Відео

Won`t work properly like that because HV just leaking like gas, you will need perfect insulation...

I love this. Do you sell them? Also, what about having one, that has a small gear you could turn, or a crank to quick charge the cap

From where did you get that fpv? Please

I just watched your first video on this generator. Yes I under how the flux gate generator works. If that's all that you're demonstrating you done a good job. If you want to compare efficiency you need to measure the flux gate across a non-reactive resistance load. Don't use any LED lights or incandescent filament lights. Use an actual large enough resistance that can both handle the current and the heat without overheating or burning up. What you want to do is find a sweet spot load that allows you to have the highest voltage reading measured across the load then with the same setup take the meter and read the current and multiply the current X the voltage. Now do the same with the power supply current and voltage. You can now compare the power consumption's against each other. What are the power calculations of your motor consumption with and without driving the flux gate generator? In other words what is the power cost of just physically spinning up the flux gate generator?

If you're measuring 70 volts across a load that is drawing 2 amps through it then yes you will have a power that calculates out to a reasonably true 140 watts... In the video it appears like you're using a Fluke 179 or something in that model number family so that would be a TRUE RMS meter which means you can read non-standard wave forms and it will give you accurate voltage and even current readings even on non-standard wave forms so yes you could use it to measure raw non-standard voltage and current wave forms across a non-reactive resistive load and do the calculations with accuracy. If you're converting your voltage over to DC then yes that will even make the job easier to do the calculations. Are you reading a DC current with your mechanical meter? Is this current being measured across a load or are you doing a dead short with your generator directly across the ammeter? If you're getting your current reading by shorting the ammeter directly across the generator output that will show you the maximum current you can get out of the generator under a dead short condition but you cannot take a reading across a dead short and then use a open unloaded DC or AC voltage reading to do your power calculations with. It doesn't work that way. You have to be reading the 70 volts under a load condition or better yet, across an actual load and then read the current that is passing through the same load. If you are doing it any differently then you will be way off on the power calculations. It appears from the video that you are reading your current under a dead short condition then you are reading your voltage open and not under a load. If I'm mistaken then my bad.

Could you give me any tips/links on what to buy for a tank fpv setup?

Are those 3 ferrite rods over each coil of the commutator?

Looks good! When will offer units?

You may consider charging a 12v battery with the output. That provides an easy way to measure output power and calculate overall efficiency. In any case, great design and fabrication. These generators are certainly unconventional.

I want to buy this

Did you check the Rpm difference of the motor for the more efficient mode?

0:19 Not BEDINI. And remember: AI audio: Instant Thumb Down.

thats very interesting thanks

Nice build! Try driving the motor with just a DC source, not a pulse configuration. When you short the coils it should speed up and power draw should decrease. Make sure the coils are wound properly. The patent description is backwards.. you have to reverse it.

Where did you buy the frequency generator???

Listening to an AI is a bit annoying...

Looks like the perfect system Nice work bro !

This is exactly what I needed. Thank you

Nice find

Awesome Thanks for sharing

❤

I'm curious if the motor performance is the same or better after the scavenger circuit is introduced. The purpose of any scavenging should be the improvement of the overall power consumption of the system and not to harm the main functionality, in this case, motor performance.

I was just going to ask you if you seen the plasma channel episode 😅😂

Nice demo bro !

Awesome video! You are doing great work my good man! I can't wait to see what you have planed next 💯⚡️

Very interesting

Is it just me... or does this guy and EVERYTHING INSIDE ME sound like one and the same?? lol.. Well.. if it is or isnt, Both seem to be going down the right road! Keep up the good work bro! Kudos!

Cut the bullshit with big words and sensationalism. Just speak like a normal human being. Thumbs down and I am out.

congrats you made a nothing machine

what can i do with a 2khz output? because i have that, is it good for something?

where did you get your laser cutting done?

Cool circuit! And the ai voice, wait thats not you?

You and kenergy are the same person

❤

Nice work bro !

looks good bro!

Yes please.

Definitely interested in the PWM once you get settled in your new digs! 👍

How meny volteg in put to grnarator

I am using 9V supply for mosfet, but the copper coil 10-15 windings 2 inches dia doesnt generate electronmagnetic field. What is the suppy i could use volts amps to power this up, the way you make dance the magnet. Rest pwm provides the freq which is all good.

I just blew up one of those PWM boards trying to drive a pulse laser diode. I didn’t know about the MOS adapter board. Just ordered a 5 pack from Amazon. Thanks for the info.

2cell battery powered?

Good to see you back

Good Stuff

How many volts did you use for the power supply? I'm building one for my Chladni Plate right now....

I think if you make those changes from below you will have a self runner, ou device.

During recent research, I've discovered that placing even a few strands of iron (like construction wire) as a core greatly improves induction into coils without causing drag as coils are parallel to rotating magnets...ua-cam.com/users/shortsjyK1Kml2jck

is it full wave?

Bedini has a video and explains why he does not use powerful neodymium magnets but uses the ones he uses.

Order kaise kre kon si site se