Відео

GACO brand or Ames Blue Max with Roof Armor ....Miami Dade approved

I don’t understand “reinforcing rafters” and spiking them into an undersized hip? Any thoughts?

Broski's man tht milwaukee hammer is a bitch to mover around compared to chorded 1 or a air powered hammer. Even on tht short ass dolly system its a bitch rolling in and down set stairs.

The comment section never disappoints…so many experts on here lol

Wrap the water right into the header sweet!

How far in under the footer do you dig?😊

So where is the next video mr underpin?

Goodjob

Did you just post the same video you posted 2 years ago?

Jeez, how much does a job like this cost?

All those staples are not necessary.

you can eliminate collar ties and spreading by 'hanging' the rafters off of a ridge beam . not a ridge rafter but a beam calculated to withstand the load. this save time , material and money if the length of the rafters is excessive then simply add two more beams about one third of the way down from the top on each side .

😊

We did for the rest of the job. This was a last minute pour and we couldn’t get a truck in time.

Great video , Would you say it cuts pretty fast ?

Why not use a concrete truck ? Just curious

How to create 1000’s of penetrations in your home by yourself. Guess I wont be buying a del grande home

I didn't learn anything.... except, how to rap... lol!

I just wrapped my entire house in a condom and face mask for safety

dude FORGOT a word in his title. He forgot to put "NOT" right after the "HOW"

Moisture will crumble that particle board sheathing and also the framing where it tapers to nothing. Need to keep a minimum of 2" inches of framing at its lowest taper point, so you will need to raise framing in the front area to do this. Use 5/8" plywood building code approved, felt paper and roll roofing. Roll roofing may only last 5 to 8 years, but its easy to tear off and install new. Flat roofs start leaking, roofing contractor comes out, does some caulking or some sort of sealing, may work for a couple months and new leaks, after probably 400 dollars or so for caulk work. The city of Baltimore should of paid for new roof design on these flat roofs, like a shed roof design, at front roof goes up about 5' feet and rafters take it from there to the back with proper drainage. A shingle style roof.

That won't last. Baltimore Maryland has a lot of row houses that are vacant, roofs caved in. Roof problems i think was the start to these row house shells. Flat roofs rubber roofs were and are expensive and still end up leaking even done by so called pros. Not like a 4-12 pitch roof on a rambler, almost anyone with some handyman skills can install a new roof on a rambler, as long as there are minimum valleys. Even new rubber roofs will crack from the winter and summer heat. Flat roofs are junk even a 1/4" to 12" taper, not enough. Water needs to run from front to rear of building and flow into a large gutter with a downspout at each end, at the bottom get that water as far away from the foundation.

Wrong, collar ties do not keep the walls from bowing out. That’s what rafter ties do. They are two very different member. Collar ties only prevent uplift. I never saw a ridge beam on this roof, meaning the roof is not self supporting. I am an engineer, and this roof is completely wrong. I am shocked an engineer signed off on this.

Nice except he's not using an approved tyvek cap fastener.

Looks like a crap job

Wiggers have become ubiquitous in every walk of life.

That will rot Condensation

I did a one man job today on my 20x20 garage im building. Used roofing nails with the plastic caps. Try hammering those by yourself. Staplers voids Tyveks warranty

Im new to the business what's more Ideal Gas or electric? great content btw.

Lmao staples are the staple😅 water will bead over staple holes unless the staples blow through

Highly recommend using a cap stapler

Do you put any horizontal hydro insulation here on the fundaments?

Ça vaut rien

👌🏼💫

Manufacturer instructions are for this to be a floating subfloor & not screwed down. Also should leave a 1/4” gap between existing walls and a 1” gap between exterior bare concrete or block walls to allow for expansion and contraction. Curious why you are screwing down the panels and butting up against the walls?

I’m preparing to start my basement, if I dig under and then pour concrete sections with rebar will this support the home? I’m planning on doing this in 8 ft sections

This was a total waste of my time.

Wish you could show how air conditioning and heater system would go in a room like this

🤦🏻‍♂️

🔥

And then switch to soprema cause no staples....

Aren't these collar ties a tad to high to be considered rafter ties so how does this ceiling meet code?

What did you spray. What was that stuff

Did anyone notice that's not a roof

Did anyone notice that bottle flip?

Do you do any work or just try to act cool ?

You are awesome bro!

11 months ago? Did you not finish the job?

Do you guys serve the Windsor area or only Toronto?

I’ve never had a contractor say we love the challenge, and we love what we do ?? If in a fairytale land I could find one like this , Your hired , wait , how much per hour ???