Відео

Right on

Well done !

Nice flying man!!

Excellent flying well done!

Awesome flying!! Did you leave it in 3D rates the whole flight? So around 100% dual rate and 75% expo?

Yeah, try those maneuvers w/ any other float plane - MAJESTIC😜👍😉 Wonder if the 43” would be tougher to fly w/ floats?

Mine is doing the same thing on my crack laser pro

Would have liked to have seen what you did. I need to have my Carbon Cub handle better on water.

That is insane precision! I just finished mine yesterday, and i am using a slow fly prop on my 3s! What I did was tuned the high end throttle down to 15%.

I'm impressed with your flying skills great job. I just got one of these planes and wanted to see what it's capable of and you definitely show its capabilities 😋😋😋

where did you get it or did you make it?

bad ass man

Cameron. He also recorded another flight (in two halves), in which he makes several disparaging or funny (or both) comments. I might post that one just for the fun of it.:p

lots of smily faces :D :D :D

Thanks.

Good job

lol i would not want my hand to get cut off :P :P :P

I have had the same problem with 4 different servos from Twisted Hobbys. The crappy thing is they won't do anything about it after it has been installed. They tested fine before installation and after installation they freaked out. In fact I have one that that doesn't have and end left or right and wanted to go all the way around. I uploaded a video after I had to cut it out of a brand new airplane.

Yup.:) I'm running a bit less aggressive prop now, hopefully the motor will hold up.:o

finally got the motor back?

Thanks. I never measure my CG, I just put the battery in the middle of the tray, fly and adjust to my liking. I think the CG ended up at the back of the wing tube.

Very nice flying, may I ask where you have your center of gravity?

Thanks.

Nice one Eagle.... maximus2975

I love it! The MXS-C is really tough. I've had countless midairs, one with a 78" glow plane! (That's why the nose is rebuilt with balsa.)If you buy one, get the Twisted Digital Power Combo. The Twisted Digital servos are awesome, and the 26g Crack Series motor has tons of power.

nice! So how do u like this plane? I am looking at buying the crack yak lite. Does it hold up well in crashes?

Hello, what for a accu?

Thanks. I know about the "low wing gets rudder" for torque rolling, I just can't remember to use it when a last-minute emergency rudder correction is needed.:p

I believe I was using a Hyperion 2S 330mAh battery for this flight. WAY more power than the Eflite batts.:)

Are you using the 2s 200ma battery? I see you got it to hover. Thats great

Great Flying Nitro! You make flying in small spaces look easy lol! A trick I use to help with rudder (belly facing in hover & torque rolls), watch the low wing. Rudder to the low wing side to get the nose back up. Amazing flying Nitro! ---Dee

Thanks. The weather here has been HOT. 'whew'

It already is FPV. It's ~awesome~

great :D cant wait to see some footage of it. also, if it is not already, you should set it up for FPV :D :D :D

We fixed it.:) I just had to recalibrate two of the ESCs.

I'd check connections, maybe resolder and make sure everything's wired up right. Might also want to flash the ESCs with BLHeli. (Superior ESC firmware in any situation- as long as your ESCs can be programmed with it) LHS might be able to help if none of that works- and if all else fails you might just have to get a new set of ESCs. If you do have to go that route I highly recommend emax BLHeli: www.emaxmodel.com/esc/blheli-series-esc.html

Looks like an ESC issue to me. What ESCs? If possible, reflash them with BLHeli or whatever firmware they can run. Then, try re-calibrating the ESC on the TX by hooking it directly to the throttle on a RX. Then, plug it in with the throttle FULLY UP, this should tell it where to set your high throttle endpoint. Then, lower the stick, and that will tell it where to set the low endpoint. Unplug, and hook it all back up again. If it still doesn't work, then it may be a FC issue instead.

Thanks. Except for the landing.:p

Geez you're a good pilot... nice flying!

Yes.:) Each of the Capacitors on the end of the ESC had a broken solder joint. Once I resoldered them, everything worked fine.:)

Did you figure it out? Mine does the same

Thanks. I did cut a little grass the times I landed unexpectedly.:p

Almost mowed the lawn a few times- nice!

Thanks. Nice.... I kind of want to get an AS3Xtra. I could fly it in our barn..... I just turned 15.:)

Thanks.:)

Great flying!

She's doing fine, a little beat-up. Except that the aileron servo just died.:(

Thanks. You're gonna' love float flying!

No.:p I had been trying to get Somethin' Extra (on RCG:www.rcgroups.com/forums/member.php?u=476011) to get the MXS-C. He used to have a Twisted Hobbys Mini Crack Yak: www.twistedhobbys.com/TH-24-EPP-Mini-Crack-Yak-55-RCF-24-Mini-Crack-Yak-55.htm I posted this video to show him the great knife edge spins the MXS-C does. :)

3:17 was that a remark about my yak?