Відео

Try hooking the cable to a 8’ 2x6 board and sled it down the topside, saves a lot of time especially if the hoods are already on.

Well, guess what guys? I don’t know how to weld in my bumper came out meant never welded in my life asked my cousin to borrow his welder. He said yes watch the video for about five minutes. We did it together came out clean so you don’t need to know how to weld as long as you’re determined, don’t take that advice that you “need to know how to weld”

nice

Could you use a slightly smaller & temporary bridge piece with attachments installed on each end, and hook it up to old and new belts? Let the old belt pull up the new? Or is there no room at the tail end to remove old belt once it comes off? I use these in flat wire belting and 150-200 weight belts, but curious about monster belts like this. Is there a reason not to have new belt cut to length and lacing pre-installed?

1/4” steel? How long until the material wears out that wall ?

Bro please take sum safety precaution while working the lives are important

Very nice, great job. We are just the belt Joint machine maker

@TurninNBurnin Great job! It is possible to find a book or article that describes the steps of installing the conveyor.

Damn that's alot a guys. I get stuck doing that by myself but I have a winch. Still alot a work

Thankyou for sharing vidio, very good work 👍

I almost bought that kit for my 69 but didn’t like the position of the coil overs, about 2” away from hitting the ground

What side steps are those?

Yeah that's the one boyz

nice truck, and love the wheel/tire combo!

Them brass knuckle dials are sweet

What's the hp of this motor

How much would the whole setup cost?

I am a professional manufacturer of conveyor belts in China. If you need anything, please contact me

My boss would send 3 people to do something like that. We be dog ass tired when we done but we get it done

Sand and gravel.

How many feet of conveyor was that? What size cable did you use to pull that?

Gotta do this today 😢

Makes it nice when you have enough help .I worked Asphalt ,Sand and Gravel for 41 years so I know

👍

ua-cam.com/users/shortsQQjRUFGwoqk?si=d2m0BU7Tn6X6LYKX

amazing vid man! norcal the fenders. tbh idk what the point of lifting the truck - it does nothing but wear everything out and harder to load the bed up. the diff is still going to crash into everrything unless you somehow do a diff lift

Look very nice !

How did this turn out? Or ongoing?

Uncle Lon, really!!!

Gay!

Huge waste of time but ok

Who manufactured the exhaust system? Where did you order it from? Looking for a system like that for 2012 F550. Can’t find one for it. Thanks for the video.

Great Job

Unrelated question, but how did you correct the gap between the headlights and the side fenders????? Sick looking truck!

What happened to you? These are great videos, would love to see more.

Man's gonna catch Fire😅

My guy is crispy… okaayy😂

What kind of jeans are those ?

I need work Mr.

Looks amazing, way better than any bolt on bumper, and way stronger, I'm so impressed, just ordered a Move bumper yesterday and hoping it turns out similar to this

Can do any thing with hummer right

Thanks for the video. I just purchased my 4th 69 FB and plan to do the same you did. What gears did the Firebird have and the rear end.

Looks great man, just ordered my bumper for my squarebody yesterday

used to do belts in Maine. brings me back!!

Jesus your a good grinder maby a good fitter but not a welder bud and wtf are you useing Flux and gas for lmao redneck dual shield action or you siting there sucking all the gas out your mig gun like your trying to suck start a lbz like you have the right ideas just need to work on execution bud

What shirt is that?

tired of hearing the phrase go ahead

I have the same truck , only 2003. Did the side molding come off easily? Heat gun/hair dryer?

Does the 4" lift cause any big problems with suspension or front end?

I wish i can work in such big company and become a construction monster I wish luck for all the groupe members