Відео

when I get the E90 I just unplug from outlet for 30 sec and plug back in and unit resets itself E90 goes away. I change filters every 30 days

this video was worthless. It could have been 30 seconds long.

These pumps are definitely not $50 anymore. Those were the good ol' days, I guess. Today, they're $160 on Amazon. Today, the shaft is $8. I'll try shaft first. Thanks for the video!

My issue is that pieces of the coating in the pipes/lines (black material) is chunking off and I think that's clogged my pump. I'm worried that even if I replace the pump I will still have that issue.

Replaced the pump and still have an E90 code. So it’s not a bulletproof fix. I think it may be the control board now. Sucks that it lasts only 2 years. Also their tech support sucks and is useless.

i have the same problem. i pulled the pump fan out of the magnetic field and cleaned it up i also used a paper towel(dry) and cleaned the inside of the magnetic field. its working but i am still ordering a new pump

Hey berry I go a great solution for heating up your spa when you have drain it and start over with new water or reheat your existing water .? What I do is fill my spa , with water that is heated up to 110* degree water coming from your garden hose and ran thru a propane heater used for taking hot showers when you go camping these little portable units run off of a 5 gallon propane tank and heat the water from your garden hose one past thru snd puts out 90 to 120 degrees water continuously until your spa is full and the is hot and ready to go as soon as its filled up. Cost you no electricity to heat it up and takes about 30 min to be fully heated and ready to go.? Costs you only about 1 gallon of propane.? After that you put the spa back up to its normal location on to the pump. Recommend CoscosX model 8L 41000 btu. Water output up to 113 F 1.58 GPM comes with propane hose And regulator. Purchase on line Amazon Cost &129.95. And the bonus is its portable so yoi can have hot showers if you go camping

WELL done. Needed this. 🔧🪛

Thank you!

Is there a link to purchase this pump?

Yeah not 50 dollars anynore

Can you provide the link for the pump

Do you have the link or the part number to replace the pump and do you have a video on how to replace the pump?

Will this fix the air jets? My filter pump works and heat but the air jets do not turn on at all.

Thanks Barry that was great that you slowed it down. Most of these guys are just playing the song and not showing how its done the way you broke it down.

This is very helpful

Why would I get this after only using this for a month and even then it's only used on weekends? Seems odd to replace a pump after 1 month use

do you have a part number for the pump motor? thank you

Great video and advice. That said, I ran the unit with both filters and the return taken off for 5 minutes (after bubble purging also), changed the 2 filters which were only in for a few weeks and looked pretty good and that solved my problem. The return being removed alone did nothing to help. There was also a little bit of black pudding skin like guck returned into the main tub area that I see from time to time. I am thinking it’s residue from the internal pump area as the filter would def. Catch it from going in. Bottom line is clean water and filters sometimes makes all the difference.

Great video good information thx!

Yeah those are junk. Mine has E90 code the first day. Just don't buy this find different company.

Yeah, but i keep getting the E90 error code three times and I've only had the hot tub for about 5 days

Where do i buy a replacement pump?

Dirty filters will give the same error code, I changed mine and it works fine now

Where’s the link

I am not getting an E90 error, but the pump stops working after a few minutes. Could this be the same problem?

Got the pump, replace filters. Things suck… idk what to do now

Filter should be on the bottom pipe not on the top he is filtering water afterit been through the pump so all the muck gets into the pump

How do you get the case off to get to the pump. I have a pump in hand but either the case is stuck or I am doing it wrong. Removed four screws on the case do I have to disconnect the pipes as well?

What's the link for the pump for spa pure plus motor? Please and thank you 😊 🙏

I’m a machinist so I made a shaft out of true 316 stainless and solved the problem forever 🤷

I have the same spa, the customer service was quick! I love my spa!

Had mine for 5-months before pump quit working couple weeks ago with E90 code. Spent $120 on eBay for new pump and I still get E90. What a rip.

I got e90 and the spa ain't but 2 weeks old yay coleman was better.

Wrong out is the top bottom in...

I cannot figure out how to take the bottom/housing off! can you help? do i have to disconnect it all? what screws to undo, etc?

Very helpful video! My pump got to where it wouldn't restart if it turned off. But, I took it apart and tapping on the motor would get it to start. The shaft and propeller looked great so I lubed the shaft and "spinny" parts with Vasoline and for now it seems to be working normally again. I may need to replace the motor in the future but my tub is only a year old.

This is a great lesson, but don't you think it would have been a better idea to have used a 4-string bass instead? Most of the people watching would be using 4-string basses.

Ive had this spa for three days and I got the E90 error tonight. UGH!

We don't need watch your face but your right and left hand, and we cannot watch your right hand. Verdine never palyed a 5 strings bass.

On mine it only took unscrewing the water flow system and putting it back on.

I have only had mine for not even 2 months and I have had that e90 error code come up three times already. It did it again last night and this morning I did change my filters and I got the beeping to stop again but I have a feeling it will come back I don't know. I took off the filter and I can feel the suction coming out of there so I know that is working but my filter light will no longer light up not even when I press it? Do you know what is going on there

Definitely right about the worthlessness of warranties...

I got that code. Cleaned my filters. Only put filter back on intake. But...let it run a minute without filters because air was in the pump. Running fine since for $0.

This is absolutely the simplest and most correct fix. After realizing the common problem and the easy cost effective solution, I bought two new pumps through INTEX… Payed the same amount in shipping for two of them versus just one… Shocking. Put my new pump in in just a few minutes, and I am right back in business. Trying to do any fix it to these cheap small pumps is a waste of time. The investment is minimal for new pumps, and so is the time it takes to install a new one and be right back in business. This video is the best of all of them!!

Hi thank you so much for the info. I get the E90 code everyday when I turn the filter on. The filter is dirty so after I put a new one in, it works fine. Do you think I need a new filter pump. My spa is 1 year old?

Mannnn you made this sooo easy. I appreciate you sooo much.

I was also hoping you could show us how to change the pump.

Do you have the link for the pump

I just replaced my filters with new ones then reset it all fixed