Відео

How do you deal with first initiation of the tool, the peak power consumption is huge so the power adapter goes to "short protection"

Very nice video! I thought about to do the same with a nude wireless charging module into a device. Before starting, i injected 5v into the wireless charging receiver module (like if you plugged the usb cable on your phone) and measured 0.2-0.3 A. This mean the wireless charging module will consume energy and heat a bit. Did you added anything to avoid energy falling back into the wireless charging reciever module?

Thanks for the information great help

Thanx for the info I appreciate it

Hello. How can i Convert my Tolsen Brand Cordless Circular saw into Corded? My Cordless Circular saw is for 20 volts...Please help if it is safe to turn into Corded?

why not use female and male adapters and glue them in place, so you dont have to cut wires of the charger and you also dont have to have it corded all the time?

This looks like an invention only made into reality by weed xD

Thank bro😊

Why fuck up the cordless part why not just take an older battery pack and mod it ? That way you can have cord when you need it ? craftsmen haa a pressure washer I want to do this too.

Thanks was looking to do this. So you have to solder this to the motherboard or can you solder this to the charging port internally. I'm not sure where to install the reciever. Trying to install this in a old phone, the tmobile sidekick phones

Little bit difficult

Just tape and pull it out 😅

This is incredible!!! Thank you for your knowledge! I need to learn how to do this for my cordless vacuum!!

Why not just keep centre cap attached if good condition protecting coil. As long as no glue enters coil why not just leave alone. I have to carry this out but I forgot the foam. I will see what is used. Possibly try foam filler adhesive applied with secondary, small syringe

i have a boscg vacuum that i would like to make corded Model #GAS18V-3N. what kind of adapter do i need?

فيديوا مفيد جداً جداً واكثر من رائع احسنت الاختراع

I don't leave mine in the hot sun. Never had an issue with that.

Amaizing macha 🎉🎉

Hi brother i have charger og 21 volt and 0.8 amp and battery is 18 volt li-ion 1.3Ah And readings on cordless drill machine are 12volt 18-25 NM. I want to to convert it to corded drill machine plz suggest me a adopter or supply please.

thanks, a lot.

Cob only blue❤

Hi sir, can i use the battery charger of my cordless drill as an adopter?

I've got this smartwatch that chargers via pins and I'm considering swapping for wireless, this definitely helps cement my idea as plausible if not possible. Thanks for the vid!

Is this tool brushless

What if I want to make a corded tool run on batteries 🔋 🤔

Thanks... had th3 same issue about to solder my cable to a rechargeable lamp.

Sir please this is kelvin from Nigeria. I deal in tech-electronics. Please I will want you to put me through some things about this changing port. That is if I want to use the usb cable to run the charging port but animation video. And also the alternative way to run the usb cable if the charging port is damage

How did this worked out? and how fast did this wireless charging receiver charge the cell phone? I bought something like as for my cell phone, but I did not do any modifications like you just did' but it took a long time to charge it to the point it's starting heating up the receiver a lot and especially where the battery is as well that can propose a hazard and I'm also kind of concerned about that as well.

Strange! I have a supercapacitor in this recorder.

Just replaced mine. Got my battery on ebay with connections already on it. Thanks for the tutorial!

Hi, do you know the model of original camera for him?

uuuh dude... just use your dead battery... open the battery, remove the dead cells and connect the wires of your adapter to the poles of battery... so you can use one adapter to all of your tools 😜

The power of your adapter is only like 70 watts ,thats not enough to work properly. The tool you used requires like 600 or something..

You are most hairy guru

Well you said don't cover the image positioning sensor but done exactly what you told😥

can i used mighty bond instead of glue?

🤣🤣🤣🤣

Usefull! LIKE!

Wow! I want to see a footage of the Firefly micro action camera while the drone is flying

I don’t think cutting the back of it for better access to the coil as necessary. But I do think it will definitely help with the heat problem.

Yep, this is what I was looking for...for the tech in phones these days I am surprised they aren't standard in all phones.

All the screws should mandatorily have been placed with the COB and heat sink.

Hi how can i convert my 18v OZITO cordless drill to corded? thanks

Thanks for your help and easy visual instructions. My Jackery charger battery and board come out the other end so I needed to have a longer USB wire. It's been sitting unused for almost a year but now it's working. Thanks again!

The thin connector to the screen got damaged. Hardest time trying to push it in. I need a new one and not sure where to find it. Everything else went fine and camera turns on but not buttons for control now. By the way, thank you for the video.

I want to convert my circular saw to corded.. Can you help me man?

I just replaced myn today but iv drilled side of the camera with 3mm hole and pulled the battery wires out and attached them to old nokia 3.7 800ml battery 🔋 and its working just fine

lol lousiest build ive seen yet. fan too small. stingy use of thermal paste. and the zip ties jesus christ

Very nice

Please I tried this but it's charging very slow, it takes more than 9 hours before charging full, what's the problem sir?