Відео

Thank you so much for making this video. I can make it to work tomorrow. I fucking appreciate you dude

Keep up the good work Bro 😊😊😊

Thank you for posting your video. I am not mechanically inclined, however I followed your easy to follow clear steps and instructions and saved $600 dollars I don’t have. Praying blessings over your life and everyone you love, in Jesus name! Amen!

Saved my ass! And yeah, I’ll get a new cylinder too. But driving thanks to you guys! ❤

Thank you!!! Saved me from a big headache!!!😊

Did the trick! Thanks

This literally just saved me! No warning and my ignition crapped out today. Thank you so much!!!!

Takes about 30 minutes to complete. Saved my butt. Thank you

When it comes to the first roll pin, Will that method work if the wheel is locked?

Thanks for making this

I've watched 4 of these different videos so far and your is by far the best one of them all. I really had my doubts when it came to taking the push pin out of the cylinder. It looked to me like "yeah right" that will work. But I was wrong, very wrong. I didn't have my screwdriver exactly in the same place as you I had mine down just a bit and used mostly the cylinder itself. But the pushing and taping and it poped right out. Nice job,

Literally worked exactly like described. Got me out of a $550 part before labor.

I did all this it started now a/c and radio not working afterwards

Thanks for this great video. I was able to help out one of the waitresses at my favourite restaurant and got major brownie points with the staff 😆. She had a few people try and help her and was about to have it towed to the dealer. One little thing, I believe the spring goes on top of the steering lock lever, not underneath it.

Heads up guys, as already noted, the first roll pin ABSOLUTELY WILL NOT COME OUT as easily as vid shows. Can't comment on the rest. Been stuck at pin removal for 3 hours

So for people that can’t fix it themselves. How much would it cost at the dealership for them to fix it?

YOU THE MAN!!!! This must happen often, small town Alaska O’Reiley’s has the entire steering column lock mechanism for $432. Took about an hour from start to finish! Thanks so much!!

Yep, thanks for the info. Mine had the same problem, but not any more!

Just wanna thx you man you save me a towing and like a day lost of work. I just did remove the key assembly and bring it to a keymaker, voila. No towing no hassle, i even could remove the broken car in the winter driveway to every one in the family get to work tomorow morning 🙏👌

thanks a million buddy car was stuck sideways in front of the garage. wife couldn't pull in. the procedure went just the way you filmed it(except when some tumblers fell out which you warned) back in biz thanks again man

So do I need to buy a complete cylinder from Honda or no? Sorry I'm in the middle of this right now

Great video! I have been working on this today. I’m wondering, did you put the roll pin back in before you put the ignition back into its original place. I’m at this point, everything is working, but I’m nervous putting everything back in, without the roll pin in. Please let me know. Thank you, Bronson

Thank you. Wife was afraid to drive the car as sometimes the key wouldn't turn. I bought the core assembly with keys ( $21.00 on Amazon) and moved the chips to the new keys. This video was very helpful with the remove and replace procedures. Key slides right in and turns easily. Happy wife, happy life.

So the one that keeps popping up do we take it out and leave it?

Thank you for posting this video, it saved me a ton of time

Thank you! I could move the key just enough that I didn’t have to drill a hole to get the little pin out. I so appreciate this video. I basically have it memorized now I watched it so many times. Hoping this fix will last longer than the car so we don’t have to buy the $400 part.

Thank you so much for this terrific video. Just resolved the problem on a 2003 Element. Had to remove all the tumblers! But it’s rolling again. Great step by step.

Nice detailed video for a PITA problem. Did you try any graphite or lubricant before disassembling the cylinder? It seems like that one tumbler wasn't bent or damaged so why do you think it seized up? I've seen lots of people experiencing the same issue. I'm guessing maybe people in dusty or dirty environments might have a higher probability of having this happening.

Plus one on the the assist for this! Followed your directions pretty much to a T and success! We're on the road again. At the 1:50-2:20 mark, I wasn't having much luck. Took a really close look at the pin that holds it in and wiggled it out a little with an awl and a push pin, and it finally came loose. Not quite as forcefully as your video, but she finally came out. Thanks for the vid, saved me a bunch of $ and time!

Hey thank you for the great vid! Started to get a sticky tumbler, knew it'd be no fun but better now while I was at home w tools. TIP: set pin didn't budge, no matter the tapping etc. Drilled the hole up to the end of it so I could see what I was doing, then drilled the pin a little with a tiny drill bit- once bit jammed in the pin it pulled out very easily. Also didn't fall/go missing

And I don't CARE IF YOU ARE ALRIGHT WITH Whatever OR WHATEVER YOU THINK MAN FOR REAL SAUL YOU BROKE MY SPIRIT MY HEART AND NOW I HAVE TO FIGHT TO SEE MY OWN CHILDREN FOR REAL YOUR FOWL LIKE FOR REAL

Awesome vid!!!! Thanks for the help!!!

So, what if I can't get the key all the way in?

This was a huge help!!! Thank you!!

This worked for me. Thank you sooo much! You da man!

Dam.. so basically your saying I should blow this car up and hope someone sees the smoke to rescue us? 😂

I can’t get the roll pin out and I’m ready to cry. You made it looks so easy! I’ve been whacking away for an hour!

I unlocked my steering wheel adjustment, and jammed the steering whell up and down while turning the key at the same time, it worked! I think it seized up when I turned off the car with the wheel turn all the way to one side.

The best informative video it worked!

I wonder because I had tried spraying some WD-40 in there cuz I did not know what the problem was but I think that doing that has prevented me from being able to get this release pin to vibrate-out like you were able to.

im having such trouble after taking the ignition cover off, hammering the keyhole in and prying it but it just wont come out, is there a certain technique you did with this?

fixed

This is really helpful. I just got stuck in a small town with the same problem, and I'm trying to avoid it in the future. quick question for you: at about 2:40 you mentioned that you had to drill a hole to remove a roll pin. how would you have solved that problem when you were stuck at the chiro? is there another way to remove the roll pin if I'm stuck without a drill?

chiro is looking out at the the guy twisting himself into his driver seat floor just shaking his head. So helpful, thank you!

I got stuck 9 hours away from home this would have saved me

So you took out the bad pin, or tumbler but what did you put in its place?

Can I remove all the wafers and be done with it?

Thanks for the video!

Should you disconnect the battery before disconnecting the wires?

Wow that first roll pin popped right out allowing the switch to jump right out. That was much easier than drilling a hole. Maybe I just got lucky but thanks for that trick. I lost the roll pin but bought another one. Good video, thanks.