Відео

Hi, do you happen to know which pipe is feed line (the metal pipes) i dismantled mine and forgot to mark them up. Thanks!

Just saved my life with the directions on the fuel level sensor removal. Appreciate you

How are you going to open your under hood fuse box with that it the way? Move it over to the other bolt next to negative on wall

did you require the larger over fenders like they say on the website? I really want to run these on my rolled stock fenders. Thanks,

Thank you. Your video was the most helpful. I’ve watched numerous videos because Cali Raised does not have instructions on how to wire the ditch lights. I realized when I had already cut and attached the wires to the harness that I should have done it after I fed the wires through the firewall. 🤦🏽‍♀️ and I found your video after that. Anyways, thank you again!

love the video!!!

Didn't show the install though. 🤔

Useful info fella. Thank you.

Good, detailed video. About to refresh my leaky SR trans and this is helpful.

So soothing to hear you speak, like the Bob Ross of the automotive world

I’m having the same issue where the gas tank is leaking. And it’s coming out from the seem left side. Is there any possible solution fixing a “crack” on a plastic gas tank? I just don’t wanna spent on fuel cell setup. It is currently my daily.

Hey brother on 13:41 does the red/blue/green connector go anywhere? Can’t seem to find anything about it.

Do you know where I can get the gas tank of this car? (Not ebay) I have this same model of car and I have problems with the tank, I don't know if you will know about any website in China

Question do I need to drop my tranny to install the speed sensor & reverse light sensor? I did the manual swap on my s14 with an s13 tranny

I have a 96 and I have a 95 fuel level sender so basically I can make it work and just not use the extra wire and just wire in the 3 wire ? Instead of 4 wire

What rotor width is needed for the rear z32 calipers?

how is this the only video on the internet about these drop knuckles

@fitted life is the z32 ebrake shoe mandatory for this swap? Or is it just better?

Clutch release sleeve sr rb same height?

Awesome content ma dude, have you ever tried repairing the tank crack issue? Also how did the foam strap hold up?

I love the adds

Sup dude! How's the S14 project coming along? Looking forward to more updates from you.

Did you not bench bleed the master?

My coilover is stuck to the knuckle. How do I get it unstuck

love the content!

I would like to do the same swap right now I'm at work so I'm just hearing what you say but can't wait to see what you do also if I can get a list of everything you ordered I would appreciate it

I have same problem with the oem switch but mine is more worse ! I go to home depot to get a pack of #30 O-ring to make more space for the switch doesn’t go to deep in and put a little bit hot glue to make the switch main board doesnt moving up and down and guest what , its really perfect fit and now its become really OEM mean ! Hope my idea will help you guys 😀

Subbed!!! Learned so much im getting ready to do mine.

რომელ შტატში ცხოვრობთ??

მაგრად მიყვარს ეს მანქანა ღმერთმა მშვიდობაში მოგახმაროს!.,!🙏❤️🇬🇪❤️

man those crush washer goe one on either side of the bitting not together at the end.

Do you have your rear lower control arm threaded all the way in ?

What brand z32 brake master cylinder is that? I need to get a new one

How to remove the metal plate or bracket inside the tank? What does the clips look like that holds it in place? I cant seem to get it dislodged and out. Its rusted bad. Also the fuel pump bracket was just laying inside the tank. Not attached to anything. How and where does it attach to? Thanks

Great video :) - subscribed because of Sympathie 😎 How’s the quality compared to Ikeya Formula, GKTech etc.? Japanese dudes use B-Knuckles from Naomi for example..

Man watching your vids gets me so much motivation.

Awesome video! How is the gas tank holding up? How happy are you with the foam padding? Anything you would have done differently?

May I ask what's the black plastic cover coving the positive terminals next to the fuse box?

With these crazy new car prices, how much did that cost you?

omfg this got me rolling "keep spending money on your project car and hopefully it'll run one day"

That wiring run looks great! I started using a breaker recently on my trunk battery mount and love it, wish I added one years ago.

Oh man, I feel your pain! I stumbled across your channel while researching replacement of my leaky s14 tank. Great video, I love your laid back style and the way you preset your content. So how's your S14 these days?

Nah dude, this was super informative! Thank you for going into detail on how to install this!

Great high quality video !

Awesome content bro keep up the great work! Very informative and on point. Hope to see more s14 content. God bless

Loved the vid

Would the max dual caliper knuckles kit could be Installed with all stock suspension other than coil overs? I pulled the z32 rear drum brakes of a car and I would like to get this kit and install it on my car and get the dual brakes plus the drum brakes. Thanks in advance

hey dude congrats on everything!

Happy to see you back!

so the positive cable from the battery goes to the fuse box ? and that FL 100a from the fuse box goes with that terminal?