Відео

Find (by elimination) the fuse on your panel board that cuts power to the washing machine. Otherwise turn off the mains...

Απευθύνεσαι σε όλο τον κόσμο και λειτουργεί σωστά (σχεδόν) το Auto-translate του youtube για τους υπότιτλους.. Αυτή ήταν η σκέψη..

Welcome!

I totally agree! It had a runout result!

That is so true!

Yes, hard to get mechanical w. machines these days.

You should be good. Those chains make a lot of noise when they go bad, you would definitely hear it...

You are welcome! I got the part from a local shop in my country, i doubt they have international shipping. You can search google for the part number 18150061700 and your country "code" to check for local shops, for example for France search "18150061700 *.fr" without the quotation marks. I see a shop called wolfswinkel in the Netherlands that has it in stock but it better and cheaper if you can find it in the country you are situated. Hope that helps!

Actually it is because i disconnected the battery to do the procedure and that is how it got reseted. I want to do i video update about that... And yes it has come back. The treatment on the plug is to prevent that. After moving the seat all the way to the front and back the light has appeared.

@@varnasfix you told the guy 2 years ago in the comments below that you didn't disconnect the battery. Gotcha! 😎 Lol.. so which one is it? And did you ever fix the light for good? If so, how?

@@ve2430 Yes that is why i want to do a video update on the subject... I didn't know then what i know now :) Even the slightest disruption in the airbag circuit will cause a fault to be stored and displayed by the airbag light. So I must have disconnected the battery as there no other way to reset the code except with a OBD scanner that has SRS level diagnostics.. Will try to do the video update as soon as possible!

@@varnasfix there's a chart that shows what the problem might be based on how the air bag light blinks. Helpful to get closer to the problem.

@@ve2430 Yes part of the chart is shown at 0:35 of the video.

That is a good idea!

The card should be the same in both models… but if you check for new part they are at a very reasonable price!

That is a generic 150w soldering iron...

I am a coin engraver and want to make pins for clothes. Is it possible to add a safety pin to the back of a nickel coin?

what is regular wire type?

@@mulanjamilah7849 guess you could solder a pin on the back. I don't know how well it would hold.

Hello there! First of all are you 100% sure you have the correct brake pads installed and that all the hardware (shim plate and metal piece/spring) was installed correctly? In part 1 of the video i got the correct brake pad part number but the pads were mixed inside the box and got 1X correct and 1X wrong part ua-cam.com/video/8kTC8X2fcMs/v-deo.html... Also applying a tiny bit of copper grease on the side of the pads as seen at 7:20 will help with squeaking / clucking sounds... Nevertheless a tiny bit of clicking sound when moving from forward to reverse and vice versa is normal... hope that helps!

Καλό μήνα! δεν σταματάει και δεν βγάζει κάποιο error με τα led; δεν μου έχει τύχει κάτι τέτοιο...

Ναι δεν σταματάει σέ κάποιο πρόγραμμα μπορεί να πλένει συνέχεια μόνο σήμερα τό πρωί σταμάτησε πρέπει νά τό βάζω σέ κάποιο συγκεκριμένο πρόγραμμα;

@@KargasKargas-cb1wk Το πρόγραμμα δεν έχει και τόσο σημασία αλλά καλό είναι να δοκιμάσεις αν και στα άλλα προγράμματα έχει την ίδια συμπεριφορά... Δυστυχώς δεν μου έχει τύχει τέτοια βλάβη...

Happy the video helped!

Something must be stuck in there..

@@varnasfix hello I have drained it but the flashing light still occur what must be done next?

@@Pbd2kl Are exactly the same leds flashing? If yes then it is the same error... Make sure there aren't any foreign objects obstructing the drain pump. Do you hear the drain pump working or trying to work? if not maybe the drain pump itself is the problem. If the flashing leds are different then it is an indication of a different error...

Thanks for your comment! You are absolutely right! Presenting fault finding and measurements would be more interesting and it is something i try to do in the newer videos... Camera setup did not help for that plus the "first repair" with the second repair were many months apart which made more difficult to diagnose in front of the camera.

Don't think that was caused by frost.... It was in operation for 10-12 years and the rubber just aged and cracked..

Yes that works too! Although it gets the part much hotter until it is ready to come off....

Stranded wire will suck the solder also! On the other hand the solid wire seems to apply equal pressure to all the pins...

@@varnasfix yes true, but it stays in place, when stranded wire absorbs more solder cools down quickly to prevent plastics from melting and can be use for cleanup... Its just a similar way of doing it.. disadvantages cannot be used on very long chips

Go for it!

Thanks for the tip! I am going to give that a try... But how much faster can it be? Plus 1mm2 copper wire is so cheaper... Wick is needed anyway to clean the pads...

A chunk shorter. Mostly it's just less cleanup afterwards @@varnasfix

tried google translate but did not understand...

Me too actually! Did not expect that at all...

Those tips are solid! And yes tinning is a must for longevity of the tips but also for proper soldering... The tip i have destroyed are from brute force (the metal came off) and from forgetting the soldering iron switched on! Now about the cable? Honestly I couldn't believe it was so soft and flexible after all those years so decided to keep the original...

Yes it just works! And it is very versatile with all the different tips... On the Hakko knockoff i have a small tip for the same reason... But most of the times i prefer the Weller with the small tip.. Speed wise in soldering it just does not compare...

Χαίρομαι που βοήθησε το βίντεο! 👍 Νομίζω δεν είναι πολύ έντονο το κλικ. Είχα βάλει και γράσο σιλικόνης και λειτουργούσε πολύ ομαλά. Σίγουρα έχει σημασία και σε τι κατάσταση είναι μπαταρία...

ευχαριστω πολυ!@@varnasfix

That needle point type is so difficult to use... Great work with the soldering iron!

If you refer to the drain filter then most washing machines have it somewhere...

Nothing is designed to last nowadays… the technology “evolution” seems to outrun the useful life of products..

Indeed they were the shit back then! Served and serving hours of soldering :) I think now they are overpriced, but on the other hand all the good ones are...

maybe some other issue? was everything cleared in the drain?

Sim, eu limpei. Agora começa a funcionar e para , apaga as luzes e fica acesa somente a luz do cadeado.

Thank you :)

The third capacitor is a low impedance 100uf 25V one... It was not broken really measuring about 88uf with good ESR. The Panasonic FR series (same model as the other 2 ones) is a good replacement.

You are welcome!

Yes possibly (from a coin or something) , use pliers and try gently to remove it taking care not to damage the plastic… it has happened to us as well.

Al final la puse de lado y destornille el filtro de la chapa, removí al mismo tiempo que volvi a intentar abrir el tapón del filtro y por fin pude desenroscar y sacar palitos tijeras de costura pequeñas y volvi a colocar todo. pero sige mal la lavadora al igual que coje agua la suelta a los dos minutos sin dar vueltas , tengo que ir jugando de progrmas en programa para que lave y centeifuge ..

The Top246 IC gets very hot during its operation so brown/burnt silicone on its legs might be normal, plus if there is a problem with this IC the unit is dead and does not power on.... First of all you should check the heater element and all the sensors associated with it... Hope that helps!