air box. Where he’s adding the oil is simply to know when it’s full..it will begin to run out when its full.

Does it require an injector pully to remove?

Thank you very much.

Thank you for the part number! I was needing that! Is that for a 2011 x5 35d? That’s what I’m working on. 😀

I’m having a hard time finding the exact injectors to buy. Can you refer me to a supplier? Online. I’m in the USA if it matters. Thank you.

Thank you!

Thanks man! I have no owners manual, that was driving me nuts.

Normal is 180 kOm +-10

who else modified the plastic clip so you never have to do that again?!?!?!

Man i dont know how long i pulled on that stupid strap.that is HOOKED TO NOTHING..

Tried for 2 hours, almost broke both my wrists, gotta be a tool for this! I just used a 3ft pry bar and it popped right off and didn't break the tabs - set the pry bar on top of the baby seat attachment and popup, place something under after it comes off so it doesn't lock again.

Mine is 2011 I think so it should be like this one I hope..im going to try today

HUGE help...Respect from Baltimore

injectors must be coded in to ecu

is it possible to put injector brackets back to front

Should be 2 quarts guys. Redline GL4 is recommended but a little pricey

Thank you 👍

Very helpful thank you

Hello. I'm changing rocker cover gasket on a 2006 X3 diesel and I'm trying to get injectors out but a few studs are giving me trouble the single Hex 4 mm socket has stripped the stud head I got several of them out but can't get the stuck ones out to remove the rocker cover any advice would be appreciated

Excellent information this

thanks big help :)

فدوة اني عندي x5 2008 ديزل تدير بس ما تشتغل

Thank you!!!!🙂

👏👏👏👏👏👏

Crazy how there is 13min video out there explaining to do this same thing.

Awesome thanks!

Do you use torque+spanner?

I laughed when you’d directed your annoyance at a bolt saying he’s a trouble maker. 😂 As a mobile mechanic I have to do an injector today on a 2007 x7 3.0 litre. It stalls when driving. Customer has unplugged cylinder 5 injector and been driving it around perfectly fine like that. Sounded ok and revved ok to be fair. ECU did not put it in limp mode so all good. I noticed yesterday something never seen before. Battery able to crank the car normal after 5 minutes dropped from 12.3 volts to 6volts. Also weak jump pack on under bonnet jump connectors the engine would not crank. Taking it to the battery terminals instead, instantly it would crank. Less voltage drop clearly. Stupid to put under bonnet terminals for battery when they put the battery in the boot. Thats for saying injector resistance is between 200/300

It’s just that easy huh? I need more room for a speaker box. This will work perfectly. Thanks

I have a 2010 accent 5 speed manual and needed this bad! THANK YOU BROTHER!

Thank you.

LOL, (at 10 sec ) i didn't pull the intake out, of course the last connector in the back controlling the flapper is a B@#$% to remove, i her you, but it worth removing to clean the inlet as it gets extremely dirty, good job keep it up

Has this transmission fluid oil filter?

Thank you my man. very helpful

@autowpg1 I found the resistance needs to be 180ohms for a good injector? Can you explain where you got 200-300ohms from?

Hallo from South Africa I get a code from #5 injector saying positive short to negative sometimes not always. Can it be repaired perhaps? I can drive for days before engine stalls. Can it be wiring? Regards Theo

Good video to locate the plugs but there are some tips To Measure the oil The plug nut for filling… take off the air filter at the top and you will find the plug And after you drain the oil and put the nut back… open the measure nut on the said to make sure you put the right amount of oil when the oil come out and let it drop out little bit and after you done that tight all nuts and start your car until warm up than do something very important Put the gear on R for 10 Second or 15 and repeat that with N -D 1-2 and back This step to fill all the empty spots in the transmission than drive the car slowly up to 40 km for about 10-15 minutes Good to goooo 😊

omg my dude, i am trying to do this myself too! i bought a door handle with the button, and i am about to buy just the harness cable that connects to that door handle, where does that harness connect to? is there anyway you could show me brother? i would really appreciate it, i am burning up, i cant find answers anywhere :'c

Any reprogramming necessary to install the replacement airbag, obtained used from salvage vehicle? Also any info out there on replacing the passenger side airbag? Thanks!

What ares symptomes of bad clutch

Спасибо)

did you say we dont need to reprogram or recode our ecu?

Здравствуй у меня е70 35d и тоже иногда глохнет на ходу ошибок нету мерил сопротивление форсунок и все одинаково показывает около 178ом мотор работает отлично что можно ещё проверить? Спасибо

How do you check the resistance in the injectors? I have an E53 and diagnostics marked errors on 3, 4 and 5. Thanks man

Hi sir and have the same problem with my x5 e70 2007 model and did change glow plugs but still it cut while driving so do I have to do the injectors plz help

likes

Injoctor voltag

What about the seat part?

Omg ty man

Is your $700 bucks include parts and labour?