- 52
- 817 036
williamclark77
United States
Приєднався 10 сер 2006
Відео
CNC Machining Brass with Some Thread Milling
Переглядів 1,7 тис.5 років тому
CNC Machining Brass with Some Thread Milling
Tormach 3d Machining ABS and UHMW
Переглядів 5135 років тому
What the title says. Just quick cell phone clips. The 1/2" flat HSS endmill was 5100 RPM, 75 IPM, .1" stepover, and 1" DOC. The 1/2" carbide ball endmill was 5100 RPM and 90 IPM.
3D Machining UHMW With a Tormach
Переглядів 4,7 тис.5 років тому
Some parts are sped up. The sound should give it away. The 3/8" end mill was ran at 5100 rpm, 90 ipm, .125 stepover, with a .5 doc. It had 2" of stickout. The 1/2" ball nose was ran at 110 ipm, .02" stepover one way and .01" stepover the opposite direction to finish.
Increase Tormach PathPilot Rapid Speeds
Переглядів 1,6 тис.6 років тому
Use at your own risk! Don't blame me if editing your configuring causes machine issues, fires, or genital warts.
Quick 4th Axis Demonstration. 3+1 Positioning.
Переглядів 797 років тому
A short clip showing 4th axis positioning. It's actually 3 1 and not continuous 4th axis. I don't own any software that's capable… yet.
CNC Drilling and Tapping 316L Stainless on a Tormach 1100
Переглядів 1,2 тис.7 років тому
CNC Drilling and Tapping 316L Stainless on a Tormach 1100
3d Machining Custom Bearing Caps on a Tormach 1100
Переглядів 6 тис.7 років тому
3d Machining Custom Bearing Caps on a Tormach 1100
Hub City 7 22 17 2
Переглядів 1217 років тому
The second time trial run at Hub City on 7-22-17. The fuel pump belt broke right off of the line.
Tramming the Tormach PCNC1100
Переглядів 1,7 тис.7 років тому
Quick video showing how I trammed mine. After leveling the stand (I say bed in the video, I meant stand) it was still .009" in X and .005" in Y out over a 9" space. You also need to jog the Y axis to check it. I only jog the X in the video.
CNC Machining a Bridgeport Knee Nut
Переглядів 3128 років тому
Making a nut to drive the knee of my Bridgeport mill with a power drill on my homemade CNC machine.
Canon 70d Video Autofocus in Low Light
Переглядів 8 тис.11 років тому
Canon 70d Video Autofocus in Low Light
King Motor T1000 SS with Bug Body and Zen G29RC Bashing
Переглядів 2,7 тис.13 років тому
King Motor T1000 SS with Bug Body and Zen G29RC Bashing
King Motor 5t T1000 SS Dirt Pit Fun
Переглядів 3,7 тис.13 років тому
King Motor 5t T1000 SS Dirt Pit Fun
2024.2023
2024
What sort of 3/8" end mill is that? Such as flute count, straight or up/down spiral? Part looks fantastic, nice finish! I'm getting quite a bit of chattering even with a finish pass, so my chip load is probably incorrect.
Just a regular 4 flute for steel. It was new and sharp. They MUST be sharp. They won't cut cleanly on this UHMW or ABS without a really sharp edge. This was one from Tormach I ordered. I just pulled the cut file. That was at 5100rpm, .14" radial,. 5" axial, and 50ipm for about .005" feed per tooth. It was finished with a 1/2" four flute ball endmill at 5100rpm, 90ipm, and .02" step over. I use mist coolant. I was getting melting/sticking dry. Must be a pretty rigid setup or it'll flex the material. That was my biggest issue finishing. These are armrests for a power wheelchair. I made several. The final finish was very smooth to the touch once I figured it out.
Oh, the endmills were all regular 30 degree. Some of the 3/8" endmil roughingl was at 75ipm for .0073ipt. I can't remember what it was in the video.
@@williamclark77 Awesome thank you for this information! I will try some of these feeds/speeds out! I have a 1/4" plastic cutting o-flute for UHMW profile cutting, but it's coated so maybe my polished/non-coated aluminum cutting end mill will work better.
@@alabaska182 Good luck with it. Once I finally quit being scared to send it I got much better results and less overheating the material. I never tried any fancy specialty endmills. None of the oddball material projects I get are high enough in quantity to justify it. One of the worst I had was some ROUND parts from 101 copper with weird features and a deep 7/16-20 tapped hole in a thin wall.
Ive only had my rovan for a little over a week havent even run the first tank havent had time!!!! Buut if i had on complaint it wiuld be the rear wheel hubs theyres akot of play between the inner shaft and where sleeve and hub seat... atleast on my model .other then that its done exactly as its supposed to . Prime pull and off i go no need for choke or anything 😊.. heres hoping i havent jinxed myself
Sounds great! I hope you didn't jinx yourself and that it lasts you a long time!
@@williamclark77 thanks mate I appreciate it ,😁🤜🤛
Those gear shifts are bloodt violent. I love it haha😅
Thanks for sharing! The # at the beginning of the line for 200 inches per minute comments out that line. This change has no effect on the machine, as commented out lines aren't read.
Thanks for the reply. Their updates have changed the process a little bit.
Are you insane or dumb?! That is the only freaking thing you are not supposed to do! How to is that professionalism?! Go learn how to take care of a snake before having one and stop being an idiot!!!!!!!!!!!!
I don't know why I read 7 years of comments in reverse chronological order (out of a possible 11 give or take). I don't know what to take away from the experience. I don't know how to refer to the defective nature of the people repeatedly commenting the same asinine thing. What is it about this video that makes them all trip up at the same low hurdle? It's late in the game, but I think the video title could be amended, somehow, to alleviate the trap that people keep falling into. I think just adding "(Intentionally Wrong)" at the end of the existing title might attenuate the doltish commenting. Just a thought. Maybe it's more interesting if it goes on forever.
That could be a good idea. The comments come in waves it seems. Months with no comments then bombarded with many per day. I guess whenever it gets shared or makes its round in the algorithm.
Still got this beauty ? Would love an update
Oh yeah. I'll never part with her. She's still doing great. I use her a few times a year to take to elementary schools and introduce them to snakes and educate. She's never so much as hissed in defense, even when touched by excited 8 year olds. Still feeds like she's insane though! And no, I haven't hand fed like in this video since. I only did then for a specific reason.
That took amazing patience.
Check my channel ua-cam.com/channels/18rb7n8HgSNXGXbovcKu7g.html
Yo did it on purpose for clout
Negative
Está amaciando?
I only speak English
Did you learn how to reply to comments yet?
Nope
@@williamclark77 liar
@@bovice1766 How observant thou are!
Amateur hour!
More like amateur 20 minutes
What’s dumber than once? Twice! Lol idiot
Commitment!
Sir please show me your ways
Much better than 3d printing
A whole lot more mess though! I hope to build a 3d printer large enough for things like this one day.
Excellent job
Why would you do that? Really not cool video.
Read the description and any of the 1300 or so comments. It wasn't to be cute or cool. It was to show some people on a forum what would eventually happen if they continued to feed by hand, and if they still chose to, how to handle it when they did get bit.
Gonna do this tomorrow! thanks. Why did you choose 120ipm for Z?
I believe the places you must modify are in a little different location now since some updates. I didn't try going faster on Z to avoid damage. It may could handle faster. I haven't tried.
Dumb ass . I realize u did this on purpose but really .. let’s see how long I can stress out my snake ...
She was perfectly ok and still ate. So, she wasn't stressed. This video is about ten years old. She's still around doing great.
Cut your nails lmaoo
Ok, but then will you scratch my butt?
What a fing mess, I hope 3d printers can get better and produce similar results without all the waste in reasonable time.
That will be nice. These could be 3d printed if you had a large enough printer. Mine is not that big!
Way to stress it out dumbass
Because they always eat when stressed!
Dont defend yourself. You know damn well this is a stupid amateur move that can potentially harm the animal. Lets just hope your smarter than you were 9 years ago.
@@sebl9710 Read the title of the video, the description, or a few of the thousands of comments.
Don't they have the longest teeth??
Compared to their body size they have some of the longest. Adult retics, burms, etc have teeth that are larger. Just not as large compared to their size.
Mr. Clark. If I may ask, was the hand paralyzed at some point prior to the video?
Yep. Spinal cord injury. Motocross.
@@williamclark77 I recognized the posture of your hand and the lack of response when it actually grabbed you. 😀
@@StLMikie Normal feeling. Little motor control. At least it didn't start clonis shaking and hurt her. I was worried about that.
Jokes on y’all, that’s not even a real hand lmao
I knew it would happen eventually.
He got ma fanger 👨🌾
Keep mouthwash with alcohol in it in a little spray bottle and spray their mouth if they won't let go. Works every time with little to no harm to the animal.
Yep. Plain water from a spray bottle will usually work too. I didn't want to do anything to her and let her do her own thing since it was 100% my fault. I knew it would happen eventually.
@@williamclark77 I had a retic latched on and didn't let go for 15 min. It's a last resort that works 100% of the time.
@@stuntmanbillyslots Scary! I don't raise the big guys any more. I had burms, but thank goodness, never had a real bite from an adult. Juvies and hatchlings don't count. I always kept a spritzer bottle on their setups just in case.
Thank you so much for this, I was having a problem with my Y axis stalling and I lowered the speeds and it doesn't stall anymore.
Was it stalling at the stock servo settings? If so, I would think you have a hardware issue such bent gib, too tight gib, trash in the dovetails, etc.
Tongues stupid
Description stupid
Cut your nails
Yo sell him to me I won't get bit 😅
She will never be sold!
hahahahah damnit man xD FOR SURE it hurt but it seems that you did it on propuse no ?
Not on purpose but I knew it would happen eventually. So, I was prepared and didn't jerk away. It's no big deal if you don't panick and snatch back. That will hurt worse and likely hurt the snake pretty bad.
Hey There, thanks for the info, Iearned a few things. Suggestions for Version 2.4.3?---Different enough that none of the commentors suggestions worked. I am eagerly waiting the servo upgrade--300IPM. That going to be way better. www.AndersonPrototypes.com
I haven't done the most recent update yet. Haven't had a chance to down the machine long enough and fool with the new ini files. Hopefully they didn't make it basically impossible. The updates used to not break it, just copy the file after updating. It seems it got more difficult each time after I posted this video. I hope I'm not why.
@@williamclark77 Thanks. Hopefully you wiz right thru it. Please keep me in the loop. Jim
Anybody Crack 2.4.3 yet? AndersonPrototypes@gmail.com
@@AndersonPrototypes I still haven't updated. Been too busy, which is good I guess. I plan to every weekend but too many projects to down the machine.
I love it when people try and 'show off' with snakes but fail miserably I've seen it loads
It wasn't showing off. I knew it would happen eventually and why I was recording. Tongs are absolutely necessary!
lol 3am rite now and just come across this funny shit
We all make bad decisions from time to time.
@@williamclark77 yeah facts facts
H
I
williamclark77 l
@@Imperial_Wing J
williamclark77 nooo u supposed to say O because I sayed l and it would be lol
@@Imperial_Wing M
I have the t1000a not a single promble with it first two tanks did a hot an cool down an ever since no prombles knock on wood
Awesome! They were hit and miss. I had five or so of their different models. One great, then the next nothing but problems out of the box. I only have one now and haven't fired it up in several years.
I have the same mill and after seeing your website, I'm now considering converting mine to CNC as well. Knowing what you know now, is there anything you would like to do different with the build? Thanks in advance.
Not much with the cnc conversion itself. It came out really well. I wish I had taken time to remachine and scrape the table dovetails. It had a lot of wear near the middle of the travel that crippled its performance.
I really like how you learned nothing after being bitten and still held the mouse the exact same way you did the first time you got bit. I mean. Holy fuck.
If I were you, I’d probably use tongs
I replied to the wrong comment, sorry. I do use tongs on most of them most of the time. You're absolutely correct.
Where did you order this from
I bought it local. You could order them from a dozen places by searching "Coolster atv" a few years ago. I have no idea now.
Dingo just named this snake as the worst bite teeth wise can do from a snake, took that shit well but I'm pretty positive this wasn't your first rodeo
Nevermind that was a boa
These do have pretty nasty teeth. Fortunately, they're very sharp like needles. As long as you remain calm and don't jerk away, the bites aren't bad, for you or the snake.
Have you figured out how to do this on the new pathpilot 2.4 software? They changed the ini file to not have the speeds listed anymore.
ETA... just found it. They changed the speeds into a different file named tormach_mill_base.ini
I haven't updated to 2.4 yet. I planned to in a few weeks when I had time to down the machine and play with it. I figured they would eventually do an update to make doing this more difficult, especially after the new faster machines came out.
@@bigdog200399 Actually, 2.4.3, this doesn't work with. Its different, no IPM, its something else. Let me know when you update please. Jim
I’m 9 years late but your baby is so cute and I hope they are still going strong such a cute baby
She's still doing great! I take her and one other to elementary schools to educate children. Still super docile with a crazy food drive.
U idiot
Thank you for your astute observation.
Haha no problem
Lemme just hand this snake a mouse we dont dangle around here
Nothing dangles here. I blame the cold weather.
She gave me anxiety when she went and stopped lol
She gives me anxiety all the time!