Відео

What do I do if the previous owner (or whoever) glued the screw that holds the spindle in place? 😬

Hi, Adam, I have a Kenwood KD-5070 Turntable, but, for a few months now I have had a problem with the turntable. Do you know how to solve this problem? I will appreciate if you share the solution. ua-cam.com/video/5SsH-F6arrA/v-deo.html

I can't see, if there is a 4th which is a bearings ball? That came out of my piece, when I cleaned it.

How to get the stand by off how to reset my Kenwood stereo receiver

There is no problem playing it. Only when rewinding the tape stops before it reaches the beginning. Is the problem with the belt?

A great and easy instruction.

You didnt mention the ball bearing in the bottom of the pot???

Thank you very much! Five star work!Greetings from Portugal!

Love it. Thanks so much. Can't wait to try.

Great instruction, I fixed the spindle in 15 minutes. Thanks!

how did you get it to work dude? mine has LOW SOUND! trying to get it to work.

Absolute Star

Nice video. Great job. Thanks. Any idea how to release the spring loaded black hinge that supports the dust cover tabs please on the back of the chassis of the tt? One has snapped (not on dust cover tabs) . Cheers

Thanks helped a lot.

Hello! Thank you so much for this video! not many take aparts on youtube. I know this video was a while ago. Was hoping to get your 2 cents here if you have time :) I have an issue where i'm getting buzz through the same Kenwood KD-3070. When I have my turntable going > phono > amplifier I get a buzz that increases with my volume. when using another turntable (RT-85) at the beginning of the chain there is no buzz, with same headshell. When touching the RCA connectors with my fingers the buzz gets louder. Also when hearing the same buzz when unplugging my turntables power adapter. The RCA cables which were just replaced by a tech. No buzz on his test bench. I've tried moving the turntable to a different location. tried bypassing my external phono and going directly to the built in phono on my integrated amplifier. I'm assuming the cables that were installed aren't properly shielded? I'm wondering if there are other work arounds besides replacing another cable.

My motor doesn't change speed no matter what 😃 and I dont see anything on the board to where else it could be

I got my pl12d mk2 today from marketplace for 25$! Veneer and dust cover is dusty but sound. Gonna service it tomorrow.

Great tutorial! I would suggest laying a dry cotton towel over the transformer so it's impossible to get shocked.

Perfect. Thank you, the video was helpful.

All Aiwa devices written with a lower case letter aiwa are devices produced after the takeover by Sony. This was the beginning of the end of Aiwa, which produced very good HFi devices. A great loss for fans of the Aiwa brand from its glory years.😢

No effing way! I didn't even search kenwood or the model number! That's it! I got 2 of these broken...thanks 😊👍

Hooray! Got my craigslist Pioneer 12d working beautifully now!

........very tricky......nice going........kenwood design philosophy..?.....just design it super quirky.....no charge...!!......great vid..!!

❤Thank you for such an informative video. Your review helped me understand my new soldering kit. I had looked at other reviews but none were as helpful as yours. Blessings and Thank you from Weslaco Texas in the Rio Grande Valley. RB

Do you still have this deck? I have one and the motor is noisy. When you switch the unit on the capstan is permanently rotating. Is it normal?

to loud for a small apartment? to much base for apartment? mostly want it for cinema and video games. I have the fluance elite for a few days now because i was worried these might have been to much now i dont know.

Real quick: What's the purpose of a preamp? My vinyl player doesn't need one. Vintage pioneer.

Where can I get a new balance pot for my 3020a ?

Hello, Thank you for posting this great video. I would like to make these repairs to my own turntable but found that the eBay store you’ve recommended is now sold out. Can you recommend another supplier for these parts? Please respond. Thank you!

Thanks! Grettings from Brazil!

Brilliant, I’ve just fixed mine following this video. Very helpful thanks!

Ive just got a belt pack for my f810. The tape mechanism is idential to your 850. One belt is slighlty bigger then the other. Which belt goes where?

Thanks. Very helpful! 🙂

Thanks so much for this video Fixed mine today and got it spinning Loving listening to my re olds again I had to add a 1/8 th inch ball bearing

I have the same model. It stopped working the other day, found the belt had stretched out. But your video helped me with the spindle. Probably never removed since the factory. It was a fight to get it separated! But now it's clean and lubed, the platter spins super nice. Just waiting for the new belt.

Great video! So if playing too fast, a slight turn to left will slow it down?

REMEMBER THE TINY BEARING AT THE BOTTOM OF THE SHAFT. BE CAREFUL PULLING THE SPINDLE OUT.

Adding some late information regarding the ball bearing that's at the bottom inside the spindle sleeve: There is a replaceable ball bearing (standard 1/8th inch). In many cases you may not realise this because it can become embedded in solidified grease which you will clean away and it will just look like a smooth point when you look inside ... so don't give up until you work it free. The bearing can acquire wear. Without the belt attached these turntable platters should spin for a long long time! Modern synthetic cycle grease/oil should make the bearing last for ever. Now you know what to do you can give it another service in about 25 years! I bought mine in 1973. (Also, I should comment that folded paper towel is too risky to use between grips and spindle ... as shown by someone in the comments who damaged his spindle using that method.)

I was having a heck of a time with my deck until watching this video. Thx for the service.

i would like to kiss u maaan!!! all people comment on the web to change the belt..and u made me discover that HUGE little tiny magic switch.Grazie 1000!!! my technics on oliver tree pumping like never

Thank you! Everyone-watch this video first. Best on the subject!

What does it mean when I turn Mt amp on and it says protection mode good video Cheers

Thank you for the great overview. I received this kit today and found your information very helpful. Thanks again.

Cuanto cuesta

Hello Adam. Do you know if the Technics SL B210 uses the same type of gear?

Thanks for this video, really comprehensive. I was able to refurb my SL-B2 with this and it's like new again.

Step 1: clean the pot using IPA Step 2: lubricate the motor(bearings) Step 3: Adjust using a testtape. If you don't, you're not taking in acount drag . Problem with that is: speedfluctuation due to the fact the bearing and the shaft cause wow and flutter and the motor will need to overcome too much mechanical resistance (wear) By having cleaned the pot, the adjustment will be easier and more accurate. The motor (and soundguality) will be thankful.

Do you have any suggestions on how to replace the dampers in the springs? Or what material to use?

I've just had the same issue with an Aiwa ADF910 belt like tar. I use acetone (nail varnish remover) which I find better than isopropanal alcohol, it's also great for sticker residue!!

What was the user error if you remember? I’m having the same issue