Відео

It’s crazy that it’s smaller too

what size is your canva project?

Nice work!

No usefull information for the beginner, and the music just gets in the way.

How do you know what size template to use to design your art for the bottom?

I’m Utah local :) where are you located?!

If you are having problems with the laser engrave with the blue light. instead of doing 2 passes with the blue light, try doing a second pass with the ir laser as it really cleans up the engrave

Thanks for showing this. I have the same laser. How are you focused so far away? Did you change the lens on the laser? Mine has to be practically touching whatever it is lasering. Very annoying and is really my main complaint about this laser.

how long did that take on the F1, I did a knife and took forever. Had to buy an ultra

Great Video! What type of water laser do you use?

where do i shop- for bulk order for stanley cups?

Is it possible to do a full wrap using D1 10W on the 40oz tumblers? I’m having a lot of issues because of the tapered part that is further from the laser 😔

How long In average takes to engrave a tumbler like yours?

What are your settings used?

You might want to take your time when uploading your video, and double check the upload quality, some of your most recent videos are uploaded with a max resolution of 240p, which would be ok if it were still 1999.

Good videos but they are too blurry

What are your power/speed settings? And what is the wattage output for your laser?

What Xtook model in this video?

качество видео соответствует картинке на кружке)

cool video , but blurry and you not saying what you do

Nice video 😍

WOW! THEY LOOK AMAZING!! WHAT SETTINGS DO YOU USE?

What's your engraver? I'm looking to invest in one

How do handle the smell?

If you run a second pass on the F1 using the IR laser at half the power of the Diode and leave the other settings the same, the IR laser will clean up the engrave leaving it nice and shiny without the need to use the magic eraser sponge which can dull the finish the cups.

What rotary accessory is that. Is it xTool or a compatible one?

Great job 👏🏽. Can you share your settings for the S1? And what watt it is.

Can you do a full wrap on a 40oz with the F1?

Great tutorial! Thank you

music so bad lol

do you buy your tumblers in bulk and if so where do you get them?

the enterior tile under the F1 removes to balance the RA2 on. Use the notches on the pad to line the RA2 striaght. Settings for F1 RA is blue light: 80 power, 400 speed, 300 lines per inch. then second pass is IR 40 power, 400 speed, 300 lines per inch. makes real crisp lines.

Where do you get your Stanley cups? These turned out great. I am using the xtool S1 to do some tumblers.

How do I order a lid for my winter pink 40 ounce Stanley?

This is so helpful and thank you!

Run a second pass using IR power 40, speed 400, and dpi at 300. It'll clean it up really nice.

Very Nice!

Interesting! How did you deal with the different focal depths?

What settings did you use?

Hi do you always have to take handles off?

Awesome work! How long does it take for the top part please? I recon 30 min? Also what are dimensions for the top part. I have f1 and wanna try tomorrow but not sure what’s the design dimensions to put on top?

Are you having any issue with words coming out backwards using the rotary?

Zero information on how to engrave your own tumblers....

What is the speed and power you are using

Is that the 40watt you’re running at 100 power?

I recently purchased the Xtool M1 with the RA2 Pro. I have been purchasing some tumbler designs that are already made. I have seen some say that you can tilt the bottom of the tapered tumblers like the Stanley 40oz. I have seen others say that it’s best to do the top first and bottom second but some of the designs are florals that start the stems at the bottom and go all the way to the top so I don’t know how I could do that. What do you recommend? I just found your channel today and I love it. Lots of the videos I’ve found use LightBurn and it’s hard to find people do tutorials on the Xtool software.

Cant hear you over the music

What settings are you using? I can see your power is 100 but I can’t tell what you are using for the speed and line/cm.

Can you do a full wrap on a 40oz using the xtool d1 laser?

Why not just refocus the botton, rather than run twice