Відео

those 2 black plugs at 2:18 cover glass guideblocks. if all you need are minor adjustments you can raise/lower the front/back with whatever sized torx and skip all the in/out adjustments. if you need in/out adjustment you have to adjust the mounting studs for the regulator. you can see one in your video and the other is hiding behind the door speaker so you'd have to take the door speaker off to get to the front one.

What screw i need to turn for Angle fitting? as mine is hitting the door pilar when closing

Very helpful video. My door was driving me crazy because there was a clicking sound that I would hear anytime driving over bumps. I took the panel apart so many times trying to find it. Then I noticed that the passenger side window was sitting much higher than the driver side. So I followed your video, lowered the glass; and now the sound is gone. Seems that since the glass was sitting so high that it was tapping against something inside of the door.

подскажите, какой размер колец в цилиндры

Thanks !!!

Thanks for sharing I’ll try this on my model 3 this weekend I’m hearing wind noice on the fwy 😤

You removed the the aftermarket door seals? What happened? I added them to my 2022 Model 3 and they reduced the noise of going through puddles and slushy snow A TON. Didn't help much with high speed noise. EDIT: Great videos. Thank you! New subscriber.

You would think Tesla tests for wind noise. Bastards need to pressure test!

Just bought a used 2022 M3. I took my first long road trip and windy city! I was going crazy! I almost bought a rubber seal, but let me try this first. Thanks!

if my window squeeks and rattles while going over bumps if the car is cold but is fine one the car has been in the hot sun do you reckon tighten the window by 1 turn?

so if I wanted to pull the bottom of the window in, in the back, I would tighten the one furthest from the front correct?

Thank you very much for sharing your knowledge.

Shouldnt you need to hold the nut with a wrench so the outer nut doesnt move while using an allen wrench to turn the inner sleeve? When i turn with the allen wrench the entire mechanism moves and didnt help my window noise at the top.

Did you adjust up and down or just side to side?

Would this possibly help with wind noise? I’ve already tried adjusting the glass closer to the seal

Thanks man

is it the same process for rear?

Thanks to this video I was FINALLY able to solve my wind noise problem! Didn’t have to remove speaker because just adjusting the rear of the glass did the trick since all my wind noise from coming from near the B pillar

Is this a fix for window noise? If I nudged it up a bit

I just did this on my 2023 Model 3, I only had to adjust the rear one, so I didn't even take the speaker out. It fixed the wind noise completely and the glass is flush with the B pillar now.

Two attempts by Tesla Service and they couldn’t fix my car. Watched this video and had it fixed in under an hour. Thanks dude! 👍

Great video! It was a big help

Thanks for the install demo,Great boating to you and yours.

Thanks for the detailed video. It helped me adjust my window properly.

Is there any way to get the bottom of the window closer to the vehicle, or just the tilt?

Где можно купить...

Great video! Based on this, I did a successful seal replacement. Many thanks!

thanks

You have a link to the hitch mount that fits the harbor freight flagpole?

Thanks for taking the time to show us the adjusted process!! I was envisioning my first cylinder to be much like yours having never seen any of the internal workings!! Much appreciated!

Thank you for the video, it was very helpful. I did this on my Sept 2021 Tesla Model 3. The Torx screw is T30 now. Also, I found 2 turns to be too much. If there's too much friction between the window and the window gasket - pinch detection kicks in. For me, a half turn helped. You can definitely see the window putting more pressure on the window gasket.

Great video pal. I just received my new o rings and thanks to your video, I will be doing this myself soon. You just saved me from having someone replace the actuators with new ones. Thank you very much

How much you paid for this car? And they have so many issue and where is the warranty for?

Ich finde nirgendwo angaben zu den Maßen der O-Ringe. Kann mir da jemand was dazu sagen. Ich möchte ungerne erst ausbauen und dann die passenden Ringe kaufen gehen. I can't find any information about the dimensions of the O-rings anywhere. Can someone tell me something about that. I don't want to remove it first and then go buy the right rings.

You Sir, are a HERO with no CAPE.

Top tip. If you are trying to adjust your windows. Don't reinstall the door panel until you have taken the car back on the road to see if the wind noise is gone and readjust as needed. The wind noise on my 2023 model 3 was at the b-pillar both front and rear glass. Use a dollar bill to slide between the glass and the seal to check where the gaps are at

Great video. Thanks so much. Inside the actuator it seems to have a second place for 2 o rings. That's what I did, I put 2. I haven't tried it yet. Do you think this will create a problem or really solves the leak problem?

Hi, thanks for the video, do you know the sizes of these o-rings?

Very tempted to try, my wind noise by driver ear gets worse if I push window out with thumb while driving. However, given that I never get water spray inside from high pressure laser free car washes, I am wondering if this is even worth trying.

So, how did this setup workout for you? I’m about to run the same setup for N. AZ camping and interested in the connectivity level around trees with the flagpole. Thanks!!

Hey thank you! Worked for me. The only thing is that mine is a 2018 Model 3 LR and it wasn't a 27 Torx it was a #30. Cheers!

Thanks! Did you use a specific adapter to connect dishy to the flagpole?

Nice video. You didn’t mention the specific pole you bought and the adapter from the pole to dishy - appreciate any info here

Great information. Thanks.

Nice video. We've got a reflection as well and I'm trying to figure out the best way to pole mount mine. I have a Flag Pole Buddy for my flag already on the ladder, so I don't necessarily want to mount it on the ladder. You also may find that you don't need all that height. You can cut down on the height to add stability to the dish. This may be an option for me. Thanks for the suggestion.

Good help😎🇨🇦🇨🇦🇨🇦

Que líquido hidráulico lleva?

Donde se puede comprar las juntas toricas de repuesto?

Nice video, thanks