Відео

hello sir, @ 3:01, what is that 1015 device? what does it do? TIA.☺️

Why all of you making 5v??? How to get 9v Adaptive Fast Charging?

Nice work... Thank you.

Constant refresher courses like this help me through my apparent learning disability on circuits.

Thanks for sharing! Would you recommend any reasonably priced power supply with identical specs and better reliability?

Muito obrigado por passar seu conhecimento sobre isto, que Deus vos abençoe!

Gravity Falls opening at 0:46 anyone?

Excellent video. I like it when you show your difficulties, it's much more useful than videos that pretend that everything is easy.

Why sever?

That Fake

Link isnt active now

Not Working

Sand me Link

Where is the url

Mine just failed, i took it apart and the chip by D4, by the charging connector melted :<

thankyou you really help me

nice bro. thanks so much👍

The usb type c module still works, but cannot be connected to new phone. I make one, the xiaomi mi5 still some time use quick charge, the mi mix2s can not be connected at all. But i dont know this mod would work

Sever first before doing the 2nd update of the video right?

you can send me the video sense it got tooken down

Ugh, that copper grounding ring hit the floor for me, and 10 mins later I still haven't found it. Great video though, thanks for showing where it goes.

so if i just use USB-C to USB-A(usb2.0) charge+data cable without any modified to the breakout board will ut stil work?

How can measure current

thank you, it worked

I wish USB C was sized as USB A then each user could "do something" and it's getting popular now with visible pads.

It looks like you only added the 5.1K resistor to one of the CC pins. Doing this will cause a USB-C to USB-C cable to work in one orientation but will not work when the connector is flipped 180deg. C to C cables only have one CC wire which allows for power negotiation as well as for determining connector orientation by observing which CC pin has a connection and which is open. You need to add a 5.1k to both CC1 and CC2, or you can also short CC1 and CC2 together, then use one 5.1k to ground. Shorting the CC pins is not normally done but in a simple power application like this, it's not a problem. I realize this video is a couple years old now, but thought that explanation may help someone who is confused by this.

can you help me? I was scammed and lost an amount of hard-earned money

I see that it needs a 5525 barrel connector but what length 9 or 14mm?

Does rpi zero have a built-in overvoltage / overcurrent protection? Or it relies on the quality of power supply and will potentially fry the board if there are any issues with PD mode selection on the charger side? Asking because I already fried couple of projects by adding type-c ports with pull-down resistors and plugging them into 65W GaN charger

Great vid, thank you! Wanted to see how easy it would be to repair this because mine doesn’t hold a charge very well anymore

what do we do after we get the chat id

Do you know of any way to add two USB inputs on a single Zero 2 W? Ideally USB-C

What is this for

is there no way to fix this without making a mess of the breakout board? or how do i find a breakout board that isnt wired like this?

why do you need to put the resistors on when the micro usb port didnt have any?

Maybe somebody knew if SI7211-B-00-IV will be working too? Cannot find it in my country.

Does doing this make it so that all cable can work with it? Because I'm trying to put this in my phone, I'm going to remove the micro usb and put this in as a better connector

I got one usb board and the resistor was 56kohm. Think designer stuffed up.

how did you manage to get the connector to stay in place when its legs are not embedded in the circuit board? I tried it and the connector just got ripped away when unconnecting the cable. Btw I did a jum between the V+ pins so that the cable works both ways.

A showcase of it working would have been nice.

Thank you very much , nice project! Can you try to build flume extractor with gas mask filter ( from military gas mask ) , problem to have good air flow from iron to filter, may be you will need two fans before and after filter.

Are you able to do PD out of this type C connector? 9v or 12V?

Always check reviews before you buy ANYTHING....

After I get the chat ID identifier what do I do next ?

After I get the chat ID identifier what do I do next ?

THX for your help. Great

where is the link?

I did dat I press start & said hello went to the site & pasted the chat token & it’s sayin cannot get chat ID where did it go wrong ?

Bro how to send it to someone

If you need telegram otp in bulk(usa) low rate(0.15$)and members in (1K/2$) please send me a message in telegram @Kill9