Відео

Replacing the upper intermediate steering shaft with a sound insulated (with a rubber sleeve) one from Borgeson worked totally for me.

Not sure how this video only got 50 likes

Can I put an r18a2 jdm engine in my r18a1 car? Engine is bad so I bought the jdm a2 just wanna know what to expect

some AC clutches come with spacer washers inside, in those cases would you recommend just to sand or grind down only the spacer washers?

Does the stone scuff up the upholstery?

I use wet and forget. A little more expensive but it last for years because it reactivates after every rain.

I’m about to do this my 03 civic does this

I believe foam cannons typically have an output ratio of 1:10, meaning that if you use the strongest bleach available at 12%, then you'd only be getting about 1.2% down on the roof, which is a little on the weak side. Clorox outdoor is about 8%, so you were only putting down about 0.8% bleach, while I believe most softwashers put down closer to 2.5%. Great idea, but this method may not be as affective.

I know this is an old video but thank you. I’ll be doing this later this evening.

Thanks for this video. I can’t stand that thing. I wonder if a heat gun might be able to help mold the floor mat a little better. I might have to try it on mine.

I work at a shop busted the tire and put it back on but couldn't get the beam to take air in the tire how can I get it to take air

Lol now a good deal on these is $3500

300 mile changes, they look just like that. Why i do every 300 miles. Only use amsoil

This is a great hack. My 05 civic has 200k on it and the ac stopped working. Was going to buy a new compressor but I’m definitely trying this first!

Hey I have a 2005 Honda civic lx did a full jdm engine and transmission and it’s not shifting properly…it’s like u press the accelerator and the rpms just keep going and doesn’t shift until you take the foot off the accelerator

Mine started doing it around 500 miles. Dealership had no idea what to do about it, so I just ignored it. The truck’s gone now though. I got a 2024 now. Almost 8000 miles so far, not a single issue.

Thank u shawn.. that was a awesome video .. i showed the video to my car mechanic. Told him do exactly as u did on the video.. work like a charm...even the mechanic was surprised... thanks once again...❤❤❤❤

Love that truck 😊

I've watched like 80 videos and was wondering why arent any of these d1ldos using a foam canon

What headers are those? I just got the engine but I’m looking for the right set of headers

Is this literally a drop in swap? I have d15b1 w matching trans to put into an 02 civic and thought I was gonna need the whole drivetrain from a crx

Dude this is gold. Just what I was looking for. Thank you!!

Nice little trick!!! My clutch isn’t engaging, so im gonna give it a look see and ill let y’all know what happens!! Subbed!

Is it fast

Hi just wanted to ask did you swap some sensors from the old ones, if so what sensors did you swap

My 2007 silverado 1500 has the same problrm , i was going to buy a 2024 chev truck , dam they had this problem too long and should have be fixed by now, and i only got 49,786 miles chev is crap

Where are you located? Please fix my car! I'm in Villa Rica GA

holy smokes mate, i did this 6 months ago and its still holding

My clutch is still engaging but warm air at idle. But when I am driving, or sitting still holding the rpm’s up it will blow cold also. Will this work for that?

WHY D3 NOT SELECTED PLZ

THEN YOU CAN TELL CUSTOMERS THAT YOU HAD TO RECALIBRATE THE NEUTRAL BEARINGS THAT WERE OUT OF LINE OF THE WATER PUMP MODULATOR WHICH SENT PRESSURE TO THE COMPRESSOR SPARK PLUGS SO DON'T NEED TO BUY A NEW ONE WHICH SAVED YOU AT LEAST A THOUSAND DOLLARS OFF THIS TOTAL OF $3500 BILL ! YOUR LUCKY DAY !

When I tried to loosen the 14 mm, it just free spins cause the clutch is not engaged. How do you take it off?

It's been a while since you got this, is it still going? Thanks for posting.

Hey man. I have 1998 prelude with a F20b motor. The car runs pretty good but the car feels like it's not getting power sometimes, like hesitation. I think it might be something with the fuel because I'm only getting like 130 miles on a tank. I juat got in a fuel pressure regulator that I'm going to put on tomorrow. What else do you think it could be?

K20/24 set up 06-11 civic si * Do yourself a favor and grind it down It works 100% Did mine like 8-9 months ago and got zero issues , just cold air blowing in my face , w my blunt 🕺🏻🕺🏻🕺🏻

I’m getting p1705 code I’ve tried adjusting the part on video but every time I put into drive it blinks and throws the code. I have jdm motor and trans. Help

I have a 97 Honda CRV first generation that's doing the same thing I wonder will this fix my problem

Ive got a d15b7 out of a 93 del sol. If i swapped the intake over would it run in one of those?

Having the same issue with my 1997 Honda CRV wondering if this could be the problem as the power steering fluid has leaked all over the top of the compressor but I will try this

What about on a 1997 Honda

Thanks for sharing this wonderful product with us.

Good video what lift you running

I am going to instal one in a 95 chevy silverado 2wd tdi but will i have to do a commputer delete or change wiring harnes it my first swap its getting here next week?

Ohh man. Im starting to get these just now. I dont have any issues with my AC but these fixes are quite good to know. I have seen many upset people who coplain how their AC ain't working. When i bought my car i started to read ins and outs how things work as people are forced to buy new parts when old ones get a bit dirty or wear out a bit. Now days there are clutch kits on ebay that you can replace the worn out parts. But this is also a good fix for a buddy who just has a case of beer and promise you will have it if you fix hes shit.

Hey man! Are you still on here I was wondering if you can use this product on polished chrome ?

Thank you i’ve been looking for something like this. I’ll look more onto it

You save my life had a shitty impact an couldn't get it tight

Time to invest in an impact wrench 🤣

Somebody said it's like a plastic bushing at the firewall.

I use the xjet for the sh but i think i like the idea of using the cannon just for the surfactant