Відео

Hi, please double check the sealing rubber if installed properly, if yes try to tighten the lock nut slowly until leak is gone. Warning, please dont tight too much or it may crack he quartz glass.

Ah yes, you're correct this is valid recommendation. Im planning to install even just a simple timer relay for the on/off delay.

Leaks or popping out could be caused by overpressure or perhaps the materials used. In my videos, I am still using the same hose for the past 2 years and never had leaks or popping out nor replaced any.

I prefer the Gcash because it is realtime and always works with me with no issues. I have heard that sometimes Maya fails in some cases, but if you received an email confirmation or payment receipt please contest or complain with Maya costumer service.

Yes, for recreation/hobby purposes only. And also need to follow CAAP restrictions.

Yes, you can use bulbs as long as it is below 100 watts.

No problem as long as it is for personal/private use only. 😀

it depends sa size ng uv lamp/s mo. Ok lang if 50-100 watts, pero i suggest for a flowswitch para di uminit masyado and maextend life ng UV lamp gas and coating. But if you have multiple UV lamps, then malakas yan sa kuryente.

S water refilling station po, ano pong dapat n variation, 100w or 260w? S lazada kc may dalawang variations?

Did you ever find a fix? Same thing happening with me

Hi, well that is technically a bit dirty water. The RO can drop 7000 to 500 as it should be but your filters will have a shorter lifespan and needs to be replaced earlier. My recommendation is to add extra pre-filters before your main RO system, with atleast 1 washable mesh filter on first stage, it will save you a lot on maintenance.

Thanks

Glad it was helpful!

Please double check for correct hose line-up, just follow the diagram on my video. If all is correct and water is coming out of RO faucet then, the possible causes could be: tank valve is closed/blocked; or the theres a problem on your tank's bladder/diaphram. Please note that tank will take atleast an hour to charge.

Glad it was helpful!

About 60-80 psi water preasure needed to activate. If you dont have enough pressure, positioning the switch vertical with the flow will help, but will have a risk that it will stay activated. Also try adjusting the sensitivity.

Im glad, It was helpful.😊

Hi, please adjust the sensitivity of the sensor and make sure that it is installed horizontally. If still activated, maybe it is deffective. To confirm function, move flap of flow switch with screw driver while electrical circuit is connected or use multimeter.

And lastly, make sure you reached the minimum line pressure of your flow switch. About 60 to 70 psi.

Yes, but the UV should be on the final stage. Please check my other video to see setup.

Yeah, it has no taste. But we cant tell what are in those 100ppm, so its safer to filter them.

Very much appreciated.

Glad it helped...youre welcome.

Yes, you can use deep well water but the system wont run if your supply pipe is not pressurized. It can be solved by stocking water on a tank supplying to RO filter by gravity.

The power should be in series connection with the main cable.

@@jongpenaranda ok thanks!

Close or control the bypass valve (if installed). But if not, you need to install a restrictor valve on the waste water outlet.

Hi, idont really understand what you mean. But you need to adjust sensitivity of the flowswicth according to the pressure you have.

Hi, could be few reasons. But try to double check if hindi nagkabaliktad ng kabit yung waste water hose at yung clean water hose. Another cause could be a faulty restrictor valve or baka bukas yung bypass valve.

@@jongpenaranda thanks po, ok na gumana na yunh unit.

Hi, thanks for the patronage and for the wonderful comment. Well if you have better recommendations...im all ears.😉

@@jongpenaranda ..........yes of course. Why not installing all of this underneath where you already showed there is space for it. Below the countertop or sink!