Відео

Hho Technology prolonging engine life and engine oil life. Engine life changer device improve engine performance and increase fuel burning efficiency beter then a new car!!! More fuel will burn in the engine No un burn fuel wastage . Engine will run more power ful .Consume less fuel. Engine runs smoother reducing carbon emissions significantly . Boost engine power and torique. Better acceleration . faster running. An efficient hho car kit lower the engine temperature more then 100 degree F. To prevent heat build-up.Hho car kit reduce car maintenance charges. Cleaner engine running. Reducing engine noise due to the faster fuel burning. Hho car kits works nicely requires no modifications in the car engine. No side effects on car engine. Engine start quickly safe your car battery. No more petrol or diesel smell make your car a low cost hy-brid. Use a Hho car kit small or big.

Even though the title of the video is "Making a Chicken Tractor". In a video lasting 9:58 minutes, we did not see anything being made or montaged.

*promo sm*

How can JESUS send God.

You use a voltage divider for MAP for newer ( early post 1996), the open loop could be because you're just adding resistance that computer can sense in current?

When u disconcerted the negative from the battery u should short with the positive cause it holds potential on the liquid / A Cell its just battery a car battery but without the acid with its the eletroquimic component that hold the charge on the battery/ on the cell the energy its released in the gas that u produce by the plates. So it's charge the water and want u touch with the hand the difference int potential discharge with spark that / the spark travel the plates by the empty area where the liquid was out then the spark reach the positive plate on the gas space that create the perfect environment for the explosion if was full of liquid will not do that or if u short the positive negative disconnected that also prevents the spark static

Why u stop the test on the project/ or u just find the root of the problem/ and fix can u tell if it's need cell or u can just get the economy by change some spect on the engine/

Hey man my girlfriend and i think thats the coolest chicken tractor we have seen and such a great video. Well done

Should I connect the enhancer directly to the map sensor or should I connect it to the ecu inside the car on the yellow wire or the voltage will drop if I run the sensor but to inside to connect the enhancer

I am a engineer and I see that circuit need a better design I suggest a design of using the trim pot as a automatic turn on the throttle so when the engine started the unit is off and to stop the opening on the ecu and that will fix your issue of using your hand to turn on and off

You used 50k potentiometer in enhancer

One of the best I've seen!

I wish mine was this nice lol. ua-cam.com/video/PM8n2d9GtSo/v-deo.html

Do you also sell the EFIE unit? what are there priced at?

Great build!

This is excellent information. I see it as better than Justin Rhodes design. Thank you

chicken smooth your going to miss that pool tin when its all gone

Sid you did a great job with those chicken tractors. Thanks for sharing!

6 yrs old....how is the PVC holding up ?

Great coop but one question...dont the raccoons etc. Manage to go under? I think I would have to put a screen of some sort on bottom.

nice sir best of luck from Pakistan

can we not by pass these Map Maf sensors?

Best chicken tractor I've seen so far

Some great ideas here, thanks for sharing! I was requiring something much larger for turkeys, so I dug up my welder and some old bike parts... ua-cam.com/video/0ycLORfNeNc/v-deo.html So far, it has done well. Brad

Raccoons can also turn those latches. You may want to look into a better locking mechanism. We had to screw ours shut to keep those vermin out of it!

I don't know the exact width. Since this build I've moved and gave the chicken tractors away. I know that I made inside to fit 4 foot width garden bed so it's probably 4 1/2 to 5 feet wide.

can u give the exactly width measurement sir...i know its 10ft long.

Sid Nash...this is good tutorial...💪🏻💪🏻💪🏻

thanks amazing good information.but if u joint it before us with its part it would be far better.Anyway good you showed it

Thanks this was very helpful

Seems heavy.

Thank you for the information

There is no o2 oxygen sensor in the vehicle

Hi, I have a Ford Mondeo MK3 diesel What about a Wire MAF and MAP What should I do wire 12volt or 5volt or 1.2volt

I like how your design fits right over your raised bed garden plots. That is a nice design feature that I will probably be using from you. Great ideas, it looks like we will be getting chickens for Christmas this year.

where I can purshace this

Seems as though there was a slight increase in fuel consumption at the end of test 2 & 3, and that unfortunately you ran test 1 in the opposite direction, which likely would've read lower. I'm wondering if this configuration would ever throw engine codes. I have the same model Sienna. Are you running any EFIE'S or O2 extenders with this set up, or at any time with this configuration, either before during or after?

It's been just about four years; are your chicken tractors still in use?

actualy i did want see the fuel economy difference

Schd 40 or 80?

Looks like you cut them all.

Hi, why did you change your mind, hope you have time to answer, kind regards Vic

+E Alfaro, "self cleaning" may be an overstatement. But, when you pull the floor out, most of the chicken droppings are scraped off onto the ground. See my full-build video for more detail. It is linked near the end of this video. -Sid

Use spit to lubricate the bit.

no problem with wind at all. I think it's because of the rounded roof and the weight of the wood inside. the screws through the PVC have not been a problem. I thought they might be. But the PVC is soft enough that it holds very nicely

no problem with wind at all. I think it's because of the rounded roof and the weight of the wood inside. the screws through the PVC have not been a problem. I thought they might be. But the PVC is soft enough that it holds very nicely

Have you ever had any problems with wind? I have a similar build that was blown over this morning. It's not fun chasing chickens in the rain...

Nice tractor. I like that you salvaged the old pool walls to use as roofing.

Two people could easily move it without the wheels, but it is pretty hard for one person. That's why I added the wheels. The PVC pipes are thick enough that the sheetrock screws I used continue to hold very well. The only clamp that came off was due to being scraped off with a good deal of force while moving it. None of the PVC to PVC screws have failed. I have had trouble with the staples that hold the hardware fabric to the wood. I've had to replace many of those. I should probably use screws there also.

Well done. I am left wondering though, how you keep the screws connecting the PVC, and the clamps holding down the hardware fabric from stripping out of the thin hold they have in the PVC when it is flexing apart every time you move it.