- 4
- 174 488
Do it yourself
Netherlands
Приєднався 10 чер 2015
Fm Modulation modification measurement Cybernet PTBM059COX and PTOS006AOX pll board
Cybernet FM modulation Modification mesurement
The modification schematic @ groups/1173501253135443
The modification schematic @ groups/1173501253135443
Переглядів: 97
Відео
Fluke Bussfuse DMM B 44 100 and Fluke 80BK A Type K thermocouple
Переглядів 5 тис.8 років тому
A cheap Ebay Fluke Buss fuse DMM B 44/100 and a Fluke 80BK A type K thermocouple. I found this components on Ebay for a very good price. In this video you can see how i replaced the fuse in my Fluke 179 and how i tested my new thermocouple.
Cruise control repair
Переглядів 88 тис.9 років тому
Hella cruise controls are used by many car manufacturers. Even though the connectors and electronics may be be slighty different, I am sure that the same problems show up and you can do the repair yourself. 5GA 003 828-07 SAAB 85 87 016 Saab 900/9000 year 85-89 5GA 004 397-00 443 907 305 VW Audi 100 200 5GA 004 397-01 443 907 305A Audi 100 5GA 004 397-05 Volvo 3523537 Volvo 240 5GA 004 397-07 S...
Vw Cabrio window regulator replacement/repair
Переглядів 81 тис.9 років тому
Vw Cabrio windows regulator replacement/repair/problem. How to remove and adjust the front power window regulator in a VW Cabrio MK4 (MK3)
I don't understand the part about springs at the relay. There is a relay in my Audi for the cruise control system in the fuse box. What is cleaning springs referring to?
I have one of those Bud I dont bother "to Mosh work, thanks.
These modules are notoriously unreliable. After buying one from eBay and one from a junk yard-both bad. I followed this procedure and resoldered everything on the board except the big IC. Even under extreme magnification, nothing appeared bad, but this fixed it. As another commenter mentioned, I used acetone to removed the coating. Many thanks.
Methyl ethyl ketone will lift the conformal coating like magic, if you can find some.
80BK-A Integrated DMM Temperature Probe can calculate temperature of water heat?
As evident from the video, yes
Top, erg duidelijk en bedankt
Thanks. Just replaced my driver door regulator with this video. Works perfect now.
Where is the modul?
Thanks so much. I followed every step and everything went perfect.
Paint stripper work? Got 2 Audi's that don't work. All I want is leather ,cruise and ac. lol Can't even find the 2001 A8 one.
i would not recomment this. it wont work.
Thanks for the vid my cable broke yesterday I hope I can still get parts here in nz Thanks mark
Thank you so so much for sharing this video. I would suggest people watch it all the way through before starting as the end is extremely important and relevant. I hope you post more tutorials for this car as my next job is replacing the soft top only not the header and there is very little to watch about it. Girls got to do what a girls got to do 🤗 NZ saying 😁
Great video, bit I can't get my window down
Why couldn’t I find this video when I needed to put in a window there’s like little to no videos on cabrios and I hate it
Probably wrong search words? Maybe you can help to update this ?
@@doityourself6558 I’ll try to not sure what I’d do I scoured the internet I always find text tutorials but never videos love my 02 mk3.5 cabby
Hi and thank you for a great video. 17:12 it looks like you should have shown the blue cardboard representing the window the other way round as the right bracket is the rear one (on my car anyway). I can't work out where the fine adjusters stop on the door
It was my right window and it was the best way to show from this side otherwise it would not have been clear. If your parts are the other way around maybe you have the other window?
@@doityourself6558 May I am getting something wrong, it is right windows I am dealing with. Great video regardless, thank you
Is there a datasheet for the 80BK anywhere, so I can see the resistance values? I don't have a Fluke with temperature mode but shouldn't it work too by just measuring resistance?
It makes mV, not Ohm. It is type K.
Ik wil graag mijn raam afstellen van mk4 cabrio, hoe doe ik dat? En waar zijn die stelschroefjes voor?
Als je de video bekijkt dan zie je dat alles wordt uitgelegd.
Excellent tutorial! Thank you. I'm about to pull the CC control board off my newly acquired 99 Cabrio. i'm hoping this is the issue. If not, I see some on ebay for $20.
Thank you SO MUCH for this video. Needed to replace the wing mirror on my parent's Cabrio, I couldn't work out how to get the door panel off at all and couldn't find any videos on how to do it. This video helped so much, thank you for taking the time to make it! :D
Thank you for this helpful video. Huge appreciation to you. Great video. Thanks once again
Do you know if the white wheel at 10:35 is replaceable or how it is attached so that I can try to replace it separately? Thanks in advance.
I don't think it's replaceable. But you could try to use a drill to get the rivet <-- (not sure is its the right name) out. And you could see if you can put a bold in or something else. But better look fist if the steel cable is intact.
Hello, you can see on the video that wires are soldered to the module, as I understand it for checking on the table, can you tell how you connected it.
ahrix novaaaa
You didnt have to pull the speaker out,,i didnt. Just pull the plug from behind.
Acetone worked well enough to remove the conformal coating from my 87 Mercedes cruise control amp.
Oke good to know. Delivery off glychlooretheen is difficult nowadays.
An other good way to refresh the soldering, is to bake the modul in the owen at 300*F for 8 minutes.
Neh not so a good idea. Things will melt on the PCB
Great job! Thank you
Great working. Thank you...
Love the music! Goes great with the slides. Thank you!
Thank You very much for video our window got stuck in the down position and video helped get it back up for a short time. Thanks Again!!
Bedankt voor je handige instructies. We have a 1996 VW Cabrio, and your instructions and video guidance was just what I needed to get this done. We live in Norfolk County in Ontario, Canada, and there are a lot of Dutch people in my church--it was very nice to hear your instructions in English with your Dutch accent. I did pretty much everything that you did, and just finished and the window works great! Thank you especially for the extra details about the clamps and the alignment procedure. Thank you so much.
I love this instruction video, it saved me over $300. The comment I made is about the final adjustments using the star wrenches. I did follow the instructions on installing the unit. I just wanted to see how the fine adjustment using the star sockets to get the final end adjustments. I have viewed the video many many times. The video showing the blue film is very good, but, it does not show the instructions itself
Hey Dale. Your right I didn't film that part. There's only a picture what would be the end result.
thanks for your great Job, i searched for 3 Month now - for a little "How to do" like this The Windows of my MK3 goes just a little bit to high on the back - front to low. I hope now the go up in the sealing again. Thanks a lot
Your very welcome. Hope it worked out for you.
I wish he would show the final adjustments that has to be done to get the window to track correct.
All adjustments are explained in the video
This is a great video, and I intend to try repairing as you explained. But the big question is where in the car this module is located and how to remove it? Thanks.
In my car it was under the dashboard on the driver's side. I had a VW cabrio, possibly that it is different in other cars. But it seems to me that the module must be in the vicinity of the steering column.
I'll check that for sure. Thanks.
Checked. Not there ((
To be honest, mine was deep inside the dashboard. I could not see it till I reached with my hands inside. That's the only thing I can think of. Maybe you can follow the wiring from switch?
Mag ik vragen wat het nieuwe mechanisme gekost heeft bij de dealer ik heb namelijk ook een nieuwe nodig niet aan te komen bij de normale auto onderdelen zaken ....
Het is al weer even terug dat ik het mechanisme heb gekocht, maar meen me te herinneren dat ik iets van 150 Euro er voor heb betaald. (kreeg wel korting) Maar wat heb je precies nodig?
Kwam er maar niet uit waarom het raam scheef bleef staan dankzij deze video toch gelukt top!
Bedankt voor je reactie. Mooi dat het gelukt is
Very helpful; thank you!
Yvw
Can anyone help me with my cruise control settings on a 1995 Pathfinder SE V6 the button is on the left hand side by the power windows when I turn it to on the light goes green the setting acceleration buttons are on my steering wheel when I get up to speed I try to engage the cruise control setting and on my dashboard the cruise control light is on but it is blinking and the cruise does not connect what can I do to fix this so I have cruise control can anyone help me thank you
Can anyone tell me where the cruise control module is mounted in the W203 C200? (2004), thanks for any help.
Mike if its the same cruise control box then it should be somewere under your dashboard. But i am not sure if its used in your car, but it could be its the same.
That was very helpful. Thank you
A simple pencil eraser will clean contacts also. For heavy work, you can put it in your electric drill and spin it. Just a cheap alternative to using a fiberglass pencil
To be honest: 98,7 IS NOT 100 Cel. deg. ;-) On the other hand, accurancy for temperature measurement by Fluke 179 is ±(1% + 10 digits). So it looks "OK".... OK for Fluke.
great video. thanks!
Great! Thanks
most common electrical failure is caused by corroded contacts in Ford cars. I suspect this is the case in all other manufacturers. PB, electronic eng. technician.
thank you, the video was very useful.
Nice one maar volgens mij kun je de beschermlaag met aceton sneller weg krijgen.
dude I feel your pain! thanks to your video I just finished installing my gf window after gutting it out and adjusting like a million things. it took a lot of time and patience but worth saving money. THANK YOU SO MUCH FOR YOUR HELP MY GF THANKS YOU ALSO HAHA
:) I hope she can enjoy here cabrio again with her windows open.
Mijn complimenten beste, een goed verzorgde DIY video met een heldere uitleg en lekkere muziek ;-), ik heb ook een Cruise Control probleem met mijn Audi A4 (deed het bij aankoop al niet) maar ik ben er nog niet uit of het nu in de schakelaar zit of dat het de printmodule betreft, maar daar komen we wel achter.... Maar graag zou ik al het e.e.a. van je willen vernemen, zoals met welk soort soldeer, temperatuur en soldeervet je de klus geklaard heb en waar ik dat spul om de print te reinigen kan kopen/bestellen....?
Ik heb gewoon een standaard Weller soldeerbout gebruik en normaal soldeer. De ouderwetse 60/40 legering. Ik zou geen vetten gebruiken om de print te solderen dit zou de print kunnen aantasten. De Trichlooretheen heb ik via een website gevonden op internet. Er zijn inmiddels wel andere middelen leverbaar als vervanger voor Trichlooretheen. Als je Google gebruikt is het vast wel ergens te vinden. Ik zou de factuur ergens op moeten zoeken om te achterhalen waar ik het middel gekocht heb. Om te achterhalen of het de Cruise control unit is of iets anders dan kan ik je deze video aanraden. ua-cam.com/video/Xb2q9ChNNkE/v-deo.html
Bedankt voor je snelle uitgebreide antwoord, hiermee zou het mij zeker moeten gaan lukken, alle spullen heb ik in huis, behalve de solvent dan, daar ga ik even voor googlen, b.t.w. de video die je me aanbeveelt had ik toevallig gisteren bekeken en was erg nuttig, ik heb er meteen even een pdf je van gemaakt ;-) nogmaals bedankt....