Відео

Where can I buy this product?

Can you put this on top of TPO?

@ 1:04 i noticed that if you don’t pre-drill the screw holes, your likely to break the vinyl trim as seen @ 1:04. Pretty brittle stuff

I thought that you only need one screw in the center to fasten it, not on the ends as he said.That way it can expand in either direction????

My wife and I are looking at doing a horizontal fence using Hoft posts. She like the looks of your hollow UH02 in Walnut. Do you have any recommendations?

How do you install these over the concrete patio stairs and the raisers?

Number 667 like had to do away with that 666 bruh 😂

I measure 13/16 in finish trim, but setting posts in concrete to 24 9/16 , 😂

I’m installing this right now as ceiling soffits. Looks great.

Shitty explanation

So confusing

Are there color matched screw plugs for the caribbean blue deck boards? An, no routed the entire length of the board. That's something I didn't know. I wish the caribbean blue was available on Columbus profile, but I will have to route for the fastenters since I don't want visible screws. Don't think I could get that L-shaped groove carved in to the Cortes board Unless I could fit a dremel blade in somehow. Would be a pain, but I could possibly do it, but then would need to get some sealant inside where I cut. I want to make a small landing outside an exterior door but need to figure out the measurements and how many boards I would need. Again, I wish fascia board was available in the caribbean blue. Is it just an unpopular color? I suppose worst case I can use primed PVC boards and then paint them for some of the edges and for riser covers on the stairs. For people who aren't using boards on the sides, it would be nice to get some sort of end caps for the Magellan and Columbus boards. Although, I suppose it would look nicer to use boards on the edge and miter them to hide the edges, but not everyone will want to do that. Shoutout to Richard Lam for answering my e-mails and giving me some info on the router bit size (1/4") and letting me know that some of the boards are not available in the caribbean blue.

Can this be installed directly over joists of a deck, or does this need decking installed below it for structural integrity?

Why do you need furring strips if the clips already create a 1/4" air gap?

Great video, but if you are installing cladding between brick, or gable, how do you install end trim?

Gotta love how they dont tell you anywhere, on their videos or website, of how to cut them with a curve. Not all decks are square, some are rounded.....

I don’t know but this material scratches easily. Currently installing one.

Doesn’t at all tell you how to install

Are there levelling plates for uneven surfaces?

Trying this tomorrow ill let you know how it goes

What about freezing if water gets trapped under will it lift and break.

@ 3:30 I dunno if I like that 1 inch gap under the window. Shoulda started off a tad higher there “licensed contractor” 😅

What color is shown at the beginning of the video :37 second in?

I'm considering composite siding for my home. This looks like a neat product.

I sure would have applied some stain or paint to that old wood under the deckwood. But not my old deck that looks on the verge of collapsing.

NICE!

You know it looks real when it looks like it needs a good dethatching lol.

Product is discontinued.

I agree . They are hard and screws fail. I ended using a larger drill bit and then worked just fine . Wish they would have just made holes on the rail to post diagrams . I used a drill bit to make holes on cardboard diagram and sort of worked

Can you use this on outdoor covered patio ceiling?

How much wound this cost ?

What is the trim for the windows... And how do you make a block for the lights

When the wall is very high, how is the union of one piece to the other installed in the european style siding

Not as easy as it looks. Those posts are hard to drill pilots into. I went through several $9 bits designed for metal drill into these things. The 7/64 pilot is too small for the self-drilling screws they provide and they are prone to strip. I changed to hex-head self-drilling screws to make installation much more manageable. I really dislike the screws they provide, they have flat ends, and are unable to find purchase in the pilot holes you drilled. Very difficult to screw in straight. The paper templates are not centered along the fold so if you follow the directions your posts will be off-center. You must mark a center line on the post and the template if you want a centered post. Learned this the hard way.

Why are they open at the ends. Bees in our area will be a problem.

Ok

are the hot in the summer sun?

can this be hung on the ceiling?

Now you can afford chairs!!

Those hole templates do not line up correctly. Very frustrating to use it and find that each facing side of the post is off from the other.

my concern would be high wind resistance of these products!?..☹️

Definitely doing this to my deck stairs

Can it replace outdoor brick paving? ?

Where can this be bought in eastern canada

i have no idea what they are selling here...hubba hubba!

Love NewTech. All of it is great for quality, look, durability, installation, etc. However -- No end caps for starter boards. So all my boards have end caps except for the first and last boards on the deck. ????