Відео

Omg I am so happy that I’m not the only one doing this 😂

Thanks for sharing and also for great tutorial. Putty is great but u could be more productive with MobaXterm SSH to your SBC.

I have the rasolution 2 adaptor (Moza rig) anyone got any idea how to make the adaptor recognize it as a Fanatec?

How can use PS5 peasants get these results

Finally this is the video I needed, may I ask how this build has held up for her?

I tried following your video, but then you came to the core electronics part and then your video became as much use as rubber lips on a woodpecker. Installing rasp pi is a piece of cake, but how do you get the different header on your notepad. How do you set the encoding to utf?

is there loose middle?

Thank you for the guide Do it work on a URVE Pi ?

I’m trying with a rev 3 arduino uno and rev3 motor shield with Noctua NF-F12 iPPC 3000 PWM and I can’t get the fans to fully spin up.

Is it possible to use a DIY FFB steering wheel with PS4 using GimX?

What the best direct drive wheel pedal setup

Does this still work?

Awesome video. After many hrs trying to find a way of doing this your video was super helpful. I did get it working on a pi 3B+. I did want to ask, have you been able to remove all start up text and white screen that shows at Chromium start up. I know before these new OS changes, my arguments use to work to start with a super clean no text, splash etc. Any help would be appreciated. Also, I could not get chromium to look right after install. I had to modify my dash. Resolution would not change on raspi-config. It looks ok but wish I could set to 1280x730 of my screen. Again, great video!

Thank you for the "120mm to 76mm Fan adapter (Threaded)" it's the perfect piece I was looking for! Hoping to get this up and running tomorrow, we'll see if I can find the time, I'm going a slightly different route, at least at first and I'm going to run a motor shield for my Arduino, because I want to be able to use a little more power (amps) to my (different) fans!

WOW! That's exactly what I am searching for! Thank you!! One question: can you actually tilt the keyboard to fix it in a more vertical angle? That would be great!

Steve, would you mind helping me with something, as this is all very new to me,I have just bought a simple setup to use on my PS5 and play seat challenge x, basically I bought 3 of the mini Dayton TT25 8ohm transducers and the Nobsound mini Bluetooth power amplifier with built in sound card which is 2channel and 50w and 4-8ohm. My plan was to have one of the transducers (8ohm) under my pedals, then two transducers a on my seat, but running in parallel which I think then halves the ohms so each transducer would be 4ohm, is this safe to do I don’t want to blow out or destroy anything, any help you can give would be greatly appreciated..👍

Steve I love you lol, I’ve just ordered the transducers and hopefully I will be able to use the 3d printed file I’ll ask my friend if he can print them

Hey! What length did the bar end up being cut to? I don't want to cut mine too short (modifying this for an 18mm carbon fiber tube btw :))

Imagine this in 3D as well as VR

Thanks for sharing your build. I've copied this more or less, but when my PC is off, the fans blow on full power. Was this a problem you had as well or have I done something wrong?

Will this need to be on the pc while using it or can it be by itself

geat quality content bro you deserve a sub to the channel

Has anyone recreated this too?

Hi..im new to this..may i know what model/type of arduino uno should i get? Cos i saw a lot of description for the arduino when googling ie wifirev4/rev 3 etc

@SuperEvenSteven What tools do you use to build the PC? Any fancy screwdrivers or glue I should be aware of.

Please if my SO did this for me I would geek 😭

At no point in time did you show how to install this item. You talked about it throughout the whole video and didn’t go step by step

Thanks for posting.. Very cool.. DMAX

Is the 3d models 5inch display only for adafruit or waveshare display? Or also other 5 inch displays?

If you already have a 12V supply inside by the arudino, you should convert the 12V to 5V with some resistors and run the board off the PSU. Instead of increasing the draw on the USB cable.

Unfortunately the case was out of stock when I checked but they don’t know when it’ll be bad in stock sadly

but there's no wind when you're in tintop mx5

Hello, first of all thanks for sharing this video! You wrote: "I use Simhub dashboard and apply speed curving to each fan so the fan's RPM speed adjusts with both the speed and direction the car is moving." Is there a chance to make this work on a console (i.e. PÜlaystation 4) as well using Simhub? I share the Gran Turismo 7 telemetric data already over my local network to a seperate PC for my motion system. So I guess, in general it should be possible, right?

Hi SuperEvenSteven. I have just bought the same fans and wonder if I am correct in assuming the yellow cable is positive, black negative and blue for the fan header, the green is not used??

Hello, if you want to replace the racing instrument panel with a new one, how do you do it?

Thank you so much for including links! Nice build!

That’s so sweet of you and is your wife still playing ❤ My hubby is going to order the parts next week I can’t wait

Wow she's blessed

Hi! Would a 12V 2A power supply work or does it need to be 1.5?

quick question. How did you mount the two fans in the front?

Does this work for unsupported pedals

Thank you for sharing. I used your design which worked well. Initially had issue with the Ardunio board then realised I was missing the driver. Smooth sailing from there. Looks good and work well.

why did you use 2 transducers oppose to one?

Thanks.. in your screenshot (you go fast) of Shakeit PWM Fans outputs, do you have the PWM output on/off relay pin checked or NOT checked? Also, have like yours PWM Output min set to 0, but the fan still runs slow/ not 100% off.. Thanks

I'm pretty much a cc addict at this point will this pc still work even after a year and can you continue to upgrade the parts because i'm trying to build a gaming pc and not buy a pre built one. can i also play stardew valley with mods on this.🤔

Sorry if I missed it. Evrything looks fun and easy, but no 3D printer. Whats the best way to bid that out? (For wind tube adapters)?

What trackpad do you use?

Hmmm wondering if this would work on a Playseat Trophy cause this is EXACTLY what Ive been looking for.

I wondering if the computer can play the game on ultra and maximum settings in native 4K with no mods. I also wonder what is the native resolution of the game since I am going to build a computer to play this game.

does a cp2102 work as well?