Відео

I've got a mk2 C-Max with the 1.6L Duratec Ti-VCT engine, which looks exactly the same, same inlet manifold and PCV valve/hose location etc. However, I cannot whatsoever get my hand through that gap. I have quite large hands, but not massive; I'm only 5'8". Is the gap bigger on this engine? Any tips on gaining access without removing major parts? Cheers, great video though

Thanks!

Hi Sir, Very clear instructions demonstrated by you. Thank you for that.

What fuse or relay is for the wipers and windows. Thanks!

What good is it if it can only be done when the engine is off? 🤣

Thanks, have an issue with the marker lights working randomly

buymeacoffee.com/cliveuky

I've got the 2011 Corsa 1.0 and I've currently got a P0107 fault code for the MAP sensor which when I've replaced makes the engine run terribly/not at all. I've been told that the EGR valve could be causing the actual problem. Have you got any experience/advice/thoughts on my scenario? Great video regardless

I've tried 2 new motors and a 2nd hand one now, get no power to them however if I plug my original one in you can here the motor. Think there's an issue with my connector

this video was very helpful, i would like to donate £10,000 for this brilliant video

Hey Mate, Thanks a lot for this fantastic video - That is how they need to be.

Hello van you tell md the problem you had. My fan stays in all the time Evan with mo keys. In the van only way is to pull fuse out .to stop it .thanks

Thanks for the heads up on how to do this . Much appreciated.

Very helpful, thank you

Does the drain plug stay in? I have turned anti clockwise but the flow is very slow and the drain plug just keeps spinning?

This is. Ot a valet key because it can't start the car

Big Thx !!!!

I can't thank you enough, I have subscribed liked the video....my van wouldn't start unless jump started by pushing ...watched your video and walla the egr was stuck a bit of ew40 and I'm back at work...will take a day off now just to clean the whole manifold...Thank you a million times

That would be a really awkward sod to replace 😕

My front washer is ok.the rear one isn't???

Thanks for posting. was very helpful.

This doesn’t work for basic multimeters it would seem

Thanks mate!

Why did you replaced? What it was the symptoms?

8

Update! All good, I was looking in the wrong side. On left hand drive cars it is in the passenger side or the right side. Many thanks. Blower working on all speeds now.

On my daughter’s 2015 Fiesta, the resistor is not in that location. I cannot find it? Bought a new one but nowhere to fit it.

Thumbs up, you saved my a$$

Super video 😊 It fixed my car, thanks🙏🏻

Hi does it stay or not ?

Just checked mine. It's clean 🤷

MERCY 👍👍👍👍👍👍👍🙏🙏🙏🙏

what a video !

My fan kept kicking in going limp losing power but noticed getting real hot didnt know even had one but thermostat gone engine oil reading -40 (once plugged in ) but wish i see this before i took down garage (dont think it will make it bk home ) ive fiesta edge 2011

Is there a fuse for the door sensors mine won’t stop going off even when all the doors are shut

Thank you for this! A minor nit pick, as a general rule, the final quarter-turn tightening is best done once all other bolts are already hand tight.

Mine goes into limp mode without warning even when sat on cruise. Have to flick it off/on an itll reset. Not cleaned or even looked at um but will report back when i do. Thanks

THERE ARE NO VIDEOS ON HOW TO REMOVE THE BUMPER!!!!! 😠

Cheers bro for 2 reasons 1st i suspect i may have a dogdy coil pk and 2 i was just looking into buying that probe happy days ✌️😀

Well described 👍🏻

Great informative video! I have the vauxhall combo 1.3 cdti and I have the car with spanner through it, comes on every now and then, any thoughts on what is making it come on? The van drives great

Would of been helpful if you could of mentioned if the 02 sensor does need changing is that the only one

Absolute legend! What a video, not everyday I search for a how to video and get an actual guide as easy to follow as this! Just an observation, did you do this without jacking up the car mate? Cheers!

What other reasons would this stop working. Changed my oil pressure sensor and went off altogether fuses fine.

Te estoy muy agradecido, me has ayudado muchísimo. Un abrazo desde España

Is that the only filter

Many thanks for posting this info ! Much appreciated.

Can't get the damn wires to come out lol. Any tips?

THX!!!

That means your whole EGR system is filled with that crap. You need to clean out the entire EGR system if you want to do the job properly.