![Raine Lutz](/img/default-banner.jpg)
- 277
- 1 037 341
Raine Lutz
Canada
Приєднався 14 кві 2011
Just posting videos of my builds along the ways!
Straight Piped BMW E63 M6 V10 Flyby & Revs!
Absolutely savage exhaust sound from my straight piped 2008 BMW M6 with the legendary V10! A couple flybys and of course some revving!
Переглядів: 84
Відео
An Absolutely GORGEOUS Mclaren 720s TOTALLED For Such An Easy Fix!
Переглядів 9День тому
This absolutely beautiful Mclaren 720s is the latest piece of machinery to end up in our shop, for a really stupid reason. A minor engine fire caused this poor 720s spider to be written off, and along its journey to our shop a tow truck driver managed to punch a hole in the front, AND rear bumper, as well as "lost" the key.
BMW M6 V10 COLD START! ABSOLUTELY BRUTAL!
Переглядів 1,5 тис.14 днів тому
Absolutely brutal cold start, and rev video of my gorgeous BMW e63 m6 with the legendary v10. Car is straight piped and sounds amazing!
Rare Gated Manual V10 Audi R8 Engine Fire!
Переглядів 1847 місяців тому
This unlucky gated manual v10 Audi R8 didn't stand a chance against the engine fire it found itself engulfed in. Disappointing to see a tastefully equipped R8 in a state like this.
My New Mustang Gets A MAKEOVER!
Переглядів 1307 місяців тому
SUPRISE! I bought another Mustang! Today I turn my boring stock 2000 Ford Mustang into something a little more respectable, A BEAST!
HOW TO: Jeep Wrangler JK Turn Signal Switch Replacement!
Переглядів 7187 місяців тому
Quick and easy how to video on replacing your Jeep Wrangler JK turn signal / multifunction switch.
Crashed 2021 Ferrari Roma ! Beautiful Spec!
Переглядів 2627 місяців тому
2021 Ferrari Roma with every possible option, absolutely destroyed. Couldn't get it running but managed to power it up and take a look around!
2005 Ford GT Wrecked With Only 6K Miles!!
Переглядів 647 місяців тому
2005 Ford GT GT40 with only 6k miles absolutely destroyed! It was brand new and original, including tires and even the door sill protective film!
Installing Skunk2 Lowering Springs In The Honda CRX!
Переглядів 4007 місяців тому
Suprise! We have a 1991 Honda CRX! Today we ignore all of the rough body damage and rust, and we solve the biggest issue of them all! We threw some Skunk2 Lowering Springs to take care of some of that ugly wheel gap! This is our 1991 Honda CRX si barn find, and hopefully I make some more videos of this poor thing..
2023 McLaren GT Destroyed !
Переглядів 347 місяців тому
Brand new 2023 Mclaren GT with less than 5k miles on it absolutely destroyed. Heavy front end damage, roll over damage, and the left rear brake rotor even managed to get destroyed and fall out!
Twin Turbo Camaro Burnt Down! Transformer Edition!
Переглядів 757 місяців тому
This rare 2010 Camaro Transformers Edition had some big ol' turbos installed, it's hard to tell though, as the entire compressor housing on both turbos completely melted off. I've never seen fire damage quite this satisfying before and its actually quite impressive.
Whats Left Of One Of The Very First McLaren 720's Ever Built!
Переглядів 507 місяців тому
All that is left from one of the very first Mclaren 720s ever built, the "Launch Edition". Absolutely destroyed with barely anything left!
Totalled Lotus Evora 410!
Переглядів 627 місяців тому
Quick walk around this totalled Lotus Evora 410, rolled over on a racetrack and unfortunately not much survived.
Flooded McLaren Walkaround!
Переглядів 213Рік тому
A quick walkaround of a 2018 McLaren 570s to show the damage on this poor monster. Only 8,000 kms when it had a run in with some water.
Junkyard McLaren walkaround !
Переглядів 309Рік тому
Quick little walkaround of a 2018 McLaren 570s that is just sitting in a junkyard!
Wrecked TT Lamborghini Gallardo Walkaround! CARNAGE!
Переглядів 399Рік тому
Wrecked TT Lamborghini Gallardo Walkaround! CARNAGE!
HOW TO: 09-14 Ford F150 Column To Console Shifter Conversion!
Переглядів 9 тис.Рік тому
HOW TO: 09-14 Ford F150 Column To Console Shifter Conversion!
Center Console Swapping My UGLY 2013 F150!
Переглядів 9 тис.Рік тому
Center Console Swapping My UGLY 2013 F150!
Introducing My Newest Financial Mistake! F150 Ecoboost Build!
Переглядів 234Рік тому
Introducing My Newest Financial Mistake! F150 Ecoboost Build!
HUGE Updates! Where I've been, Project Cars, And PUPPIES!
Переглядів 159Рік тому
HUGE Updates! Where I've been, Project Cars, And PUPPIES!
Cat Eye Front Clip Conversion On My 2000 Silverado!
Переглядів 7 тис.Рік тому
Cat Eye Front Clip Conversion On My 2000 Silverado!
LS Swapped Mustang Ratchet Shifter & Center Console Swap!
Переглядів 524Рік тому
LS Swapped Mustang Ratchet Shifter & Center Console Swap!
Throwing A Front Lip On The Civic! Best Mod So Far!!
Переглядів 3742 роки тому
Throwing A Front Lip On The Civic! Best Mod So Far!!
Building A Custom Exhaust For My LS Swapped Ford Mustang !
Переглядів 2,5 тис.2 роки тому
Building A Custom Exhaust For My LS Swapped Ford Mustang !
Building BEAUTIFUL Custom Headlights For The Genesis Coupe!
Переглядів 8032 роки тому
Building BEAUTIFUL Custom Headlights For The Genesis Coupe!
How Much Does It Cost To B-Series Swap Your Civic? (Budget Build Eg Civic Swap)
Переглядів 3,1 тис.2 роки тому
How Much Does It Cost To B-Series Swap Your Civic? (Budget Build Eg Civic Swap)
Make more videos of Subaru being ls swapped, please
Need some help I have a 1996 Honda dx hatch and swapping a b18b1 in it what wiring hardness should I use?
S85B50 is a legend
sounds like fart
@@zaxdsus Noooooo! Can't unhear it now, thanks for that 🤣
@@spontaneousgiraffe jk its awesome man❤️
What size crush washer?
I feel your pain, literally. 30 years if my lfe. 😢
Over 35 years for me.
What happens to the cars after these videos
Oh you mean literally an engine fire. I thought you were starting the car…lol
Are they still holding up?
Are they bouncy?
What was the shifter cable part number
this is not a fuel cut this is a ignition cut.
This is a lot different than what is in my 2002 Mustang GT.
What throttle body gasket did you use?
Use lots of Bondo !
How much would you charge me to do mine 😂😂
My gas gauge always reads full would the sending unit still be a problem?
I DID MY SWAP IN A DAY TOTAL PARTS $250 CONSOLE SHIFTER CABLE WIRING CORRECT STEERING SHROUD
Good video. Suggest changing the title (91-00) to match the actual year of the car as indicated in the video (96-2000). Nice walk through though!
Man I’ve been looking for this for a WHILE gonna wire mine up!
Did you figure out the bolsters ?
🤣 bro that was fucked
My ek has a d-series in it, so that upper driver mount is self explanatory? Just ordered a set from plm.
Thanks for this.
Hey no worries! Hope it helped!
great video dude i have a question about the ls swapped mustang, what did you do for the engine wiring and ecu? thanks!
I just used a factory truck harness and ecu, get a custom tune, and it's cheap and easy. You will have to do some work on the harness, such as repinning some connectors and removing wires. There are a lot of write ups and resources for you to if you decide to go that route. It's not difficult, but it is tedious.
@@spontaneousgiraffe thanks a lot dude your a huge help and inspiration keep it up!
@@cadenchristiansen3553 hey thanks man I really appreciate that!
Are these straight swap? From the mounts?
Yep, they physically bolt right in. It does require some wiring, though, to retain full functionality
Love the man to man talk, “ehhh” “ughhhh” “ahhhhh” … video “agggg”
i got a 96 integra gsr with a stock cat and stock exhaust, will this header system fit on it?
Skipped important steps👎🏾
Any links to where to find wire diagrams
i had the same issue with the downstream o2 sensor lmao waiting on mine to come in now
Update? I just picked up a 310k mile mustang Gt as well
Unfortunately not a good update. It has never let me down and was a ton of fun to drive, however i did pick up my dream car so I'm selling this black mustang to make room for it. I still have the red LS swapped Mustang though!
Installed these on my turbo b séries in my ek. I’ve been on 3 drives so far and the vibration is so bad in my opinion. Does it get better after breaking it in?
No unfortunately the vibration will remain, an unfortunate downside to solid mounts.
Thanks, what you suggest in your video works great. I have my fuel level indicator working now.
what did you end up doing with the coolant cross
Does it have a true 2.5” collector? I heard they have a smaller tube inside.
nice !
asking myself if i should follow tutorial when seing all the video titles with 'blown my xxx yy ' 😂 amazing vid and work 🤓
Hey man I got a question. I got the oil pan you have for this but have the solid steel engine mounts. E gone will not sit in car Did mounts you use make a difference hookers were they. Got a part number
Anyone know if it is possible to go from Console to Column?
I'd saybits possible as the hardest part is the wiring and it's similar to this. Only issue I see is you'll need the actual mechanism on the column the shifter mounts to. I'm unsure if you can swap it or if you'll need a column shifting column.
Do you have to do anything to the ecu?
Nope nothing at all!
0:55 that “YUP” at the end 😂
👍🏽
Hows the header holding up?
Sorry for the late response! I've run these long tube headers on all of my civic builds and i have nothing but good things to say about them! I even bottomed out the car a couple times and caved in the header. still no issues even with a big dent in the tube!
So will the Integra GSR accessory brackets work as well? basically, I’m doing a b20b swap in an EK and I happen to have the GSR brackets I was wondering if those brackets would work to keep AC and ps
D Series AC compressor only works with CRV or del sol brakets from a B Series
No one shows how to remove the springs every video I see skips that part I have a 91 wagon pretty same thing
do you have link to buy thus
Hey man I’m building basically the same car but with a lq4. Was wondering if you used a t56 if so what you did for the drive shaft as well as exhaust and oil pan. It’s looking like you have a truck pan. But I was reading that you need the 302-2 low pro pan.. any help would be appreciated thanks man
Oh you're going to love it with an lq4 that will be a ton of fun! I went with a built 4l60e on this one actually, but I got a custom driveshaft built for it. This engine originally had a truck pan on it but I did have to swap it with a holley 302 pan (the truck pan hit the factory crossmember) I could have notched the crossmember but I would've had to cut alot out so I just used the low profile pan, and it just barely fits haha.
I would say you did a really good job and in my opinion worth the cost, I actually thought this would cost much more than this
Hey thanks man I appreciate it! It can definitely add up and cost alot more if you buy everything for the swap, instead of building your own exhaust or transmission cross member for example.
Good video bro 👌
Hey thanks man I really appreciate it!