Відео

Nice job sir Nice Tractors Nice show sir 👏👏👏👏👍👍👍👍😃

I think if you reverse the Bronze retainers on the steering shaft, it will let the shaft seat more towards the bell housing.

Just finished rebuilding my waukesha in an oliver 88. It was neat to see one on display

Here’s the playlist for this series: ua-cam.com/play/PLLEKEquedPvfAblZ2Dzzc1Yo64K6y1dgs.html&si=XvLIagB44KvECcsG

I like that tap handle, need to find one of them. It's looking really good. Now I realize I'm 8 videos behind on this girl. Mike, a flat tire? I couldn't imagine.

Come on Mike! He must have a flat tire!. 😆

Oh my goodness he got it done!!!

Nice tractor

Nice job sir Nice tractors Nice show sir 👏👏👏👏👍👍👍👍😃

Always nice to get as much stuff under roof as possible. Good to see the radiator repairs are holding. Not much snow here, (yet) either.Most of what was here melted last two days. I rather like this time of year when it's not snowing and creating work for me! No grass to mow, no garden to hoe.....

This film must be from the late fall, or did you guys not get any snow?

Nice show sir Nice Tractors 👍👍👍👍👏👏👏😃

How many horsepower is that 99

453 or 353 in it

What is the hp of that super99

Nice 310 turboed mine was a 1750 310 naturally aspirated

TWO OLIVER GUYS USING THEIR WITS TO GET AN OLD TRACTOR 🚜 BACK UP AND RUNNING 🏃 WOO -HOO !

He did his best.... 😆 🤣 😂

Nuthing like a deere

😮😮 the cores was stopped up because the raditor wasnt flushed or washed out over the years it will be build up over time and wont let it flow 😮😮 thats why it runs hot other wise U have 2 take the raditor 2 a shop and have them boiled out U can check the thermostat that way U boil them and see 👀 😮 if they open like they should it should open all the way if it doesnt 1 side will and the other side will hang up most pepole just replace them theres no telling how long they have been in the tractor 😮😮 OMG 1 1O 2O25

Patches on Grandpa's pants tell me he is the real thing.

Another great plowing video, don't know if there is enough on UA-cam to get me through the winter though? The fall plowing question, dirt mellowing over the winter, ;like everyone else said. Erosion would be the big strike against it though. Spring plow-days are hard to find. I'm going to hope to make it to Reedsburg this year, again. So far I've never gotten there, even to watch.

Very nice, especially the plowing. That's always my favorite. Are you going again this year? There is a chance I may make it if the ducks all line up.

Boy, Mike K. takes a serious beating in this one! So much for my dream of opening a tire service with him. Great recap of the year gone by, thanks!

Great year end video. Enjoyed the look back format even though I've already seen most of the original videos. Have a great 2025 guys! Oliver On!

ONE OF THE BEST YEAR END , LOOKING BACK VIDEO’S I HAVE SEEN , BAR NONE !

Still enjoying working with Oliver's for 65 years!

The injection pump on that 5050 looks like a lucas/cav just like the Perkins massey ferguson engines, and like the IH on the bd154 diesel engines.

I had a list of all the ACs dad had, but I’ve lost it. I believe that he had a B, C, G, WD, WD 45 D&G, D14, D15, D17, D19, 180, 440, and after he sold the farm equipment he bought the 5050 for cutting, raking, baling and moving manure.

Some interesting plows there, was that a 416 on rubber? Like the 656 too, not sure what model that was with it though.

Cool I have a AC 720 been a good tractor not very many of them out there

We had an Allis 5050 2Wd 8 speed. Nice handy little tractor. Compared to most 40 HP utility tractors that extra 10HP that the 5050 had made a real difference. We also had a 6080. front half was AC while the back half was Fiat. That little 4 cylinder combine engine AC put in the 6080 really had to work to crank out the claimed 83HP. The 6 cylinder AC 185 could outperform it.

Looks like a really fun show. Do you ever make it to Badger Steam and gas? Maytag made ''conventional's', wringer washers through 1985.

Interesting history you have recorded here. As you mentioned Fiat tractors and powertrains showed up in many colors, and names. Fiat licensed the use of its tractor design to many different companies, allowing Fiat to reach markets around the world. Kubota added their 6 cyl. engine to the Fiat Powertrain to create the M4500, and later AC purchased powertrain components and added an AC engine for the 6000 series tractors. That AC 5050 in the video was a based on the Fiat 540 Special DT, and it is equipped with the optional creeper gear. The DT indicated front wheel drive. Very nice tractor for its age. AC imported approximately 12,000 Fiat tractors during that time. AC tractors were manufactured in Romania, while the Olivers were manufactured in Italy. Oliver never imported the Fiat 540 and the comparable 3 cyl. Oliver 1255 and 1265 were based on the Fiat 450 and 480. The hitch corrections on this unit are due to an internal leak in the lift circuit. Most likely at this age it is the piston seal of the lift, or possibly a leaking circuit relief valve. Either one of these concerns are easily repaired through the front side of the 3 point hitch housing.

That’s the first 5050 I’ve seen with a 12 spd (all kinds of 8s) Thanks for sharing!

I have a tractor that needs to be on your list, The Allis Chalmers 5045.

My Grandfather bought an Oliver 1365 back in the mid 1970s. I still have it. It now has about 6000 hours on it now but still runs really good. My 3 point bounces, too. Maybe I'll redo that someday.

VERY INFORMATIVE VIDEO , AND SOME REALLY HANDY LOOKING TRACTORS 🚜 FROM YESTERYEAR !

Merry Christmas.

That's a cool way to plant spuds. Maybe a monitor could be fitted to the planter? Just kidding. What do you do with so many of them? Besides shooting them at other Oliver types.

Pretty interesting old machine, never seen one quite like it. Two types of people I hate to bid against at auctions, Amish and Women! They are both very determined.

The 4 bottom roll-over looks like it has the high-speed bottoms on it possibly?

That 660 is super sharp! And those ever present stones.... Think I need to start growing some winter wheat so I have an excuse to plow in the summer.

It did an amazing job covering the trash, and a nice job overall. John Gaard, I think that's right, popped up on my feed. All things moldboard plow, maybe you have seen it? Anyway, watched and learned a lot from some of his stuff, wish he had more.

Check out my video where I tour the Waukesha engine museum: ua-cam.com/video/ABr0j1P6De0/v-deo.htmlsi=44z7xsx77Jz3QXrg

Unfortunately small engines have been discontinued for a while. The Waukesh location is where engineering, training and remanufacturing are located. Product manufacturing is now in Canada

GREAT RADIATOR INFO ! SO LETS HEAR IT FOR FASTENERS , WHAT WOULD WE DO WITHOUT FASTENERS , THEY HOLD OUR WORLD 🌎 TOGETHER !

I can’t believe this landed in my feed, Fred M. Young was my grandfather. Cool video!

I need a trailer plow like some of the ones you have.

That is an interesting part of history. Guess I'm on a history kick this morning.