Motive Automation
Motive Automation
  • 126
  • 465 198
Basics of Relay- রিলে কিভাবে কাজ করে তার বিস্তারিত | রি‌লে কি ও কিভা‌বে কাজ ক‌রে, কত প্রকার ও কি কি
Basics of Relay- রিলে কিভাবে কাজ করে তার বিস্তারিত
An industrial relay is an electrically operated switch that allows a low-power signal to control a high-power circuit. Here are the basics:
Components of a Relay
Coil: A tightly wound spool of wire that acts as an electromagnet when current is applied.
Contacts: Levers that can be opened or closed by the coil. They can be normally open (NO) or closed (NC).
Terminals: Points where wires are connected to the relay.
How It Works
When current flows through the coil, it generates a magnetic field that pulls the contacts together, allowing current to pass through the circuit. This mechanism enables a low-power signal to control a high-power circuit, providing isolation and safety12.
Types of Relays
Electromechanical Relays (EMR): Use physical moving parts to open or close contacts.
Solid-State Relays (SSR): Use electronic components without moving parts, offering faster switching and longer life2.
Applications
Industrial Control Panels: For monitoring power, controlling motors, and automation.
Automotive Systems: To control high-current devices with a low-current signal.
Home Appliances: In devices like furnaces and elevators for safe and efficient operation12.
রিলে একটি ইলেক্ট্রোম্যাগনেটিক সুইচ যা বৈদ্যুতিক সংকেত ব্যবহার করে কাজ করে। এটি একটি কয়েল এবং একটি সুইচিং অংশ নিয়ে গঠিত। যখন কয়েলে বিদ্যুৎ
সরবরাহ করা হয়, তখন এটি একটি চুম্বকীয় ক্ষেত্র তৈরি করে যা সুইচটিকে অন বা অফ করতে সাহায্য করে
রিলে সাধারণত বিভিন্ন ধরনের হয়, যেমন:
SPST (Single Pole Single Throw)
SPDT (Single Pole Double Throw)
DPDT (Double Pole Double Throw)
রিলে বিভিন্ন কাজে ব্যবহার করা হয়, যেমন:
বৈদ্যুতিক সার্কিটের সুরক্ষা
ট্রাফিক নিয়ন্ত্রণ
মোটর ড্রাইভ নিয়ন্ত্রণ
অটোমোবাইল স্টার্টার সোলেনয়েড
এই ভি‌ডিও‌তে আপনারা জান‌তে পার‌বেন রি‌লে সম্পর্কে । রি‌লে (Relay) সম্পর্কে পু‌রো বিস্তা‌রিত আলোচনা ক‌রে‌ছি এই ভি‌ডিও‌তে । রি‌লে কি ও রি‌লে কত প্রকার রি‌লে কিভা‌বে কাজ ক‌রে, কোথায় কোথায় রি‌লে ব্যবহার ক‌রে, কিভা‌বে কা‌নেকশন দি‌তে হয় সব কিছু নি‌য়ে খুব সহজ এবং সুন্দর ভা‌বে আলোচনা ক‌রে‌ছি । যেন যে কেউ একবার ম‌নো‌যোগ দি‌য়ে দেখ‌লেই পু‌রো বিষয়টা বুঝ‌তে পা‌রে ।
ভি‌ডিও‌টি পু‌রো দেখার অনু‌রোধ রই‌লো । এই ভি‌ডিও সম্পর্কে আপনার ম‌নে কো‌নো প্রশ্ন থাক‌লে অবশ্যই comment ক‌রে জানা‌বেন ।
ধন্যবাদ ।
Electronics এবং Electrical সম্পর্কে ব্যা‌সিক থে‌কে এ্যাডভান্স জান‌তে চাই‌লে Motive Automation চ্যা‌নেলটা subscribe ক‌রে পাশে থাকা বেল আইকন টি All ক‌রে দিন । কারন প্র‌তিটা video তেই এ্যা‌নি‌মেশ‌নের মাধ্য‌মে একটা বিষয় কে খুব সহ‌জে উপস্থাপন করা হয় । তাই Motive Automation চ্যা‌নেলটা অবশ্যই আপনার উপকা‌রে আস‌বে ।
Keyword:
Components of a Relay,Coil,electromagnet,coil,Normally open (NO),normally closed (NC),Terminals,Points,How It Works,current flows,contacts,SSR,8pin relay,14 pin relay,relay logic,রিলে কি,রিলে কেন ব্যবহার করা হয়,রিলে কিভাবে ব্যবহার করা হয়,৮ পিন রিলের ব্যবহার,মিটার দিয়ে রিলে কিভাবে চেক করে,১৪ পিন রিলে,রিলের প্রকারভেদ,রিলে কয় প্রকার,ইন্ড্রাস্ট্রিয়াল রিলে কিভাবে কাজ করে,how to work relay,motive automation,8 pin relay logic,14 pin relay logic,রি‌লে কি ও কিভা‌বে কাজ ক‌রে, কত প্রকার ও কি কি,
#রিলে_কি
#রিলে_কিভাবে_কাজ_করে
#রিলে_কত_প্রকার
Thank You
-Motive Automation
Переглядів: 52

Відео

DVP PLC Read High Speed pulse input Compare Encoder Pulse ABZ and Pulse Frequency
Переглядів 4556 місяців тому
DVP PLC Read High Speed pulse input Encoder Pulse A-B-Z, and Pulse Frequency 1) #highspeed -Speed #pulse count A-B-Z 2) #Calculate #PPR and Count 3) #Read Pulse #Frequency/ RPM C235 = X0, U = M1235 OFF When D = M1235= SET X0= A -phase C235 = R/F = M1270 Up/Down Counter Mod = M1235 M1235 ON = C235 mod is Down Count M1270 ON = Negative PLS M1235 OFF = Up Counter M1270 OFF = Positive PLS X1 = C236...
How to Program FX5U PLC Digital IO Analog IO Pulse Output, and GX works3
Переглядів 3716 місяців тому
Getting Started with FX5U PLC and GX works3 1) Configure Build in analog IO 2) Configure Global Variable for Digital IO 3) Configure High-Speed pulse output in this tutorial, we control a VFD Frequency control using (0-10vdc Singnal) And Servo Control using pulse Positing signal let's gear up first, we make a global variable Digital Input X0 = Emergency Stop X1 = INV FWD Start X2 = INV REV Star...
SIEMENS S7 1200 CB 1241 Modbus RTU Communication With RS485 Sensor and Multifunction Meter
Переглядів 3,1 тис.6 місяців тому
MB_COMM_LOAD Communication frame: a) Port Selection (RS485) c) Baud Rate: 9.6 Kbps d) Parity bit: None c) Stop bit:1 d) Communication MB_DB for MB_Master MB_MASTER a) MB_ADDR: SLAVE ID NO b) MODE: SIEMENS MODBUS MODE 0: Read Data 1: Write Data DATA_ADDR: Slave Register Data Address DATA_LEN: for INT: 1, DOUBLE: 2 DATA_PTR: Define variable/ Data block for Mov modebus readable dataMeter Modbus Co...
Delta DVP PLC Temperature PID- GPWM and ISP Soft Part 2
Переглядів 1,1 тис.6 місяців тому
00:00 intro 0:15 start 6:8 program simulation 11:23 PID mode set PID = proportional integral derivative GPWM = General Pulse Width Modulation PWM = Pulse Width Modulation PV (process value/process variable), SV/SP (set value) and MV (manipulated output value) can be transferred to other measuring instruments. A cost corresponding to one temperature sensor can be reduced just by connecting a PV ...
Delta DVP PLC Temperature PID- GPWM and ISPSoft - Part 1
Переглядів 9166 місяців тому
00:00 intro 00:20 class start PID 05:15 PID program start 07:37 PID parameter setup PID = GPWM = General Pulse Width Modulation PWM = Pulse Width Modulation PV (process value/process variable), SV/SP (set value) and MV (manipulated output value) can be transferred to other measuring instruments. A cost corresponding to one temperature sensor can be reduced just by connecting a PV transfer signa...
DVP PLC Read Pressure from 0 -10vdc analog input , pressure convert psi to bar and ISPSoft
Переглядів 3176 місяців тому
DELTA DVP PLC Analog Read 0-10vdc and Display Pressure 0-10bar from 0-10vdc ISPSoft 1 bar = 14.5038 Pound per sqr, inch PSI 0-10vdc Pressure Sensor Analog input Calibration All are Proportional Data Step1) 0-10vdc, 0-10 bar, 10x 14.5 = 145 PSI Step2) 0-10 = 0-10vdc 0bar = 0 v 10 bar/ 145PSI = 10vdc Step3) 10vdc = Digital RAW data = 2000 Max Raw Data Step4) Pressure Per/ Digital RAW Val = 10/200...
How to Read 4-20mA from PT100 Sensor to Current Converter with a DVP PLC on ISPSoft, DOPSoft-4
Переглядів 4,7 тис.8 місяців тому
DELTA DVP PLC Analog Read 4-20mA and Display Pt00 Sensor Temperature from 4-20 mA ISPSoft 4-20mA Analog input Calibration All are Proportional Data Step1= 4-20, 0-100c Step2= 0-100 = 4-20mA 0C = 4mA 100 = 20mA Step3= Current Span 20-4 = 16mA Step4= 20mA = Digital RAW data = 1000max Step5= 20 ma = 1000max 1 ma = 1000/20 4 ma = 1000x4/20 = 200 1000-200 = 800 200 = 0C = 4mA 1000 = 100C = 20mA Step...
How to Configuration DELTA DVP SE PLC IP Subnet Mask Ethernet Network on ISPSoft
Переглядів 2828 місяців тому
1) 12SE PLC Feathers 2) LAN IP Setup and DCI Soft 3) Network ID, HOST ID, Gateway 4) Prog. with ISP Soft IPV4 = 32bit 192.168.0.2 = PLC 192.168.0.3 = PC 255.255.255.0 = Subnet Mask 192.168.0.1 = Gateway
How to Configure Control Register of Temperature Module of DELTA DVP PLC on ISPSoft
Переглядів 5248 місяців тому
DELTA DVP PLC TC_RTD Analog Input Module Configuration and ISPSoft Delta DVP TC/RTD Temperature Module Configuration Delta DVP Analog input Module Configuration and Read 4-20 mA/ via RTD to 4-20mA Converter Digital Range for Max 700 Dg = 7000 700x10 = 7000, So Multiply factor .1, Temperature Resolution or unit, input digital val x .1 = Actual Temperature 12-bit resolution on their analog inputs...
S7 1200 PLC and Furnace Temperature PID Controller
Переглядів 588 місяців тому
For the targeted influencing of certain quantities in a technical system, these quantities must be controlled. Controllers are also used in a wide variety of applications in automation technology, for instance speed control. For the SIMATIC S7-1200/S7-1500, the technology object "PID_Compact" is provided for proportional actuators. Description of the automation task The automation task consists...
How to Configure Analog Input-Output of Delta DVP PLC on ISPSoft
Переглядів 9718 місяців тому
analog input signals (voltage or current) and convert them into 12-bit digital signals. DVP06XA-S receives 2 groups of 12-bit digital data from the PLC MPU and converts them into 2 points of analog signals for output (in voltage/current). The user can select voltage or current input by wiring. Range of voltage input: -10VDC (resolution: 5mV). Range of current input: -20mA (resolution: 20uA). Th...
S7 1500 PLC PID Compact and Heating Cooling Configuration TIA V17
Переглядів 3148 місяців тому
1) SIEMENS Analog I/O Calibration= int VAL 0- 27648 Note that the value 27648 is only the "Rated maximum analog value (0- 27648)". The other range in the PLC is the "overcontrol range (27649-32511)". While the real maximum value is the "overflow (0-32767)". 2) The value 27648 has simply been selected as the maximum normal range value of any analog signal transferred to the CPU by a Siemens anal...
SIEMENS S7 1500 PLC Analog IO Configuration TIA Portal V17
Переглядів 2988 місяців тому
1) PLC Analog I/O Allocation And Trainer boar Wiring Config 2) Pulse Generator And S7 1500 CPU Clock Memory Setup S7 1500 Web Server 3)Function block , S7 1500 Web Server and Watch Table Configuration 4) PLC Data types, TAG Table and DB block programming Global and Local Variable Fair Use Disclaimer: For Bangladeshi Contents: This channel may use some copyrighted materials without specific auth...
How to use Instruction- TMR, ADD, SUB, LD, LDI on Delta ISPSoft, Tutorial-3_1
Переглядів 37210 місяців тому
Todays Topics a) PLC Wiring Digital input and Output b) DVP ES2/EX2 Memory Map c) Device list of ISP Soft (X,Y,M,T,D) d) ISP Soft programming Instruction TMR, ADD, SUB, LD, LDI This is series tutorial for industrial automation and Delta PLC Programming Beginner to Advanced in ISPSoft. ISPSoft is the latest program development tool for Delta's programmable logic controllers (PLC) that complies w...
How to Download And Install Rockwell Automation Micro 800 Allen-Bradley free PLC Software
Переглядів 1,5 тис.11 місяців тому
How to Download And Install Rockwell Automation Micro 800 Allen-Bradley free PLC Software
Industrial Automation and ISP Soft Tutorial 1_1
Переглядів 22311 місяців тому
Industrial Automation and ISP Soft Tutorial 1_1
Industrial Automation and ISP Soft Tutorial 1_2
Переглядів 16111 місяців тому
Industrial Automation and ISP Soft Tutorial 1_2
Industrial Automation and Delta ISP Soft Tutorial 0
Переглядів 32511 місяців тому
Industrial Automation and Delta ISP Soft Tutorial 0
How to install and Design in AutoCAD Electrical 2023
Переглядів 8 тис.11 місяців тому
How to install and Design in AutoCAD Electrical 2023
How simulate Modbus master-slave Communication on PC.
Переглядів 14 тис.11 місяців тому
How simulate Modbus master-slave Communication on PC.
How to Install and program in TIA Portal V16 And WinCC Unified
Переглядів 8 тис.11 місяців тому
How to Install and program in TIA Portal V16 And WinCC Unified
Real-Time Data Visualization On Customize SCADA
Переглядів 85Рік тому
Real-Time Data Visualization On Customize SCADA
How To Install and program in TIA Portal V 15_1
Переглядів 8 тис.Рік тому
How To Install and program in TIA Portal V 15_1
Service offered by motive automation
Переглядів 90Рік тому
Service offered by motive automation
How To Install and program in WinCC flexible SMART V3 SP2
Переглядів 7 тис.Рік тому
How To Install and program in WinCC flexible SMART V3 SP2
How To Install , program in and Logosoft V7 to Upgrade V8 3
Переглядів 3 тис.Рік тому
How To Install , program in and Logosoft V7 to Upgrade V8 3
Programming Support To Remote Client project demo
Переглядів 172Рік тому
Programming Support To Remote Client project demo
SCADA application Modbus Demo with Visual C#
Переглядів 505Рік тому
SCADA application Modbus Demo with Visual C#
PC SCADA application Project Demo with Visual C#
Переглядів 401Рік тому
PC SCADA application Project Demo with Visual C#