Відео

I dunno about those side bars where they are. Are the bars supposed to stop something coming up under the van? or are they to stop things from hitting the van side-on? They just seem to be removing leg room, without helping with the side knocks.

What about fitting chrome roof bar

Hello mate, any chance you can let me know where you get them resistors from? Thank you.

Just done this today worked a treat, I’ve taped over the resistor around the plug,the resistor won’t get hot will it? Thanks

Very useful. Thanks very much.

Can you wire side lights in parallel and straight to the the rear side lights?

Smart looking van. Very nice

Liked and subscribed ❤

Thanks for showing this, just bought side bars for my Primastar , this tutorial is going to be a great help. Very much appreciated. Keep up the good work

Hi, i want black rather than chrome bars. Can you recommend what i should use?

Hi i have tried this but no luck however my passenger seat is a double which i have added a swivel to. Can i use more or do i need stronger resistor?

Nice work

Of the white wires by the fuse box, how did you work out which wire was the reverse wire? I have several white wires. A really fat one and a few other smaller ones. Many thanks.

Looks great

So please explain : are the the two BLUE wires ON the CAM buss ? And the SEAT BELT sensor is just wired across ( in series ? ) on the CAM BUSS The CPU is looking for 3.3 k ohms ? To know that either the seat is being sat on or not .? And your just simulating the sensor being sat on ,, is that correct ?

Amazing tutorial mate, this have helped me out big time! Keep up the good work 💪

Exactly how im doing mine...saves taking out those unwin tracks out of my ambo...great job😊

Nice one 👍

Hi thanks for the video really has helped Is it the same resistor for both seat tensioners/ wiring As was told it’s a different ohm for twin seats Any advice would be most helpful thanks 😊

Hi can I talk to you if you are taking on vans to fit one of these camera I’ve already brought one but want someone to fit

Great ! And the most important bit , how to wire it into the switch, You decided to Run It at 300 mph

Pity you didn't actually show how you fitted the bolts down though the roof. Washers, sealing ect

Thanks

Use a skateboard wheel with the bearings still in it, just put a pencil through 👌

Cabt find any later vids on this

A small sharp floor scraper would of removed that old sealant faster.

2:12 Top tip 1: I didn't need to take off the top light cluster I was able to feed some TV coax cable, which is stiff allowing yo to push it, through that rubber ducting into the van. Top tip 2: I sprayed the cable with some cooking oil and it slid in nicely and never played hard to get. :)

Hi big fella could I of bollted the 5mm bar to the bace instead of wellding it? I'v been watching a lot of your vids are thy are brill no messing about .

Too long foing a job wr dont have yo see from stat to finish

Taking to long on jobs

Smashing bloke, just brought one of these and the instructions are useless and mine are in B&W you’ve got my sub

Ok but why turns on only when you put the gear on reverse? Wouldn't it be better to be always on?

How do I contact you?

Presumably, if you're just putting the original seat back in, you don't need the resister trick. Been looking for how to remove the seats out so I can clean my Van properly (just bought an ex trade van, so its got years of dirt in it) and maybe even recondition the seats themselves. This vid is the best explanation I've found!

Good video but don’t need that horrible music

ua-cam.com/video/KjaDbi1w2Ko/v-deo.html I honestly hought you were joking about the nails. :O Are you serious? Surely you run the risk of nailing into cabling, brake or fuel pipes that are unseen underneath, any mild steel panel pin nail will be rusted out within a few years. ua-cam.com/video/KM2K7sV-K74/v-deo.html Those underlay board surely need only a small dab of glue here and there to stop them from moving over time. I would envisage that too tidy a job on underlay may be a problem to allow for contraction and expansion of the floor?

Those alloys look suspect under any VOSA inspection :O ua-cam.com/video/LmftofVjFcQ/v-deo.html

I think i'm clocking out of work and going home and doing this bro😂

Brilliant bro.. I've been looking for something like this to make a platform for my s. U. V so I can sleep on it. You just saved the day if I was there I'd buy you a beer right now

Almost certainly motherboard so would need both bought together so they match (around the £30 mark). If the sequence isn't right it simply won't fire up and all of that is handled by the main board. I've yet to investigate but I suspect its down to the relay or associated components on that board that switches the glow plug on. E-8 is simply no burn. Its not always fuel (although the first place to start) - it simply means the unit hasn't fired up. I'm fairly sure the relay on the motherboard handles the ten or so amps for the glow plug and I suspect that if the secondary side fails, as far as the motherboard and display know, the glow plug is actually powered up, but in reality no power is going to it, even though one side of the relay has energised and the display says all is well. The only way to know for sure is to put some test probes in the glow plug socket on the motherboard with everything connected and see if there is power there (and how much) when display shows glow plug is on. Easy enough to verify if glow plug actually works by hooking it up to a 6v battery (briefly) with a couple of test wires shoved in its socket.

Is it 12v tv?

Way to go, add 100 to 200 Kg of needless weight to you van permanently. Then sell it a couple of years later due to prohibitive MPG costs...

How do you clean the sewer pipes of the shower as the get pretty nasty in couple weeks?

Hi, do you fancy a weekend away in Rye East Sussex on me?. I have this same make model of bus and would love your advice and help. Chris

Thanks ....my bullbars / sidebars going on next week 👍 subscribed

Did you disconnect the battery for all of this installing the wiring etc

we are doing a campervan conversion on a 21 plate Citroen Relay, the seats are out and gone onto better things, and are replaced with Galaxy captains swivel seats. would the resister required be a 3,3ohm one as well, or is each van going to be different, and where would I locate that info? Thanks for your time

Absolutely brilliant, great editing and information. I’m building my camper currently over on my channel and taking great inspiration from this. New subscriber right here 🙏🏼 thank you 👍🏻 JP Living the dream

Hi Wayne,you are so rite about insulation, I was lucky a company I used to collect from and too, specialises in insulation for buildings and tower blocks, so I managed to blag the insulation and reflectives for free too, a little factory in South Wales called Siderise.

This has really helped me out, I thought I’d have to take it to a garage to get it sorted at great expense. £5.99 later and it’s all sorted, cheers! Top man