Відео

Thank you so much for this video! It helped me through the full installation of my mailbox.

I think he mixed up the RO membrane with the deionizer While he points to the RO Housing and then the RO membrane, I’m not sure if he has a deionizer. A deionizer usually has a mix of both positive(+) and negative(-) resin, that’s to be replaced frequently, if it’s not in a larger vessel than the usual RO Housings. RO Housings usually start off the standard of 1812/2012 which house RO membranes of 1.8” W x 12” H and 2.0” W x 12” H. The inlets being 1/8” NPT to 1/4” OD, so all are paired with 1/8” NPT to 1/4” OD. Different than the Housing Inlets and outlets of a 3012 Housing. 1812/2012 RO Housings are paired with membranes ranging in pressure from a minimum of 40-80 PSI with most having that optimal 60 PSI. 1812/2012 also range from 24 GPD(Gallons Per Day) to 150 GPD, depending on the make, etc. There’s also 3012 but that usually requires more pressure; 80-100 PSI, and sometimes 3/8” OD NSF certified Tubing compared to the 1812/2012 which are typically paired with fittings of 1/4” OD, Push to Connect. While a 3012 can come with 1/4” OD Elbow Fitting, and the Inlet is 1/4”, most seen to come with a 1/4”NPT to 3/8” OD Elbow Fitting for the inlet. The 1/4” NPT end being towards the inlet of course, and the 3/8” towards the OD, which doesn’t really make much sense, as the flow might be greater but that would decrease the PSI, unless you’d want a greater flow while lowering the PSI to get the PSI higher at the end, as it seems this apartment might have a pressure regulator, as there seems to be no way to increase the pressure beyond what’s being measured coming out. If not then it makes it a bit weird. Does it seem to cheaper? Cause if that’s paired with an Auto Shut off switch, the auto shut off switch either comes with 1/4” Inlets/Outlet Or with 3/8” Inlets/Outlet. There doesn’t seem to be an auto shut off switch where some inlets are 3/8” and some outlet are 1/4” Either way most seem to be outsourced, the systems that includes the membranes to. It’s an interesting topic for sure. As there’s many things to learn with RO, which goes into Water Treatment. As with RO membranes they last either 6 months or 2 years, depending on water quality or the Pre-treatment one does before it reaches the RO Membrane. An example being UV With dual lamps of 185/254 nm wavelengths at a minimum of 11-12 Watts to be effective in its performance against bacteria and organics, this paired with Ultrafiltration of 0.1-0.01 micrometers or microns is an effective pretreatment to the water before it gets to the RO Membrane. After there’s always carbon and maybe re-mineralizing your RO Water etc.

Very helpful

Maybe worth mentioning that the small blue tank is only used when using the handheld wand. The small blue Oxi clean tank is not used when using the main floor head.

Just a note for some installers : helpful to use nut drivers to tighten many of those screws instead of screwdrivers, especially with the blind spots and lack of space/visibility. There will be an option for many of the clamp screws (especially) that come with most disposals.

Your not doing the concrete correctly. It'll be brittle and weak if not mixed. The concrete around the outside will harden a bit, but the center will not get enough water even if you let it soak for days since not enough water mixes into it. This is only slightly better than just using plain soil.

Well done. Told me exactly what to do and when to do it. Thank you.

You needed a lot more water than that

Nice job on the video on how to change out the lawn mower blades. I just bought the mower and will be changing to the bagging blade. I read the operators manual and will be adding Torquing step to all three nuts/bolts to the recommended factory specs. Center bolt torque setting is 36-43 ft-lb (50-60 N.m.) and two side bolts require torque setting of 22 ft-lb (30N.m.). Maybe you can edit video and add Note across last part of video with torque specs.

I was going to ask how come you didn't use gravel and I guess the answer would be because your post is metal and not wood correct?

Could you please tell me the bolts size? mine came with the wrong ones and I can’t attach the mailbox to the pole

Great video Kev. I was worried about relying on just the switch to control electricity but I saw you recommended cutting power at the fusebox.

Thank you. I'm hoping to replace mine this summer and this was very helpful.

Great Job 👍👍 Is the metal post hallow? The reason I'm asking is that I already have a round metal post in concreat, and want to slide the new post over the existing smaller post....and then I'll secure it.

Promo-SM 😈

Great instructions the best yet I wish EGO would not have put the bolts on so tight frustrating

Dont you have bigger than that..for packaging post.. Thank you.❤

I see you didn’t use a torque wrench, I thought that was overkill! Thanks

There no square for light fixture

Torque to 40 ft-lb on center bolt is critical. Too tight and you fatigue bolt. Too loose and could come apart. Both center and two outside bolt are in millimeters. Manufacturers don’t switch up from inch to metric. Wear gloves.

Great vid Kev!

Hey kev it's kc, first viewer.

the sizes are 9/16 and 17 mm for correct fit.

That Blendtec Jar is not 90 oz.

Even if you think you do not need them you should be wearing gloves when changing blades, one slip of the wrench and you could get a serious injury.

The instructions recommend using a torque wrench… any particular reason you don’t use one?

WAGO 221 LEVER-NUTS Compact Splicing Wire Connectors are a lot safer and easier than those screw connectors and electrical tape.

Its good that you removed the battery first 👍

Can the mulching blade be used for bagging grass?

You don’t torque per the owners manual?

Thank you for this video. Feel like I spent way too long searching for someone to do this correctly and most importantly cut right to the chase.

Nice job but I think you’re not supposed to change the color selector while the light is on.

Nice review brother. Keep it up 🤙

Do you have to reinsert the mulching blade or can you just use the single extended runtime blade by itself on this mower?

Good job buddy.

Your doing gods work brother thank you

Never have used a Blendtec, but my Vitamix does EVERYTHING I have ever wanted a blender to do. And I would rather have SWITCHES than BUTTONS. VITAMIX BLENDER jars are made of a material similar to airplane windshields, from what I read.

not a fair test at all...people don't do 10 second smoothies as they should be about 45 to work properly. .

That was a great video, thanks!

You can buy a tamper and top with a larger opening for the tamper for the Blendtec Total Classic from Amazon for just a few dollars. With these, the Blendtec has the same good results.

Because you’re using a different model on the vitamix but there is some vitamix that do have the button for what you’re doing. I have one of them.

useful thank you

I was just looking for a video JUST like this :) Thank you

Thank you for watching this video. Please feel free to leave a comment and I will be happy to respond to you if you have any questions, etc.