Відео

Nice and beautiful flight in a wonderful landscape. Great job! Liked & subscribed. Keep it up! 👍

Super

do you know how to switch between bluetooth and line in? I accidently pressed some combination of buttons and now it wont connect to Bluetooth- when i turn it on it says LINE IN and wont connect to my bluetooth- i dont have ANYTHING plugged int the line in port

Excellent. 🎉

Bissiness krein. Kaam Acha hi naee boht acba he

Beautiful bnate ho 😂

Wao. Quit dog

Boht hi 😅beautiful

Aap boht acha kaam kerte mashallah 🎉

Zaberdust 🎉 kaam he wao

Vary good excellent

🎉good hobby

Could you give a quick rundown on how you achieved it?

Useless video, annoying sound!

Сколько часов светит фонарик?

I believe you obviously get paid for this because this dryer has fundamental flaw and that is that the filament can only go in one way and the angle of the filament exit needs to be spot on otherwise it will not feed the filament. That means that the dryer has to be exactly positioned. The fact that you did not mention this is concerning.

😱 𝕡𝕣𝕠𝕞𝕠𝕤𝕞

You shouldn’t have had to read the manual. I have never seen any other machine the required you to “double tap” to turn on and off. Stupid design.

Nice

👍

Great

What solution do you use?

thank you for your review, great you spent the time to really break down the pros of the printer

I need help after leveling it. I attempt to print and the z motor raises again when i select a test print and then starts feeding out the filament above the glass plate instead on on it idk what I’m doing wrong

Nativity Piece is dope! Where is file from? Also the drain holes are the made in slicer or is that all post print?

Any further thoughts 8 months later in terms of quality of the product, competitors and whether you would still recommend this printer? Many thanks for the video.

This video is very good .... good job

Apna pak bhai ha.. Good work I bought it last week same printer. Now trying to understand how to setup. Thanks

Nice

Unprepared

Good Evening UA-cam. While out "Thrift Store" shopping@my local Savers thrift store I ran across this little Gem called Marnur I had No Idea what IT WAS. But I knew I was gonna purchase it. And I did purchade this awesome Neck * Shoulder massager It's awesome! It gives a DEEP INTENSE KNEADING EFFECT with inferred heating Do soothing and relaxing. Best $5.000 spent in awhile!.

God bless you tomouch insha'Allah

Hard work 💪☺️ God bless you tomouch insha'Allah

Very nice 👌👍 ilike

ah yes, I have a rebel xt and a porsche, thank you

You really shouldn't be moving the nozzle across the bed during bed leveling because if it's too close you can make a good scratch on your fresh new bed. Raise the Z by a few mm via the lcd then move x/y and then lower z back to 0.

this is like watching paint dry, very boring. please take this video off youtube!

aceton cleaner,and later polishing with textile ,rleft side is that ruber seal i dint get it compet clean , i buyed a unsed newcondition 4 days ago.

Hello Mate, Could you please post that Sliced print (or anything already sliced for this Printer)? I am looking for it to run a Test Print on my printer as all the Prints thus Far are just Flat with nothing else printing except for the Flat Base. Please help...

Assembling this right now... thanks for the help

aliexpress. Talk about rolling the dice.

good video

my sd card reader broke, it just spits the card out.... is there a way. to print by just USB?

Thank you so much this is my first printer and the instructions I found to be terrible with words like twich paper. You have cleared up the problem I had in a clear and straight forward way thank you again pal

Mashallah you are doing good hobby

God bless you

Best 👍

Mashallah Very good

Beautiful 🥰