Відео

I have not tried out the 4uad or TruHop buckings as of yet. Currently, been busy 3D printing some custom housings to test nozzle lengths. Curious if best for nozzle to push the bb all the way to the mound, or aim for barely long enough to seal the bucking lips.

Tried that today with the max model, adding and removing shims, seems to be that if the nozzle enters too much, it gives fps inaccuracy… currently using 3 0.1mm shims

So far, the biggest improvement we saw was with Silent Alpha and Wolverine Phoenix hopups that slow down the bb entering the bucking (similar idea to Madbull Red bucking design). However, Fish's Kythera is folding in the bucking lips and jamming the bb rather frequently, so focusing on diagnosing that to get him back on the field.

@ have heard pretty good things about the alpha hop ups, what fps deviation where you getting. Currently debating if I should try that one or a M4G with gbb bucking..

With a wolverine Inferno Gen 2, fps is rock solid. I guess my other tip is to run as heavy of a bb as possible. The harder the mound can pinch the bb, the better consistency.

@seb0966 I plan to try .46g at 1.85J with the SR25 at the next Bing Field event I can attend. I used to avoid since the field required .46g are a dark gray, hard to track, but seems my SHP7 requires the super heavies.

@@Karrottop009 grey is no good for airsoft ^^

@NerdESO We're seeing best results with Begadi MHP5 70*, Begadi D3x5mm nub 70 (same as maple leaf omega, but any 70 degree concave nub), and an extra tight tensioner ring (triple groove)

​@@Karrottop009Thanks, will give it a try

It would seem to be the Begadi MHP5 70 degree. The SHP7 only works with .43g and heavier. The Wolverine MTW's nozzle alignment just can't be beat though. Results are phenominal.

These rings are chamber specific. Even if they fit in another chamber, the ring would push the inner barrel forward. Lock clip would not work and would need a super long nozzle. Don't have any footage, but had decent success with Reaps 80 degree bucking in the Kythera with Silent Alpha. Not crazy range, but consistent at least. My Cyma SR25 with the SI Alpha and Begadi SHP7 doing well though.

@@Karrottop009 Interesting, Well what I really want to get working as you might understand is the TNT hop rubber in my kythera build, the rubber lips are "straight" so they dont fit well with the polarstar nozzles, it even leaks air after a few shots, I figured if I can just tighten up the lips and get it to seat the BBs right it would probalbly make for the best setup.

@@scandimanairsoft Well, science never hurts. Don't like it, then you try the next thing lol. For me, this has been the only method to solve the wild innaccuracy of the kythera. Can say that going too tight of a ring has also caused bucking lips to fold into the inner barrel, especially the madbull red apparently.

@@Karrottop009 I acctually have ok accuracy on the kythera with ML MR hop, 50 or 60 degrees, at least in the 1 to the 1.7 joule range. It is when I rock it as DMR up at 2.2 ish joules that I see the flyers, I do think the TNT rubbers would fix it though, I will keep looking for a soution or perhaps ill just get the SI hop unit and try these rings.

Hmm, for me, 1.5J was unplayable with ML, Begadi, Madbull, or Prometheus. Going 1.85J allowed me to lob .40's at least. I also had to use the PTS EPM 250rd's for their super stiff spring to slow down the nozzle. So, what causes midcap syndrome in aeg's is actually helpful for Kythera's super strong nozzle. I also tried a tighter metering screw to slow down the Kythera, but one size change caused double feeding...

Rear sway bar, falken rt660's at 48 front/46 rear are a great combo I find. High pressures keep from driving on the sidewalls with our crappy stock camber. I need to look into brake pads next. Hate how it feels like stock pads are made of wood...

This was a Prommy 6.03 x 500 from the original Freedom DMR build

@@Karrottop009 Excellent, thanks for the speedy reply.

Not gonna lie, our trips out there are a total lottery lmao, but you can spot us on the lot by the RCSB red 15 F150 pulling the quads

Very misleading in size lol

Still working on the Belly of the Beast event, should have that up this weekend

@@Karrottop009 ill make sure i will watch it

Thank ya sir! Hoping it serves just as well as the freedom dmr build!

We're limited to Fish's schedule due to kiddos, so we take what chances we get at this point 😅

I regularly use .40g in my DMR's, .46g in the L96, and .32g in regular m4 builds. 315fps with any weight seems to be a sweet spot. After doing a lot of testing that wasn't uploaded to youtube, I would recommend their SHP7 bucking paired with an inner barrel with extended hopup window. I'm about to upload a video from my new DMR build that uses a combo of .40g bb's, 70 degree SHP7, Begadi Neptun, and EDGi EVO 395mm inner barrel that was stellar for first time out.

What's been done to it because it doesn't sound like it's stock?

@@brianspangler3771 it's stock... all it has is exhaust.. and it gained no horsepower by it...

@@bigsausagepizzamedia4491 Stock tires?

@@brianspangler3771 stock factory radial hard tires

@brianspangler3771 month ago I ran my best with it in stock form. 11.54 @121 in the 1/4 and a 7.49@96mph in the 8th on factory street tires with a full tank of gas

I have a new, Cyma CM098b SR25 build with Begadi SHP7 70 degree in a Begadi Neptun hopup chamber to test next season. Will be using an EDGi EVO 395mm inner barrel to get the volume ratio to about 2.8. Should have videos in the spring if all goes well.

These are .40g bb's manufactured by Tokyo Marui. This field requires that we use their bb's. They have .43g and .46g, but they are darker in color and are difficult to reach past 150ft.

So far, I am only seeing success with 80 degree silicones and 70 degree rubbers. Think there's a minimum force required for the nozzle to position the bb in the same spot every cycle. Also toying with patch shapes, Maple Leaf Super vs MRHop and Begadi MHP vs SHP.

This video was on 3.55's. The 4.10's were installed the same time as the cams. Only video of those 4 runs are in my cam phaser issues video at the 4 minute mark. ua-cam.com/video/bGUdj4fQ4Pw/v-deo.htmlsi=pNdfKivq433uEMDL

I tested their SHP5 bucking last weekend with both my aeg DMR and the HPA DMR, but no footage. The aeg saw great success, but the HPA didn't. Difference was a 6.03 Prommy barrel and 70 degree SHP5 in the aeg vs 6.01 PDI barrel and 60 degree SHP5 in the hpa. Hoping to try a 6.08 Lambda barrel with an 80 degree, silicone MR Hop in the HPA this weekend or the next. Looking to have a Begadi Neptun hopup chamber, SHP7 70 degree, and EDGI 6.01 EVO barrel in the DMR by next spring since barrel was a custom order due to length.

Hero runs Never 112 mph either

Well said!

🤓