- 7
- 41 671
Brand Built
Приєднався 20 чер 2015
2012 Ford Fiesta Revival Pt.1 timing belt replacement
I am bringing this little Fiesta back from a life of sitting and disrepair. in this video ill be starting with the timing belt (2011-2020 Ford Fiesta 1.6l).
Country Cue 1 by Audionautix is licensed under a Creative Commons Attribution 4.0 license. creativecommons.org/licenses/by/4.0/
Artist: audionautix.com/
Dobro Mash by Audionautix is licensed under a Creative Commons Attribution 4.0 license. creativecommons.org/licenses/by/4.0/
Artist: audionautix.com/
Country Cue 1 by Audionautix is licensed under a Creative Commons Attribution 4.0 license. creativecommons.org/licenses/by/4.0/
Artist: audionautix.com/
Dobro Mash by Audionautix is licensed under a Creative Commons Attribution 4.0 license. creativecommons.org/licenses/by/4.0/
Artist: audionautix.com/
Переглядів: 11 877
Відео
3100 SQ FT House slab pour (mostly time lapse)
Переглядів 362 роки тому
Cheap Amazon Catalytic Convertor Install on 2005 Toyota Sienna
Переглядів 16 тис.3 роки тому
This afternoon I am installing a cheap Amazon cat on our 05 Sienna. I show the process with a few tips along the way
Ball joint eliminator install on Jeep Wrangler (JK/JKU)!
Переглядів 6353 роки тому
Installing a Ball Joint Eliminator Kit from American Iron Offroad on this 2017 Jeep JKU. Hopefully I've covered everything. i apologize for the heavy breathing asi have seasonal allergies that got me wheezy. Also for the lack of camera angles for i only have one camera and no editing skills LOL.
Playtime! Bandit 18xp tracked wood chipper
Переглядів 13 тис.4 роки тому
We have a big ole bandit tracked chipper on site this week and I got my hands on the remote!
Bobcat T770 with forestry package for sale
Переглядів 1244 роки тому
Our company has decided to let the ole T770 go and replace it with newer equipment.
Exactamente nesecito cambiar mi catalizador de mi Toyota Sienna 2008 pero no se si tiene dos o solo uno ??
You got a po430 which is bank 2 I assume. I have a 2004 Toyota sienna le with a po420 which is bank 1.gonna do the same
fantastic video, I like your patience with the process
I followed your video to a tee except my flywheel locking tool broke when I was trying to get the crankshaft bolt off. Any suggestions?
Were you able to get the broken piece out?
@@justinbrand6585 I am not sure where the piece went. I bought another tool and got the timing belt replaced and all works great. Hopefully the broken piece isn’t inside the flywheel case. Oh well.
@@grneal26 hopefully no further problems arise
was a good choice? which brand you buy can you send me the link
Thanks for the video good job 👍👏
"De-gas bottle", I heard that as bigass bottle 😁
about to tackle this on my sister's car, have one question...the crank sprocket has no keyway? the only thing holding it in the correct position is the torque of the crank bolt? Ive done several Japanese cars but Ive never heard of anything like that
There are TREEE bolts for the starter! DO NOT make a mistake like I did.
ua-cam.com/video/KANMQFhv3v0/v-deo.html
great instructional video!...tip: serpentine stretch belt can be installed with a tie strap, no need for plastic tool.
Is it just me? Does this seem pretty complicated?
It’s really not that bad just a little more fidgety than say a 90’s Japanese car
My 2012 just hit 175k. Runs like a top. Luckily is a manual as well. But time to do this as a preventative. Probably do clutch and head gasket too. Love that car. Best car I ever owned. 7 years just brakes and oil changes.
If the head gasket and clutch aren’t faulty then don’t do it
And lower arms and tie rods too 😂😂😂😂
Did you have to lower the engine? My crank pulley bolt is right up with the metal frame and not accessible straight on like in your video. I don’t want to drop the engine too far and risk potential damage.
I did a water pump job for this same car but weeks later the car will not start up anymore I believe because I did not use the Cam tool kit that something may have moved and now jumped timing. Is it possible for me to get this cam tool kit And only use the Small pin on the back of the block and rotate it back to timing?
Is there any way we can leave the timing chain cover off.😅😂
Great video...how much did it cost you the catalytic converter?
Hellooo
Thanks for taking the time to video this. Saved me a bunch of time. I appreciate ya!
Can you please give a link to the tool you used to keep the gears in place?
That's a big job! I just bought a 2015 SE. 166,000 Km on it. I better do this one
Do you really need the flywheel blocking tool. Or can you get away with just the crankshaft blocking pin?
I was wondering the same thing. Hope he answers.
@@trentstewart5144 I have done this job last weekend. You don't need the flywheel tool, but I had a big impact gun. If you don't have a big impact gun you will definitely need the flywheel tool. Just keep checking TDC and if the cams are alligned.
@@joeyvisser6953 thanks man.
That puller in the kit not work for the crank pulley? I was looking at the same kit for this job. Thanks.
I had 3 screw for removing the metal piece behind the alternator
Just successfully changed water pump and timing belt and serpentine belt all thanks to your video! I can't thank you enough! You rock!
Happened to come across this video after just having the whole exhaust installed off of parts found on Amazon. I have that specific catalytic converter but other parts area mix since not everything was readily available. Everything came to around $1k which is inexpensive for a whole exhaust, clamps, hangers, and sensors. Probably saved about $3,000 at least. I didn’t want to put anything too expensive in it because it’s almost 20 years old. The car is now running like a champ so far. How is yours holding up a year later?
I actually sold the one in the video but we have another one that we had longer than that one with the same cat and it is doing fine.
@@justinbrand6585 great to hear. I don't expect any miracles but the cost of parts these days are ridiculous, esepcially if it's from a supplier to a mechanic. The exhaust wasn't any easy job because I don't have a lift and it's New England (also no garage.) Luckilyy I have a mechanic that agreed to putting it in otherwise the car would've been sold for scrap. I just made sure I had everything including new oxygen sensors and all of it was Direct to Fit. I don't think the exhaust on these are not something you can tackle with ramps or jack stands.
no se ingles ,pero el trabajo que le vi hacer me encanto , un millon de gracias y salud a la familia
gracias por ver amigo
Can u explain why u chip all that wood
We were clearing a hillside for a homesite.
Most of it was deadwood and the chips help with erosion control
That looks insanely fun!
Getting to play with new equipment is always fun!
My 2007 shows code p0430 catalyst system efficiency below threshold bank 2
Hi do you fix it i have the same code
I was told that there are actually four cats on the van, is this true? I have read that there are only two. I get different answers from all over the place! I have codes for bank one and two and i cant seem to get them to clean enough to get it smogged!
There are three, two manifold cats and a post cat
@@justinbrand6585 thank you! Im getting 430 and 420 on both banks one and two. Would i get a code for the third bank too, or is that one still good and i only have to change bank one and two? And do you know where i can get the cheapest california legal cats that are an exact fit? I have searched the internet for HOURSSSS and all of them are super expensive!! HELP!
Nice video. How has the new cat held up so far?
I have two of them one I did all the supporting stuff too is fine the other I just slapped a cat on and it keeps throwing cat codes. I'm going to do the tune up and pcv and see if that fixes it.
@@justinbrand6585 Sometime it is super sensitive on if it is not the OEM Cats. People still get codes even after swapping it with an aftermarket cat.
@@CJ-fh5xq yes I know that, I appreciate the info though
@@justinbrand6585 what other “supporting stuff” are you talking about? Replacing PCV Valve? O2 sensors? This video is very helpful and the only one about this cat on my van. Thanks Justin!
Makin it rainnn!!! Wow top of the line!!
How about the cat in the back? Are you planning to change that also? My Sienna has a P0420 code which is the rear cat. I don't know how to change that.
I didn't, my front cat hadn't come apart yet if yours needs to be replaced they sell that one also but it might not be available on ebay. Try checking rock auto or another online parts house for it.
Thanks for the video. Do you have a Amazon part number? Also as an update how does it run with the new cat or did it clear any check engine light?
So far the check engine light is still off and it runs just fine. The one I ordered was the AUTOSAVER88 "brand" on Amazon
@@justinbrand6585 I'm going to buy one of those myself. Better than buying an OEM converter and spending hundreds.
Is that cheaper Amazon car still running good currently?
Thanks for this one 😁
No problem!
Possible to get full time work with one of those ?
The only companies I have seen own them are loggers and guys that have large clearing companies. We had rented this one from a company up north for a large clearing job we were doing.
Who rents that unit?
@@fredsousa4020 too me I think cutting that straight logs up would b better
Great video, it must have smelled great out there with all those wood chips flying!
What a beast. Horsepower?
I think it was a 180hp Cat on that one it was pretty awesome though!