Відео

Will a 15hp 1998 apply with same parts? Or similar

Thank you 😊

Should do it in english 😢

I might be buying a Dufour 31 on June 29, 2024 in Puerto Rico. I will be watching all your videos. Ivan Laracuente

The “notch” called …..woodruff key .

FINE BUSINESS! The "NOTCH" for the impeller is known in Canada and U.S. of A. as a WOODRUFF KEY! CHEERS from HERE!

Hi, Is it the orignal Dufour 31 pulpit ? Cool it allows access from the bow. Do you know if it can be found somewhere? Br

NOTE! The gearhouse/lower unit shall be in upright position when you fil it whit oil.

Very nice to have George Kniest (watersportshop) around ;-) Could you name the exact materials used? VHB typenumber. Als curious where you obtained the windows, since I am also replacing mine. Thanks!

why do you have a longer tube that connects to the water tube (the tell tale tube) mine is just a little fitting

Hoi, andre hier, we kennen elkaar van de overdracht van de boot in muiderzand. Leuke filmpjes, hier kunnen we wat mee wanneer wij eraan gaan klussen binnenkort, zag dat jij al aardig wat werk hebt gedaan dus dat scheelt weer. Hoe gaat het inmiddels met je been, al wat vooruitgang?

Good luck.

Jammer zeg! Wens je spoedig herstel en snel een volgende boot! 🙏🤙⛵

Ek vertou jy gaan gou herstel. Maak jy darm 'n wins op die verkoop van jou boot?

Jammer…spoedig herstel!

Sad news, but you need to take care of yourself. Rest up, and you will be sailing in no time.

Hello dear followers, While typing this description, it's sad, but also nice. It's nice to realize that I came this far without much experience. I've manage to buy a sailyacht, to improve a LOT and enjoy it a summer. It's sad because my first surgery knee construction has failed (broken) and everything needed to be done again. I've just had that 2nd surgery and coming 7/8 months are going to be harder. In order to NOT step on the boat again (very tempting) I've chosen to SELL the Dufour 31. I'm 100% sure that coming sumer there will be a smaller sailboat again, but my recovery needs to be done first. This is my main focus :)! Enjoy the last short episode! CIAO!

I REEEEAAAALLLLY wish you would have shown how to disassemble the shift rod.

All good 👍 12:52pm

Amazing video! Thanks :) I arrived here because after mounting I don't know exactly until where the nut of the gears should be adjusted. All the way through? Somewhere in the middle? I've did the test that I'm neutral is loose and otherwise is stuck, but when turning on and switching gears I hear clancking sounds, like it's not shifted properly and then it goes off... So I'm just guessing I need to screw it more

Hello ! Glad to see you again on the sea ! I’m the proud owner of the same ship as you, since 2020. A dufour31 from 1975. Thanks for all your tricks, you taught me some interesting ones ! We are learning to sail and doing our best to fix it. As you, we love it so we understand perfectly every smile you make on your vidéo. Thank you for your happiness !

You have a nice boat and a very nice car - enjoy.😀👍⛵️

Why were you sailing with the Genoa alone without the mainsail - you had some great wind and a good point of sail (beam reach). It’s great to see the progress on the boat.😀👍⛵️

Do you know you can get an attachment to dispense detergent that attaches to the pressure washer?

To refit the mast, repair the roller furler, rewire and rerig with new rigging for around €2000 is cheap as chips.

Good video.👍

I too joined after Marks post but loving your posts and now watching both ❤

Maybe consider thread lock for anchor fitting ?

Hola, yo tengo un dufour31 igual que el tuyo , tienes el despiece de la caña del timón ? Planos? Para quitar la mecha y quitar la holgura? Gracias

An FYI for everyone facing this replacement. If you don't have a Yamaha dealer in your town, and must resort to mail order, I would avoid aftermarket impellers. There are 100 different sellers on Amazon pushing aftermarket water pump parts, and they are all of dubious reliability and durability. I've tried a few of these, and they often fail in less than an hour of run time. If you paid less than $35 for an impeller, and it doesn't say "Genuine Yamaha" on the packaging, it's probably not going to last very long. Also, when the presenter says "notch" in this video, what he means is "Woodruff Key". The "notch" is the slot in the shaft that the Woodruff key fits into.

Came over from Wildingsailing - subscribed.😀⛵️👍

And thats not where drained the air from

Try replacing the copper washers😅 or test the fuel lines pressure tester

You are very brave to take on such a huge project!

Looks like a great day to be sailing!

Hi nice videos and content, I need your help with the yamaha 9.9 check your instagram please when you get a chance

Very helpful

Thanks for vid. My windows are sika flex and screws. Some rust is showing. I want to use the 3 m tape and primer. My windows are oblong and rounded not square. (click my icon to see). Does this tape bend around? Just wondering how I will put tape on the rounded ends of my windows. Thanks in advance.... Gary in British Columbia

😬

This looks like a strange way to do it. Typically before removing the lower unit you put the gear in reverse, then separare the linkage. Once it is separate you can put the gear in neutral using your gear shifter. That will create a gap between the upper and lower linkage. Once re-installing the lower unit again you can fully push it in place and torque the bolts before reconnecting the linkage. Use the gear shifter to put the gear in reverse and the two linkages with be brought together so you you can get the big nut onto the lower linkage. You can keep the lock nut on the linkage. The lock nut will pass through the rig when you remove the lower unit.

Leuk. Waarmee maak je die kaartjes bevat je route?

Promo>SM

I agree with the previous comment. The only thing between that sensor & the hull will be some sort of sealant. That could give way at any time leaving a bigger hole in your boat. Fill the hole with glass and then cut a new one the correct size. just sayin.

how did you get the prop bearing housing off?

Do you have a cold start switch on yours?

Great video! 👌👍

Living the dream dude! Awesome - Clinton in Sydney Australia

I don't understand why you would remove an LED bulb to replace it with a regular bulb?

Owning a boat will not bankrupt you but the overpriced cost of spare parts and marina costs will.

That hole is far too big for the speed sensor, you would be better to fill the hole, re-glass it inside and out, and then cut a new hole for the sensor. or you may find it leaks when you least want it to, Just saying better to be safe than sorry.