Відео

Thank you for the comment, an E1 error or a PCB error, take the PCB in for repair

Thank you for the comment, an E1 error is a PCB error, take PCB in for repair

Thank you for the comment, you should be looking for a standalone ET receiver not programming to the D5Evo PCB, once you find the receiver, please check my video on programming to a ET receiver... ua-cam.com/video/3gYdM8pykzk/v-deo.html

Much appreciated Nick. That is a quick response. I will let you know if I get it right. ​@nicksandtrickssa

No problem

Thank you for the comment, much appreciated

Thank you for the comment, much appreciated 👍

@@Tbaz777 thank you for the comment, unfortunately not, you would need to get a 1ch Nova receiver to make that remote work

@@KennyManda thank you for the comment, Apologies, this video was made before I did voice overs, but thank you still

That is it yes

Thank you for the comment, much appreciated

Thank you for your comment. Please watch ua-cam.com/video/0IK7CKwFOio/v-deo.html made specifically for this reason

Thank you for the comment, short answer is no, but you can try changing the force settings, but be careful, the higher the force the higher the resistance needed to stop the door...

Thank you for the comment, try using a piece of copper wire to bridge the pins, then watch the Rx lite.

Thank you for the comment, much appreciated

Thank you for the comment, on a ET 500 with no beeping is difficult as the board uses beep codes to communicate, take a jumper and put it in place of the green wire (door release) and see if the board beeps

@@nicksandtrickssa you are a life saver, thanks man, I placed the jumper on it beeps and the gate is working again, does this mean my door release is faulty? I left the jumper on in the mean time

@@TheLadiesmanG what you can do is bend the pins, maybe the connector not making good contact, having the jumper there is a problem if you ever work on the gate as it will be on all the time even with the door open

@@nicksandtrickssa okay I will do that, thanks again

@@TheLadiesmanG a like and sub would be appreciated

Thank you for the comment, much appreciated

Thank you for the comment

Thank you for the comment

Apologies for the late response, thank you so much for the comment.

It will unfortunately remove all, getting a new remote might also not be an option as some of the new NICE remotes do not work with the DC blue digital motors

Thank you for the comment, you have to reset the receiver and start over, Remove all power. Short middle and BT receiver pins and place a wire short between terminal 3 and 4 (C + BT ) of connector block(or press and hold test button “D”) Re-apply power. Buzzer will begin 1 second beeps. When buzzer emits 1 continuous tone remove shorts and power. Re-apply mains power first then battery power.

@@nicksandtrickssa Thanks, will this delete all remotes? And I have the ET DC Blue advanced... Is it the same process?

Thank you for the comment, does the closed limit light turn on when reaching the end, normally it does that beeping when it cannot find the magnet at the end of a run... Turn the motor to manual, then close all the way... Look for the brown and white wires and see if the LC led is lit, then open all the way and check for the LO led

In the closed position, put the 4 dip switch to on, put the Progj jumper on, press set button 1x, the gate will pause but then open and close, it will buzz when complete, remove Progj, turn dip switch 4 to off. The crawl distance will be less ne, you cannot turn it off

It does crawl at the end of opening and closing. I'm glad you like the videos, please share and sub to the Chanel it helps others find the videos as well

Thank you for the comment, good to know my video is informative

Thank you for the comment, it would appear that either the gearbox or PCB if faulty, but it could also be a flat battery, try a fresh battery first

Thank you for the comment, when you say nonstop, what exactly does it do? And please describe the non stop beeping

@@nicksandtrickssa The gate is not working at all, and the motor has a continuous beeeeeeeeeeeeeeeeeeeeeeeeeeeep Not beep, beep, beep....... Lol, hope you understand

@@h.product5153 you mean a continuous tone, not beep, the beep codes work per second, not continuous... Power it down and up again. If it continues then have a technician take it to a repair centre

@@nicksandtrickssa thanks for the information, I'm in Parow Cape Town, are you a technician, if so, where about are you. Thank you again, much appreciated

Thank you for the comment, you need 2 channels, 2 buttons and 2 zone available on the alarm to do 2 functions

Thank you for the comment Bryce, that is a blown FET on the board, you need to take the board in for repair, behind the motor fuse is the effected FET

Ok thanks, that would explain why the motor direction changed and I had to reverse the motor leads into the motor terminals?

Thank you for the comment, a like and sub would be great

Thank you for the comment, I will have to check, in order delete remotes, you need a master remote I believe, but have to double check

Thank you for the comment Craig, does it happen when it's hot outside or just randomly? If it only occur when it's hot or when the motor has been opened a few times it can be dry joints on the control card

Thank you for the comment, a like and sub would be great

Thank you for the comment, you can only adjust the door by doing the completed limit setup, it will flash P until you complete the limit set and the remotes will also only work once the motor confirms limit setup completed

Thank you so much... It is working now after your comment... Much appreciated

@@azizarichards1002 no problem, a like and sub to the Chanel would be greatly appreciated

Thank you for the comment, you mean manually opening the door? There should be a red string on the draw bar to pull and you can open it manually

Thank you for the comment, turn the force dial clockwise, gearbox or inner motor could be going

Thank you for the comment, after it does the limit setup it will go back to flashing P, then you press exit 2x. It will then go to standby mode and that is when you test it with the remote. Where are you getting stuck?

Thank you for the comment Jacob, please take it to the nearest re-seller to have it sent to NICE SA for repair, it's a PCB issue that has to be fixed, or purchase a new board

Thank you for the comment, origon not found can be a doss/loom error. When you move the gate past the magnet it should tell you it moved past the origin marker, if it does the you might have a PCB error

Thank you for the comment, it depends on which DC blue digital you have 4 buttons-no pins, or 3 buttons and 3 pins

It has 3 buttons but I’m uncertain how many pins I have. Can you tell me what I can do if I have either one of those two and I want to reset the code so it’s only paired with a remote that I’ve paired.

Gather all your remotes as you will be resetting the receiver Power down the motor head completely There is 3 pins on the board it will say BT and Lt with a center pin Get a piece of wire and bridge all 3 pins Return power and watch the Rx led or count to 15 Remove power Remove bridge Return power and test If it did not work try again until a working remote stops working Then program all the remotes again

Thank you!!! You undoubtedly saved me and my family! Thank you very much!

Thank you for the comment, please email info@rsec.co.za for pricing

Thank you for the comment, the pedestrian is on the motor side, you will need an additional receiver

Thank you for the comment, if you have the remote yes, if you do not have the remote, do the following ua-cam.com/video/sjl5Z9lZQKQ/v-deo.html

thank you for the comment, please like share and subscribe for more content like this

thank you for the comment, please see ua-cam.com/video/8fwuxNGJt7g/v-deo.html it will help you with the error

Thank you for the comment, hold the set button, to go into programming

@@nicksandtrickssa so i did that i programmed "b" to the blue button and it showed me "1" now when i get back to standby when i press the blue button it just shows me "p" and it starts beeping

@@user-md5xx8up5j you have to complete the setup, before you can use the remote, do all the steps as it is in the video

@@nicksandtrickssa i just followed the instructions and im where you say i should close the door on the blue thingy so when the door closes it flashes "E" and "1"

@@user-md5xx8up5j a E1 error is a faulty PCB, motor needs to go in for repair

Thank you for the comment Malcolm, I dnt see the point of not cover over the noise of a busy cape town main road with shouting in the back ground also, I thought I'd atleast make it a little more bearable with music. Apologies. Please see ua-cam.com/video/0IK7CKwFOio/v-deo.html Update video

Thank you for the comment, there is a nut in the front of the drawbar, that can be tightened

Thank you for the comment, does it not close during the setup or after?

Thank you for the comment Dreshni, there should be a red string hanging from the middle of the draw bar, pull it and you can manually open and close the door, be careful tho

Thank you for the comment, if 15 beeps is motor fault, but it can be a sticky relay on the board, if you turn the motor wires around to make it open first, check if it moves, if not then the relay faulty

@@nicksandtrickssa thanks will try that