Відео

Milwaukee tough baby🙇🙇🙇🦸🦸🦸

You small he big

It’s easier to get a tool from harbor Freight than get the snap on guy to come 30miles when he gets time 😂😂😂

EATING TO MUCH...

You need to get a higher stance and look at his foot wedge you need the same🤦‍♀️

I did it with the 1/4 in 3 dollar ratchet I have no proof f u

Torq order on the bolts 😮

Snap on guy here, my harbor shit breaker has seen some shiiiiiiiiiiiiiiiiiiiiit………still kickin ass and taking names 10 years later

He’s got that meth strength

Too fast. Movement shall not be made in less than one second.

His body is about 220 lbs so he ain’t putting much muscle into it

The cigarette in the mouth just added the extra gram to his body weight that he needed to pull this off😂 Jokes aside that dude is a stud!

220 isn’t even halfway haha. Most of the heads I do have three stages of 90 degrees after that. That’s the struggle. 220 is not the difficult part.

What is he doing right 😂

You lucky he aint bent that nice clicker torque wrench over your head and stuffed you in a dumpster.😂

On guy is flat footed on the open floor the other is bracing his foot and pulling ....simple

Not letting tourqe wrench click back

Lol, tool trucks did give you anything, lol

Idk there’s not much I haven’t been able to get unbolted with my meter long 3/4 drive breaker bar by icon 😂 to include seized on lugs off a nasty ass corroded forklift.

I could never understand how people work with a lit cigarette in their mouths. I tried to do it when I first started working because everyone was doing it and it looked cool. I ended up needing air and inhaled a huge drag instead…I was done for about 5 minutes throwing up and being lightheaded. Never again, that event turned me off of cigarettes.

It’s called LEVERAGE. This is a lube tech level question

Funny you say that... I work at the Milwaukee snapon plant and our 1" drive torque wrench stopped working while repairing a former and the only place to have a torque wrench that size on such short notice was harbor freight. So we now have an icon torque wrench at our snapon tool factory 😅

Wearing a cutoff shirt!!!

You and him have different power to weight ratios

Looks like they have 200lbs on you 🤣🤣

Hes fat and taller duh alls he had to do was lean

Because he had foot placement!

No smoke, you need cigarette power

That cigarette started the same size every clip 😂

You mean to say 300 FOOT POUNDS.

Forgot your crank my good sir

He as big as the cig he smokes shiiiid

Engine Mechanics think thats big, Industrial Mechanics know thats just a little fastener

Un Bothered @ its finest w the cigarette bro...😭🚬🤘

I don't even think Harbor Freight sells one inch drive sockets and they definitely don't have one inch drive ratchets. And seriously man you put a pipe on it. So the snaplan's not pulling it without help

He uses his foot

Hahaha I commonly torque 650 - 850 ft lbs for pressure heads. 300 should be easy with that much snipe

That’s easy with that kind of leverage 😂

All bro has to do is hold on and lean back

No matter what size you are with the right technique anyone can do that

Bros 22

Somebody get this man a sandwich.

With a 6 foot lever? Most definitely.😂

300 ft lbs isn't that hard to do, I work on a farm and we torque our lugs on the tractor at 450

Just bought a Ford ranger. The previous owner must have taken it to this guy one last time to torque the oil drain bolt like this.

And they got the slaps😂😂

Babyface ray??

Easily

why use effort when you can slip a pipe over your bar

Wavy navy