Відео

Always connect positive before negative. Goodnight

Thank you so much ❤❤❤ I just installed in my 2017 tundra appreciate you 🤙

You never checked the relay switch if that is working. By connecting wire to the diagram can fry the whole system so no one should ever do that.

But , my own has issue of wire, relay is okay, fuse is okay, but the wire that gives netive as art to the relay is not working,

What does it mean. When we hear this sound? It means , is it working good?🤔🤔

Thank you! I had no idea about the plastic cover.

I was quoted $300 the fuhh

Looks like this will be the fix. Will give it a try for the “oldie but a goodie” Honda Pilot!

thanks! simple, clear, NBS instruction.

I just shorted out my whole engine jumping that relay... thanks pal !

If this happens, you most likely have a bad connector at the low or high pressure switch on the hard lines of the condenser. I have had this happen 3 times so far. Wiggle those connectors. If it causes the compressor clutch to kick in,,, that's your problem!!!!!!!!!! You can try replacing the relay, but I would bet against it. If it does fix it,,, great, but if it don't, check these connectors. When you pull it off,,, you'll typically see burning marks. They use under rated connectors for these connections and are under a lot of vibrational influences. Good luck and God speed.

Thanks, I was quoted for labor only $175 plus $40 original toyota parts. it took me about 40 minutes to replace it myself for free.

I wish i watched this video first. I watched another video and it was not as detailed and did not show how to remove the bulb. I had a hard time trying to remove the bulb but your video actually shows it.

Thank you for this video.question has this sensor cleaning on fuel consumption?

Fixed it right up! Thanks!

Went from struggling for 25 minutes to watching ur video and doing It in 30 seconds, no exaggeration.

Where did you get the terminals ?

Let me ask you a question. In my case the clutch and the condenser fan work only if I apply ground from external cable to the main lines that go to them. Is this a relay problem? Unfortunately I can’t upload pics or videos to show you what I’m talking about.

Excellent video! Don’t think I could have done it without it. I like that you got straight to work without a lot of extra talk too. Nice job on the install.

vids like this are why UA-cam is awesome. thank you so much.

Thank you so much for this video.

All the cars has a/c relay? I have a 2021 Nissan versa and I can’t see any relays only 2 fuses

Same pin number on other 4 and 5 pin relays 30 and 87

❤❤❤❤❤

Hello Sir what kind of car is it please👌🙏🙌 do you have any electric diagram for Scion XA 006 from the wire goes to compressor toward outside & inside toward off & on swich under the redio please👌🙏🙌 . I do thank you for your response 🇺🇸 USA 🫵🫶 your vidio🙏🎉

Excelente video e información. Thank you for sharing.

Good job!

Link is no longer working, please share the bulb name :)

So if it clicks on and off with it removed on and off on and off. But doesn’t when installed what does that mean?

Thaaaaaank you !! I have this car for 3 years, I finally managed to connect, thanks to you🤝😌

Impact Wrench is what I needed 👍🏼 Great video!

Thank you, I was able to change my blades without further blood loss after watching your video.

Dang I think I can do that now

brilliant help

Thanks so so much! Still rocking this old beast of a car. :). Just ordered both items.

Thank you so much for this!

Thanks for the video. Couple of questions. Once the truck has been remotely started from the outside of the truck, then i get in, do i then need to place the key into the ignition and turn to "on" position in order to drive? Have you heard of or experienced any problems with seat or steering wheel controls once installed and working? Do you happen to know the max range at which the remote starting kit works? Thanks in advance!

Very helpful 👌

When I jump with wire compressor starts working just fine , but once I put back the relay some times it works and most times it doesn’t … I already changed the pressure switches and still have the same issues, don’t know what to do now 😅… any suggestions!!

Brother can you update product link. Is not working

does the engine stay running when you open the drivers door?

And thanks for the vid... Why do shops charge $600 for this?

Should the coils be changed when changing the spark plugs?

Thank you very much good video

You've got dandruff all over your dash dude ?

This doesn't help locate the wire under the dash.

This is the best video of someone working on this car

Also MG Fuse 7.5A would not allow power to Clutch.

Excellent just what I was looking for

Man I wish every UA-cam tutorial was this simple. Thank you so much.