Відео

I’ll be danged. I tried it and it worked. So easy!!

Beginner here, I wanted to stain my floor black as I did i paint it on and let it dry without wiping (i had no clue what I was doing) now the whole floor is pure back which is nice but sticky ish, how should I go about it now, re sand floor or just just paint gloss over but I'm afraid gloss will melt the stain off 😂 thank you

You saved me the biggest headache of my life, and a good amount of money on replacing components, as soon as I cut that white wire on pin number 10 the parasitic draw vanished, another problem with the eBay harness is that the transmission connector is not wired properlyand it puts the transmission in limp mode, there is a white wire that's taped up right before the connector that is not installed, and there is another wire installed in the wrong spot,

I love simple solutions to pain in the ass problems, thank you.

I have worked at a desk with a specific "U" shaped form for a big embroidery machine since they are so expensive, and i tought i ruined the varnish job. THANK YOU SO MUCH !!

this is exactly what I needed👍

Tried it on our sticky tabletop that we left too much excess stain on and it worked perfect! Thank you!

Thank you for making this video!

Thank you !

Thank you! Saved me

I sand with 120g. Everything I stain with dark walnut, I find that it always feels greasy after a few days of drying. I cannot figure out how to stop this. I wipe while staining. Still greasy.

How long should I wait after doing this to apply the polyurethane?

Awesome thank-you! Forgot to wipe the third coat of stain down and remained tacky. Went back over with more stain and then a clean cloth…problem solved! Thumbs 👍🏻

I did the same thing with Tung oil on all my new oak hardwood floors. Finished a bit too fine, left it soak too long, now 5 days later the floor is still a bit oily. Based on your experience i’ll go over with a terry towel mop soaked in orange solvent, hoping it’ll remove the oily layer 😂

That’s wild you found more than you threw down. Great vid

Thanks man!

Thank you, I’m wondering why the stain was still sticky after 3 days

Have you ever tried using mineral spirits? I'm in the situation I don't want to use more stain because I don't want it getting darker. I'm not sure if mineral spirits would remove too much or if it would be ok as long as I don't use too much. I may have to intentionally repeat the problem on a sample piece to test the theory.

Very helpful video for me. Addresses the problems I came into and some solutions. Thanks for the honest video.

Can this pump be used to completely suck out a septic tank and portable toilet? For example, if air gets inside during the last drops of water, it runs dry afterward to make things clean and dry. The client checks after me to ensure the job is done perfectly, so I need a pump like this that can completely clean a 200L toilet reservoir. Thanks

It’s been probably 100 hours and there is still some spots on a firearm wood varnish that I am staining that are tacky. What happens if you just leave it, will it never dry?

You should of made a video of belt routing my guy

I’ve searched for hours for an explanation on this. Thank you! Plenty of posts out there on the forums about this issue but no one explains why or how to fix it.

Thanks for the tip, I ran into that exact issue 👍

Beautiful set up 💪🏻

Dude thank you. I'm having an issue with my board not getting dark enough and I'm think I need to leave the stain on for way longer then recommended (at least an hour), but I'm afraid of it becoming tacky and messing it all up. Now I feel more confident that i can undo it but also get this damn thing to turn dark!

Never heard of 175 grit sandpaper.

I love how in love you are with your elephant ears ... I have the giant variety and they mean the world to me!

Thx so much! I needed this!

I spilled a can of ready seal on the stack of plywood 😮and im facing this all the oil and stain seeped into that one side of 8 boards

This video saved my project! Thank you so much!

Wax free shellac will seal the stain , varnish with waterborne product

Will this let you suck up mud too?

Beautiful fish ❤😊

Damn… I was having this issue and should of just checked UA-cam now I stained it a third time and it’s super dark and it was an oil based 🙄

Excellent!!

Great explanation. Question: Small rocks. Is the pump/suction weak enough to not pick them up?

Those fishies are livin the good life. 🐠 🎉

Hi. Not sure if you read these. I left a comment on your wood stain video talking about tackiness. Please help if you can.

Hi. We used a white paint and primer and then stained our table. We found a great video on YT for that. The table was tacky, the minwax wood finish was used. We used the mineral spirits like you recommended and reapplied the wood stain. This was last night and the table is still tacky but not as much this time. I’m wondering if we didn’t leave enough time in between the mineral spirits and the stain we reapplied. I dont know what to do. I don’t want to sand it again. So do you think I didn’t leave enough time or is it possibly something else? Please help me

Lookin great brother!

Cut out the bad language.

thanks for making the video good info. for the neg comments.... make your own videos

Thank you, your video was just what i needed to hear. I've been working on my stairs, a learning experience and work in progress. I have two steps that are tacky and didn't know how to fix the problem. I can now progress to the poly. 😊

Not a pro of course and the same thing happened to me Thanks for making the videos it surely helped me!

smashed it 🔥🔥❤

Add a ball valve to pipe to control flow. And you can start it when it is at bottom

THANK YOU! Your video & info just saved my exterior door. I’ve already put so much time into this as I had to stripe 8,000 layers of paint off of it. Thx again!!

This helped me sooo much. My mineral spirits scraping wasn’t as effective as I had hoped. You saved my shelves.

Thank you! Refinishing a new teak shower mat that I want darker... ❤Jenny in Boston, Massachusetts