Відео

Everything is made in China those days. Well they are holding good. Nothing wrong and they did survive quite hard braking from 121kmh to 0 but of course I'm using 15% regen. Now I'm getting Lonnyo 80H and 70H 22x3 motors

Yes, probably.

@@trebor1477 i charge it directly using the charger, it's now alive but the problem now is the chsrger is blinking red 😑

@@074mandy 0 to 100kmh in 9.60 sec

It's written 21S9P so the full charge is 88.2V or 75.4V at 3.6V.

Not yet. I will add them

That is good to hear 👍💪. I will do a Spintend VESC 150A and 50Ah 21700 M58T battery in a month or so.

Yes check all connections for balance contact

Ou … I know the problem. I put the black cable on the wrong place. It should be on top of the battery (on the metal) not on the side metal. (the 5th pack from left to right of all packs ).

Hi. On what version of the marlin are you? I'm on Marlin 2.1 2.1. Yes it is a totally different machine and you can't say it is Anet any more 😁. Uh... Now I see here I had 8 mm rods instead of the BLV mod with MGN12 linear bearings. This is how it looks now ua-cam.com/video/qJNogkC55DQ/v-deo.htmlsi=lHzHv16Qu8V0RX-V

Did you measure all 10 segments in P? Probably there are unbalanced groups or damaged cell's

Sorry if the battery is not holding charge then she is dead. Replace all cells with eve 3200mah and you will gain more AH with the same size battery

@@trebor1477 Friend can you please confirm I am charging Lipo 0.1A 4.7V setting on IMAX It takes very long time each section to charge correct? If mine are above 3.8V slightly then still all cells need changing or possible BMS board replacement?

@@deepmystic6739 hard to say like that. Maybe one from 10P is still not full? BMS don't die just like that. Usually there is other problem. Are all connection points from the battery to the board undamaged. Try to lift them with plastic and not with metal

I did charge all the cells the same. But now I start building my own batteries m.facebook.com/groups/202140770347162/permalink/1396861724208388/

How many V do you get from the battery? Try to press the reset button near LED diodes

@@trebor1477 Batteries all charged individualy to 4v showing 3.87-3.91. Re attached battery and blinking red light. Put charger in and still no look. Shows around 3.6v oit put on wires after BMS so looks as though BMS is not letting full power through. 🥴

@@stevenharris2190 Did you charge all 10P

@@trebor1477 yep all 10 and all around the same. ive also just tried this ua-cam.com/video/4RjLWhz-SWI/v-deo.html

@@trebor1477 is it worth swaping the BMS

Ah yes … i have solution… I confuse the black and red cable 😂 plus and minus. Now it’s works !!

Hi. Yes that is usually the problem 😁👍. But it is good if you have a multimeter to check all connections.

I have the same problem, whats the solution ? I dont understand 😢

@@frankscalda3361the cable black and red should be change on the side of the battery

There are no easy PNP boards. And I will say go with my config but you will still need to configure some Merlin options differently. But it is worth it to mod with the same board. You will get silent drivers and you don't need end switches at all. So less cabling 👍

@@trebor1477 so it means that we have to manually configure everything to match printer specs right? i'm also a bit curious about print result improvement..is it really far more better than the stock board?i've been dealing pretty long time with the ringing and ghosting marks on X and Y axis even after installing braces i have several other printers from other brand and to be honest this one got the worst result and its really a pain in the ass for me to resolve

@@bigboy8692 Yes, but you can use my config and change it

Did you plug it to the charger? Is it charging? Fully charged 18650 cell is 4.20V

@@trebor1477 When i plug charger it's didn't charging. Here is voltages on cells: 1 - 3.99v 2 - 4.16v 3 - 4.03v 4 - 4.16v 5 - 4.15v 6 - 4.16v 7 - 4.06v 8 - 4.16v 9 - 4.17v 10 - 4.03v bms output to mainboard 41.2v Brake light working, forward light too but on lcd only one blinking dot and when i accelerate scooter doesn't run.

@@DDanielQ try to balance each cells as close as it's possible. But there can be that some cells are also bad and they need to be replaced.

@@trebor1477 How can i test cells one by one without messing? I will try to more balance groups too. Blue solid light on bms is an error?

@@DDanielQ you can test only groups if some of them charge up to quickly they are probably bad. Blue is OK . Try to drive a little and then plug it in the charger. Now I don't have m365 any more. I switch to smth stronger ))

Maybe yours motors are to powerful ? I`m happy with my tuning. How many amp pulls your motors in normal flying? I get 5 to 7 A while flying.

@@trebor1477 my go up to 12 amp

@@trebor1477 can you tell whats its yours filters setup ?

@@FPV.ExploreScotland in 3 days because I'm not at home 👍

​@@FPV.ExploreScotland Hi. Are you on discord? It is simpler to send pictures of the settings.

The old setting was probably from changing from BF 4.3 to 4.4 with the old 4.3 BF cli file. And then from 4.4 to 4 4.1 so after the problem I did clean flash and manually transfer all settings in 4.4.1 and then did I get those defaults rates. And after that did everything work just fine.

@@trebor1477 oh i see! so your old CLI file from 4.3 caused the problem when you moved it to 4.4? i read about many bad issues in doing this. so they suggest to use clean 4.4 or clean 4.4.1 default settings. then manually configure everything to make quad fly.

@@renerjose4753 Yes this is a safer way ) but to be on a safe side better check those settings. Oh and don't forget to manually select 57600 baud for GPS couse it will work much faster.

Because how are the batteries connected in series. This is 10S battery pack. And the charging connections are not the same there is a difference. If you charge it on one side you will charge only 5 battery groups in series so this will be 5S. If you look at batt. Pack you will see in total 5 segments with 6 battery together. In this one are 3 with minus terminal on one side and 3 with plus terminal on one side. This one pack is 2S. So if you charge the same on one side you are 50% done and this will be 5S shared so you need to do the same on the other side to charge other 5S pack. Ok ? )

@@trebor1477 Thank you for taking your time to answer me. I will investigate it further. I still don’t quite understand it, but I will find out when I will be working on it myself. 🙏

@@steencd yust do it as it's in the video 👍

Because of Octopi and camera

Hi. Sorry i did sell my tinyhawk2.

www.thingiverse.com/thing:2567757

Yes i really enjoyed modifying it. I was thinking to make it RGB to print in colors . Well the print quality is allso great now. The very first upgrade on this printer must be printing head, feet for heating bed and 8mm sliding bearing are terrible.

I think it is only one profile or maybe 2 for 1s and 2s. Look bardwell video how to set up transmitter switch for this

@@trebor1477 I saw 3 pid profiles when loading up your click?

@@lander42 There are two but third is default

Save your configuration diff all in CLI. And try this. Maybe you will need some new PID settings

E pa ti samo slobodno pitaj. Pozdrav iz Slovenije.

@@trebor1477 pozdrav iz Slovenije (Jesenice) za Sloveniju ;)

@@TheHuseinbasic dobra 🤣 A si mogoče sprobal pide?

@@trebor1477 nisam z cajtem ... bom probal.... javim

use nimh mode a few seconds, so it bump battery a little bit enough to enable liPO mode to recognise

@@eugenyperepelyatnikov4162 Should I be using DC or AC? or does it technically matter?

@@Five7weezy what do you mean? in iMax b6 if it want to charge in LiON mode. select NiMH mode for a few seconds, it will bump voltage of a sell a bit and then select LiON mode again and charge like normal

@@eugenyperepelyatnikov4162 sorry that was a seperate question. I was just wondering if the B6 should be charging the battery via DC charge or AC charge. As my balancer has the option for either. But I will do what you said and let you know how it goes. :)

Try to measure the voltage of each segment of the battery pack

​@@trebor1477 Hi All appear to be between 3.9 & 4.0 v

@@harwoods11 All 10S points mesured?

@@trebor1477 Yep.. Battery is fully charged..all cells..giving me 40volts. Through BMS I get 20 volts. Fitted another bms but same issue. 4 red led flashes

@@harwoods11 I have exactly same problem.have you fixed your battery?

I'm on bluejay 48kHz. I had the same problems as you do. Just try my dump and report back.

@@trebor1477 So you disabled rpm filter by intention? What are your flight times?

@@0xphk yes i did 😁. Flight time? I don't remember correctly maybe 6 min but the battery is a little too heavy it is 2s 620mah

@@0xphk i. Did you try it? if you got something better please share :)

@@trebor1477 Not yet but planned, no spare time before the weekend.

Yes it can be used, but this new display is so much better. But changing from 8bit to 32bit and better motor drivers is huge step forward. On 8bit bord there is no enugh space for Marlin extensions. On SKR 1.4T you can enable all options you want 👍

Depends what you want to do. If you need bigger bed and you want to mod it then Anet A8+ but out of the box Ender 3 V2 is better. But after you do BLV mod Anet is great and i will not replace it. I learn a loot transforming my printer 😁

IMAX B6

Hi. It is probably the same. I charge them with low current and stop at 3.5V on pack. I used volt meter to check it.

I'm glad to help man. Please click subscribe button 👍😁

If this is mesured at end off black connector then no. You need around 42V when it is full. And 38V vhen empty. If you got blinking red led try chraging cels as i did.

@@trebor1477 I’m getting 36v from every connector however from the main red and black connected to the bms I only get 3v

@@meco3215 what is LED colour? Blinking red or blinking blue?

@@trebor1477 4 blinking red

@@meco3215 battery is too low discharget. Do as i did in video.

No. I prited all parts from PTEG

Try to charge it as i did. Battery is deep disscharged.

@@trebor1477 ok thanks

Same issue here with 4 red blinks om BMS. Each cell was about 2 volt. I have now charged each cell to ~4 volt each. Still the battery contact to BMS just shows 3.4volt, it was the same before Charging each cell..😢

​@@BlommanSwedhello I have the same problem, were you able to fix it?

@@macromaker Yes i fixad it. Just charge the cells more. I Think i charges about 4volt per cells. Now the original charger doing the Charging fine.

Hi. In our local shop. But you can find it on banggood allso.

Yes you can, but you must do a lot of changes in marlin config files