Відео

press stop+enter and power up does not bring the calibration screen, what's wrong ?

Why after i start charging the amperes start going down till 0.1 A

ok what you need to do before calibrating is put it on li ion setting in user settings after that go into li ion battery and put everything at 0.1 amp and 6s all options from charge ,balance,discharge and storage so all settings are saved as 6s...go back to main menu.....take your 6s battery where all the batteies are balanced...i prefer 4.15 ...and not 4.20....after that connect them to the imax...after connecting it disconnect power from ac to the imax ...hold both stop and enter....power on the imax....now you see all battery voltages all 6 of them...wait couple seconds and power off imax...now restart and the magic happens...you dont have to do anything.

???? Clone and Fake??? See No Fake.. This is a Clone. Display shows SKYRC iMAX B6.. !!! Fake cannot be calibrated by this Way or even calibrated!!!!

Never but.. Never..leave your batteries connected while turning on your charger...

I’m glad to have found this tutorial, however my power supply only outputs 20 volts. Is there another way to reach the same result? 🇸🇪

Načo tam hrá tá hlasná hudba???????

Either this is not a clone or fake charger, or you somehow managed to flash the original firmware to a clone. (Sky RC on startscreen)

Light the video :)but the sound tracks :(

It turns out, if you set charge/discharge/balance to 6S before calibration, all you need is a good balanced/charged 6S lipo. This thing uses the las setting introduced and uses it during calibration

Dobrý deň, veľká vďaka za tento návod ale vzhľadom k tomu, že nemáme takéto možnosti Vás chcem poprosiť či by ste mi takúto nabíjačku mohli pre môjho syna nakalibrovať ?

btw great video but very difficult to see.

you dont have to switch the negatives of the batteries...1s and 5s keep them both at negative connected...only switch the red wire..you also dont have to reinsert the 6s balance cables...let them stay in...after inserting the power watch the screen and see what hes asking for...if you pushed both dec and ent when its on discharge 5s mode ...it will ask for 5s discharge and not 1s...if discharge was set to say 3s before calibrating ...he will ask for 3s ...so best is use 3s discharge setting at 0.1 A and exit the menu and than do the calibration pushing both dec button and ent....sometimes after this he will ask for 4s...keep watching the screen..follow the instructions.

ok what you need to do before calibrating is put it on li ion setting in user settings after that go into li ion battery and put everything at 0.1 amp and 6s all options from charge ,balance,discharge and storage so all settings are saved as 6s...go back to main menu.....take your 6s battery where all the batteies are balanced...i prefer 4.15 ...and not 4.20....after that connect them to the imax...after connecting it disconnect power from ac to the imax ...hold both stop and enter....power on the imax....now you see all battery voltages all 6 of them...wait couple seconds and power off imax...now restart and the magic happens...you dont have to do anything.

Irritating musik..

where is the old version ?? i want to do it with 18650 cells i dont have resistors nor do i have 25 v

hi why my tester is same but in the menu i dont have ir decoder and backcolor what is the difrent do you know

Ta muzika ? Když to neumíš,tak to nedělej. Vídeo o ničem, muzika vše zničí. Nahrej to znovu bez muziky.

Fantastic video and good English. I have a clone/fake Imax B6 but mine enters to original calibration manu with Desc. + Start on power on but the voltage value is not ok. I correct it but if If add the difference the volt vlaue does not changes and I have to store a very big difference (i.e. I have a battery 18650 with 4.15V with tester, the calibration menu (Des. + Start) shows 4.13V and I have to set +0.11 to see the 4.15V read by charger) I'll try your explanation. Thanks a lot for your video.

strasne video...

ta hudba je tam o nicom..nepocut co rozprava

how u know its fake

Přes ten drát není vidět na displej multimetru.

Přes tu muziku se nedá poslouchat. Tvým vzorem je veřejnoprávní televize?

Music TOO loud.

hello John Black. i have a clone charger imax b6 ac that does not have recalibration. i have been looking about one year now for anyone who has a video that shows how to get it back in the menu. i think your video looks good but i only speak english. do you have this same video in english ?????

super

este provador mide diodo

imax b6 with 6 pin (on top), it means.. could be uploaded firmware..bro??

Had it for over a year

set up easy

i don't know if it has any reset i will try to find out

How can I restore the backcolor? accidentally set the backcolor green and this is confused with the green fonts of the frontcolor, so the screen is all green

krasny video ale nerozumim Vam ani slovo. proc ta hudba vsechno přeřve? slo by to udelat se stisenym klasickym background music ?

I'here to see the cables being plugged in, not to see you playing with buttons!

I bought a higher version ISDS210A . Should have been better but it is locking after few working minutes. It's too annoying.

sory za tu hudbu palec dolu

how to connection

I need only the battery of the remote...i want

How to add remote

I integrated a usb rechargeable 9V battery into mine. It has everything you need inside it and a 3 LED charge indicator (indicates when pressing a button). I reused the battery outer case sticker on the side of the scope to make the LEDs look neat. pg-cdn-a2.datacaciques.com/00/NzI4Mw/18/12/14/v0cj0037lymb2c6z/51e50ddc2a7eb368.jpg

super navod akurat mi nefunguje delic ked ho pripojim k nabijacke.Nezapojeny ma na vsetkych pinoch 4,20 v ale po zapojeni a merani na nabijacke nameram na 2 pinoch 0.9v a 3v netusim preco.Ked pripojim 6s pack tak napatia nameram spravne. Ked sa prepne rezim na lipo 6s charge pred spustenim kalibracie tak nieje treba prepajat vobec nic a vsetko spravi so 6s packom

How does one get their oscope modified to use a battery like this?

Anyone try to clone the remote for the YAM switch? I assume it's 433mhz (not 315mhz) but I couldn't do it, tried two different duplicator remotes and they blinked but wouldn't accept or send the signal to this switch.

Do I understand it correctly? I'm not sure as Czech and polish may differ in meaning sometimes... 1) I have to have well balaned 6S (or 2 times 3S in paralell with balance lead adapting it to be 6S?) with every cell at exactly 4,2V 2) I connect balnace lead to charger not being pluged into power source 3) While pressing enter + stop I switch on power supply 4) Charger remembers input at 6S balance connector as new 4,2V pattern and can be switched off 5) I plug charger into power source without battery connected 6) Within 10s I connect 1S into the balance lead 7) 10sec. after 5) I have to connect 6S instead of 1S 8)ready to go Is it right?

Zdravím, super video. jak se jmenuje song?

Muchas gracias por tu aporte, funciono de maravilla!!

Rubbish Didn’t connect

Could you please use English subtitles?