Відео

Might have missed it but can't see a means to safely isolate the batteries in this layout. Is that ok?

In my inverter dont have no one burn spare part elettronics, but errore 09 appeare any time, what I do?

Do you have a link to buy the full setup?

I have 2x US2000 but they are not connected with the RJ45? Can I as 1x US5000?

Hi I also have a problem with the F08 error, it happens especially when it rains, could you help me solve it, thanks

Hello Voltacon Solar, do you know how many cells are in the US3000C and US5000C batteries? I think the US2000C has 30 cellsat 25ah each configured as 15S, 2P.

I have just one inverter that gives me 08 error when I switch mains on

I mess about with solar on small electrical projects for fun and often lean my portable panels against my south facing wall, makes sense if you’re out of roof space or like me when it’s just not practical to climb onto the roof to charge an iPad 😂

In this project the bifacial factor does not matter we used a large panel to absorb more energy. Most of the panels now are made biracial though.

Nice shadow on the bottom one.

I've never seen bi-facials mounted so that light has trouble getting to the rear of the panels..... mounting on walls, unobstructed south facing is a great idea but not sure the ROI on those panels with micro inverters makes sense.?

When do you but this do you still need other certificates to apply for feeding tariff? Or just number from you and you can plug yours?

what are the commands to do the voltage calibration?

Which mode have you used on this inverter? I have similar one, but I am worried about the lack of communication between the pylontech and the inverter

Replace that white board with a large mirror. The result would be amazing

It's great and customers do not get any support yes no reply from your help email.

May i ask why i cannot increase the charge amps from 30amp to 100amp , i have 3 batterys connected. I am still no further to getting the wifi device to connect to the app. Great product but slowxwith help . If i could get my wifi connected you could remotly see it. I have tried on iphone and android devices same issue it sees the wife device but does nothink but wait.

hey; please I have a sunnyisland inverter which is sending a F952 ExtBMStimeout error on the sunny remote control after connecting with the BMS. Am using pylontech US5000... How can I solve this problem?? Am using the specific cable to connect the BMS to Sunnyisland inverter

Thank you so much for your video! What is the rj45 pin interface on the battery side? Could you share please

Hello! What cable you using for connecting BMS battery to that inverter?

Do we have a simulation software for performance analysis of the bifacial PV?

I just mounted a battery and made the configuration. I powered off the inverter after that and turn it back on with flames above and error 09. No input panels, no output ac. Only the battery. Im sure the mosfets are gone but dont understand why. I guess a production fault.

Perfect thanks just what I was looking for

Hello Sir, i have install same like features 11kw hybrid invertor, the problem is when utility OFF then invertor trip and output 0VAC, i use without batteries, why invertor trip???

Inverter that i installed flashing warning w08 Temp issues But the Inverter is at cool room with air conditioner What's the reason? Please

What size cables are for the batteries to the busbar ?

I do not think they dispatch to consumers directly unless you have a special arrangement or you know how to do it. Not all people are technically ready

Why should you not replace it at home? Pylontech sends me one to replace it, noi problem jzusrt be carefull with J160 connector!

Very cool. I just bought a raspberry pi 4 4gb model with a 7” OLED touch screen for a total of around $100 on Amazon. Now I just need to purchase the solar assistant and flash it to my 64gb micro SSD. Can’t wait to try it out! Looks like a well thought out and intuitive program showing lots of great data!

Is nice. Connection

nice thanx

Thank you for your comments , yes 3 phase system can be implemented but attention is required when neutral and earth wires are connected

Congratulations! First 480 volt system I’ve seen from Solar with three phase ! I wish your work was seen more like my book Solar independent Utility systems manual I’m censored beyond belief and attacked by local Utility But wanted to say very nice job !

Thanks for the video! How to connect the single phase output of both inverters? A busbar?

Grazie mille for this very interesting and detailed explanations. And obviously, take care of yourself!

South facing vertical bi facial works best in winter, summer is lower, but the days are 15 hours long, balances out. After this months upgrades close to 3kw in full overcast.

Hello, I can't understand how menu 9 and 10 work (AC OUTPUT ON-TIMER). What happens when I set the time interval? Does it disconnect the inverter from the grid?

If you have HS61 fault on your Inverter you need an special Ethernet cable: Batterie side pin 7 and 8 goes to the Inverter sid of 3 and 5. 8 to5 and 7 to 3

Have you ever check the pv voltage early in the morning (07:30-09:00. O'clock) my is between 98-120 and around 09:00 increases up to 380v.

11 Kw solar invertor off-grid, capacitate mică de stocare cabluri subțiri, cred că este pur demonstrativ.

F09 is a fault but E09 is equalisation mode

Error e09 appeared on a single inverter without any intervention from me, although the device was still working. I can rule out 1 input and output connection, polarity reversal and bad parallel connection, because there is only one inverter. After resetting, the error disappeared, but now when I see in this video that it is always a serious error, I was very worried, although at this moment the device works and does not display the error. Can anyone tell me what's going on?

can you explain master and slave output

Hello, the wi-fi module is not visible and I cannot connect. Is this software or hardware?

You need to contact us as this is a critical operation and we can not release the tools online . We can assure you that works and if you have issues let us know and we ll email you the right tool and cable

Not very useful in explaining how to actually do the adjustment to correct the 08 error code ..for parrallel units.. Or what data cable is used or where to connect or what program you connecting to,to send cammand correct voltage output... Usually these Voltacon vids are excellent ,but not this one ..👎

No you don’t need a smart meter , the energy you use will be for self consumption. You don’t have to worry about approvals etc