Відео

Love Yamaha boats!

The original fan had three screws holding it to the shroud, the new fan has four. How did you mount it?

Still working good?

I got a 01 that spits and sputter low rpm’s but runs good at high rpm’s

Clutch or parking break sensor unplug them

I know this is an older video, but was curious on how well the boat comes out of the hole when pulling a tube? My jet boat always feels gutless with a 2 person tube behind it.

🙏🇺🇲U.S.N⚓🧭 I LOVE YOU SAILOR'S 🫶 MY LATE FATHER WAS A NAVY COXSWAINS. ~ SEMPER FORTIS ~ 🫡🇺🇲🙏 STAY SAFE AND BLESSED!! THANK YOU FOR YOUR SERVICE AND SACRIFICES FOR OUR COUNTRY. STAY SWEET ⚓ SALTY ❤🤍💙💪🤜🤛

5 years later, your video and detailed info were helpful in my troubleshooting process. Thanks

Is that the only grease point for the pump bearings? Or is there one on the other side next to the other motor as well? Sorry for the dumb question

Hello John I have a 2004 and have the same problem with a new carburetor what do you think will be Thanks

Thank u for this video

Heck yeah. I like it. Beats the specialty tool system

Mine stalls out after riding for so long and it’s always around the high end of the second gear but I can trick the bike to keep running with the kill switch! That’s just after 15 mins of riding and it warmed up for about 15 mins aswell before I drive?

Este fallo de coriente no selera la coriente bien donde va el estator tiene un chabeta enel sigunial esta rota ino maneja vien la coriente soy mecanino 20 años de xperiensia

La chabeta de motor esta roda donde va el estator hay una bola manitica tiene tchabeta rota

So I have a all stock 660r and it has stock jettings and all the switches are good there’s no leak or air leaks or anything but when I’m driving it slow it drives fine when I’m at full throttle it drives fine but when I drive it at cruse around mid throttle it backfires and blows air back out of the carbs

Where do you think I can find the lyrics?

If you have mid range problems and still want to ride. Adjust your fuel dial to off then go 1/4 turn to reserve. Once that is set, push your choke lever half way. Full revs back

Tengo un problema con una raptor 660 cuando acelero al maximo empieza a fallar como que se corta la gasolina

What’s wrong with mine it bogs if your not in high rpm and if I have the air filter on in runs even worse

What is the part number?

mine did that and it needed the valves adjusted as well as the spark plug port had water inside

I am going to have to check my valve clearances. Mine wont start unless i have the choke full on and manually release it once it is fully warmed up. It also backfires a ton when I get off the accelerator (decel)

Did it have the right connector or did you cut and reuse the old one?

How has the fan bin holding up mine just died on my 16 xxc and bin debating on going with the spal fan

here in 2022 having the same exact problem as you did you ever figure out what was wrong with it

Fmf o yoshimura for raptor 660?

Did u ever figure it out ? Mine does it the same thing when it's warmed up alot. And alot of black is coming out the exhaust

imagine in 2022 getting one like this for $1000 ??? haha times certainly changed!!

its called rev limiter while sitting in neutral it will not allow you to rev the engine

Eso es un censor de la emergencia

Hello I have a 2008 Kawasaki kfx450 doing the exact same thing except it’s fuel injected. Any solutions?

How did you mount the fan from the inside of the housing?

Definitely carburetor they have a twin carburetor setup primary carb is left side secondary carbs for higher throttle position secondary carbs opens up

Mine did that when the timing chain stretched. Sounds like yours is rattling

Do think this will work on a 2019 renegade

I recognize this place. Virginia....

Are you working with them? or you a normal citizen????

Just a quick update on this one.. The chattering noise you are hearing would not be cleared up by greasing these bearings. Most likely the noise is from clearance issues with the impeller and wear rings. I'll be replacing the wear rings and inspecting the impellers in a few weeks and will make a video doing so. Thanks for watching!

You all true hero's,Thank you to all.

The tricks looks like way more fun of a Seadoo.

What you do to fix it? I having the same problems

I have a 17 212x same rattling noises when it’s out of the water idling. Definitely a good video though. I need to start greasing that. Is there any other grease spots on the HO engines ? Thanks

What fixed you’re problem because when I have mine in neutral it revs good but when I’m driving it and full throttle it starts to sputter

Let's see that wrap!!

the noise your hearing isn't from that bearing. it comes from the jet pump assembly. this noise is normal for it and all jetski as well.

My raptor 700 R.. Has the same problem 😢😫.. any idea how to fix this

How long are the cords from the led strip to the power unit?

I just bought a 2021 AR190 with the 1.8 engine. How aften should I grease that part. Every year about 5 pumps a year? Anyone have an idea? thanks.

That top plug on the clutch side is the problem it’s missing and will make it sputter and backfire when throttled