Відео

Thanks for watching!

No probs, thank you!

Thanks!

@mwjoinery de rien c'est avec plaisir

Thank you! They are very nice and simple to make but end up really strong and sturdy👍🏼

I can’t remember exactly because I bought that timber for a different project ages ago but would say it was around £50-£60. Thanks for watching

Yeah that could definitely work! Because I had a few to do I like to set my track saw up and do as much cutting as I can outside. If it was just the odd one I think the multitool could be a good idea! Thanks for watching

Thank you! Appreciate the comment😁👍🏼

You can fit a kitchen in 5 mins? That’s impressive! Only joking, it is actually a quick way of fitting end panels it just looks long in the video because I had to make the templates. If you keep the scribe blocks it takes no time at all to do it👍🏼

Thank you👍🏼👍🏼

Yeah that is a good point. I didn’t really think about it to be honest until a few people commented on here. I didn’t seal the cut edge with a bit of pva and also sealed it so that should at least help avoid any damage. I get where you are coming from though. Thanks for the comment👍🏼

You’re welcome! Thank you for watching

Yeah that’s definitely worth doing on floors and walls that are well out! Thank you for watching and commenting👍🏼

Thank you!😁👍🏼

Thank you! Appreciate the comment😁

Thank you, probably a love it/hate it thing but when I was doing it I thought it was a lot more boring to watch without music. Thank you for mentioning it and I might try without next time👍🏼

Thank you!👍🏼

Doing it this way doesn’t matter if the floor or walls are level. It scribes it to them

@mwjoinery well you can't use the guide for the saw if the walls or floor needs scribing that's what I meant

Yeah I cut it as close to the line with that and then just sand to the line to follow any contours

No problem at all, Thank you very much for the super thanks!😁😁👍🏼

Thanks a lot!👍🏼 not sure of the exact weight bit if it’s made to all fit together when it’s packed up like this one it does weigh a fair bit. The one I keep at work doesn’t pack away all as one and I find that a lot easier to carry. I have thought about cutting out some of the material on the legs to reduce the weight a bit but I’m not sure how much that will affect the strength of the bench. Thanks again😁

They are very good!👍🏼

Never thought of that but it’s a good idea👍🏼 Thanks for watching

Thank you for the comment! It is very easy once you get your head round it! Just make sure to seal the bottom as I forgot to mention that in the vid. Thanks again

That’s a fair point but what do you do if the floor is out of level like this one was? If it was square I would just cut the top but if it is out of square I do it this way. I do seal the bottom of it to help reduce the chance of any damage

Hi, I do agree that is a downside to this method but when the floor is out of level there isn’t many ways around it. I did forget to mention in the video that I seal the bottom and also finished it off with a bead of silicone. Thank you for watching

No worries, Thank you!

Thank you!😁I haven’t got my van anymore unfortunately and I can’t remember which one I used but it will have been 18mm (3/4”) or 12mm (1/2”). Either of them thicknesses would do the job well👍🏼

Thanks very much.

Thank you very much!👍🏼 to be honest with you I just stuck it down with the adhesive. I left my van in the sun one day opened the doors and one side had warped and risen so I would definitely recommend screwing it! I can’t remember exactly what size screws I used but I just used the smallest I could get away with and only screwed it into the plastic rather than going into any metalwork. I struggled to find any diagrams or anything as to where any cables might have been so I was very cautious. Thanks again😁

Thank you!!👍🏼

Thank you! really appreciate the comment! And thank you for letting me know. These are just tools I use all of the time, the affiliate thing was an afterthought so I should have probably looked into how to set it up better😆 will have a look into it tomorrow! As for the driver, I have one in my usual toolbag but that was at work so I just used anything I could find laying around in my garage. That was the closest I could find😆 well spotted though!😁👍🏼

No worries. Thanks for the comment👍🏼

Appreciate it thank you😆👍🏼

Yeah it’s a very useful technique in my opinion! Thanks for watching and commenting👍🏼👍🏼

It is a trend v groove bit. Any v groove bit will do really it’s just handy to have one that has a small flat on the top of the cutter so the bit what you are engraving has a flat bottom if that makes any sense. I am out at the minute but can tell you the exact bit I use when I get home if you want?

He CLEARLY stated what bit to use. This is WAY over your head.

Thank you very much! I’m sure you could do it with a little bit of practice! Yeah, if you master that it makes it so much easier. You wouldn’t believe the difference a sharp chisel makes. It sounds silly but a sharp chisel is also a lot less dangerous. I always nearly end up injuring myself using blunt chisels just because of how awkward it makes everything😆 thanks again!😁👍🏼

Hi, thank you very much! I do appreciate it! It is not something I’ve really done before but my spade bits are a bit blunt and didn’t want to make a mess of the mortices. The mortices went all the way through so they can be seen on the outside and I just wanted to make sure I had a neat square before risking it with the spade bit😁👍🏼

Yeah that’s a good idea! Might have to give that one a try👍🏼👍🏼

When you are doing it like this it doesn’t really matter. Just line the end panel up to the cabinet before fitting and it will be bigger than the cabinet. For example let’s say it is 20mm bigger than the cabinet. In this case you would need something bigger than 20mm. Let’s say you use some 30mm timber to clamp on top of the panel and lift it off the ground. You would need to use a scribe block the exact same size (30mm). This would lift the end panel off of the floor 10mm once it is hooked on the unit. Then you use your 30mm scribe block to mark a line. As the end panel is off the ground 10mm the mark will be 20mm from the bottom of the panel. Cut this and unclamp the piece and it should finish level with the top once it’s in place. I might have made it even more confusing but hopefully that makes a bit of sense?😆 if not, let me know and I will try explain it better. Thank you for watching👍🏼

@@mwjoinery thanks for reply mate. I think I get it. Watched it a couple more times. Reallly nice. Will practice it soon 👍🏻

Awesome, thank you and just leave a comment if you have any more questions or struggle and I’ll try help😁👍🏼

Thank you!😁👍🏼

@@mwjoinery u r welcome and thanks

There are a few ways to do that really. You can either oversize the piece, do your scribe and then mark on a level line where you want your straight cut and cut it with something like a track saw. Or the way I do it mainly is overhang the bit you want to scribe lets say 40mm for example and level it up. Then if you clamp it in place, set your scribe tool to 40mm and cut it out. The board should slide back 40mm and finish flush on the front edge. Hope this helps? If not let me know and I can try to answer it better? Thank you for watching👍🏼

@@mwjoinery Actually, that helps a lot. Thanks for the reply!

No worries at all. Thanks

No problem! Thank you for watching and for the comment😁

@@DorothyChicken-j5b hi, no that shouldn’t matter it just needs to be enough so that you can hook the cabinet onto the top of the unit. I would say anything from an in to 2 inch is ideal. It’s the depth of them that is the critical measurement and they need to be the exact same as each other. Thank you for watching!

@mwjoinery OK. So as long as both pieces are the same and you book them on so they're level, the scribe should be good? Thnx for you reply.

Yeah, like at the start of my video you just have to offer the end panel up to the carcass and it will overhang it at the top. Your piece needs to be bigger than that overhang and both the exact same size as each other. If it is less the overhang when you try and hook it on it won’t raise the panel up off the floor if that makes any sense? And it’s no worries I’m happy to help as much as I can so feel free to ask👍🏼

It probably doesn’t show easy they are to make in the video so I apologise for that but if you manage to get one made it makes cutting wedges so easy and can just save the jig and use it again and again

@@mwjoinery No need to apologize. Sorry, I am just being cranky. Lots of UA-cam videos have clickbait headlines like This will amaze you and world's fastest. I am laying cedar in a sauna on a sloped floor with a drain in the middle and going mad trying to level it with varying wedges sizes and lengths.

Haha yeah that’s no probs I understand. That does sound like a nightmare tbf😆 hope you have managed to sort it?😆🤞🏼

I like to finish them flush personally but probably a preference thing👍🏼