Відео

That's just lighting. What about when it doesn't stay lit?

Please HELP my Qtip head FELL OFF INSIDE that area & STILL WON'T LIGHT 1wk later😢

There is nothing new in the world. I have been using this method for marking stair strings for 50 years.

I almost bought another one ..this worked great thank you.

Thanks man, this worked for me. Mine was sitting in the basement over the summer

Great video. Please remake it without the background music. Or make the background music waaaaaay lower.

*But what about the width! I need to make mines steep since it's a mini house stairway*

Thank you so much, this fixed my portable buddy!

Mine is brand new and the qtip didn't work. I wish I had seen all these problems with mr heater before I bought mine. It is going back today. Second trip to the store to address a problem with this heater. I wish I knew the brand of the old camping heater I used decades ago. I never had a problem. I see these mr heater products all over and wrongly assumed they must be good

Thank you so much I was just getting ready to order another one

Alas, this did not work for me and I had such high hopes for it. The Buddy would not do anything more than spark with a 1 pound bottle or hooked to a 20 pound tank.

I rented a professional underground locator, well worth it, easy to use. I located water lines and gas li es and one storm drain

You measure down 7 inches for your board mark so do you have 2 x 7 board you are using my husband and I are so confused on some of this as we’re not real carpenters we are using two by 12s so we figured we need five stairs because we’re doing 5 inch rise but my husband is confused on the part that attaches to the deck. How do you know to get that cut and your board was already marked with the triangle on it so we didn’t understand how you got the triangle cause you didn’t show the bottom mark on your triangle. You just sold 7 inch to 10 inch and then go straight down from the 10 inch to the bottom of the boardbut how do you do it with a 2 x 12 can you please explain

Thanks bud, that fixed mine 🙌🙏

But it’s brand new hasn’t had time to get dirty????

Worked for ME! Pilot plugged...

These wire locators are hit and miss. The receiver was nearly deaf .. wouldn’t track past 6” from the transmitter. Returned it.

Thanking you in advance, mine just went out, I’ll get the items I need tomorrow. 🙂

Madd me watch a 30 second ad👎🏻👎🏻👎🏻

Thanks much... Fixed 2 of my Little Buddies!!!

Life saver! Thanks, bud!

So grateful for this tip!

Thank you sir. You taught me about the lever connector and how to pigtail. Ty again.

Hi, when the transmitter is connected to the mains, can its signal also propagate through a 12V power supply or a 5V Usb power supply and be detected on the cable of these power supplies ?

This video saved my sanity. Thank you lol.

It’s just what I needed.

OMG! Works perfectly now. Thanks.

where do you get the mull?

Thank you very much. Thanks to your video, it only cost me one q-tip to fix.

Saved me a headache! Thank you!

Thank you sooooo much 🎉

Worked great, thanks!

Thank You!!!

I was with you up until you said the run will be 10 inches. How did you come up with 10 inches? You never mentioned that in your opening statements. Is that a standard measurement for the depth of a stair tread? Also, how was it determined where on the board to start tracing out the first stringer? Looks like you just arbitrarily chose, what, 4, 6, 7 inches? Thank you.

I purchased a Buddy heater had a markdown Amazon store for $6.00 couldn't get it to light tried what you did solve the problem immediately. Thank you for the helpful hint

This didn't fix mine.i don't know what else to do. Full tanks.

It works better if you staple to the studs and create an air pocket, otherwise is is conducting heat and you are losing most of the benefits

Cutting with a circular saw its normally wise to stand to the left and let the right drop

A true test would be to put the insulated sheet outside in the sun just like the roof and then take a reading of the insulated sheet.... And then compare

Thank you! I fixed mine thanks to you

After not using mine for a couple of years I tried it and the problem was exactly what this video shows. I followed the remedy step by step and it worked great.

Problematic! What counts here is the time it takes for the foil to heat up to the temp of the outside roof. As soon as this has been reached (and this will be relatively fast with thin foil) heat will go in! Or come out. So important here too is the time that process takes and thats why in my country usually very thick insulation is used, up too 15 inches where possible. But sure, even a thin foil is better than nothing.

Just picked up one from Tractor supply stays lit on pilot then goes out on low or high settings…

It worked! Thank you!

For those insisting that 811 will take care of this. This is what I got directly from the local 811 "Any electrical lines past your meter are owned by you, and is your responsibility. These may include power lines running to barns, garages, outdoor lighting, or from your transformer (green box or pedestal) to your home or business. We can only mark up to a meter of underground line if your meter is on a pedestal, and not on your house."

THANKS!!! 👍👍👍 This works!!! I've been trying for days to get mine going, and this was all it took!!! My little buddy is working like new!!!

Running late I'll be doing it

Hi, what is the distance between the transmitter and the point where you drilled the hole ?

Perfect video. Watch this video then did it to mine and it fired up with no trouble. Thank you for this video.

Was this 2x6 or 2x8? Thanks