Відео

Great ideas thank you for sharing them 👍🏼🦌💯

Thank you from canada

Would this issue cause no power to my car when I have the key in run position ?

I search UA-cam for this video each time I need to drop the deck. Very good explanation of how to remove. This is a super "how to" video. Much thanks.

Could not remember where that small rod on the back was supposed to sit but I knew someone you UA-cam would have my back. Thank you, sir!

Saw your video about a year ago. Finally have a deer feeder (to feed feral cats) and have run into the jamming problem. I had to hunt for the video but now it will be put to use. Thanks.

Im put ting a bigger wench on my xmr1000 21, i put the rope on mine i don't like im going back to the cable good video, im also putting 1 on the rear , my bike

Very helpful!

Thank you Sir. I have the same mower that needs a new belt and blades.

😤🤡🖕🕳💣💨👮‍♂👮‍♂👮‍♂👮‍♂👮‍♂👮‍♂👮‍♂👮‍♂👮‍♂👮‍♂👮‍♂👮‍♂👮‍♂👮‍♂👮‍♂👮‍♂👮‍♂👮‍♂👮‍♂👮‍♂👮‍♂

If you're gonna drive your tractor around with your deck off take out your rod that holds the front of your deck cause if not you'll bend your rod and jack knife your tractor that won't be good

Good afternoon Pitt I'm Brendon when you reinstall your deck face your pins backwards cause most of the time you go forward and your pins are facing forward there's a chance they can pop out and your hangers come down that won't be good but when you face them backwards if they hit something they push in take note of that

I have several feeders, but the one I started with years ago, is still hanging around. It's the plastic Game Winner 200# tripod and I'm going to make that plexiglass spy window cutout. Great idea. Thanks for sharing.

I wonder why moultrie that makes the feed make a spin plate that dose

Nice !! I like how ya did it one handed , very helpful . Now I know I don’t have to put my beer down 😂😂…. Very helpful , doesn’t look like they changed much from last years model 👊🏼👊🏼

Nice video , thanks

👍

Very helpful!!! Thank you sir

Although I am a female, I am expected to be dumb. Thank you sir for your video out of about six videos south watched yours is the only one that showed me how to remove the rod on the back. Your lovely man thank you.

Awesome video! Thank for this valuable information. This video just saved me some money.

Thank you!!

For longevity, the deck should be removed every time after mowing to clean, coat with oil, add a pump of grease to the spindles and sharpen the blades as needed. Can hit 30 years of life with a stamped deck.

Good simple video. Thanks.

Any updates on this? Is it still working?

I need a picture of the wiring

Wait is the wiring harness color to show me

Life saver thank you I’m a assembler

Thanks for that. For some reason I ended up with 7 clips. An extra small one. I could not figure out where it went. From your video it seems I have an extra clip. I'm guessing the previous owner must have dropped one and replaced it with a new clip. Removing the deck dislodged it from wherever it had fallen. Thanks again.

Well done video! Wish I had watched it first! I had a large pin clip left over on reinstall. Your video reminded me where it went! It was the one you didn't remove holding front deck rod from removal front side. Thank You!

Man, these are genius modifications. I have a Moultrie steel barrel feeder and it's jamming. I will have to try this. Great video and tutorial!

have the same problem with my feeder

Must i disconect battery

We’ll done

Thank you my brother, you helped my mother out with the information from this video. Thanks again

Thank you so much for this video!! I’m moving and couldn’t fit my lawn mower through the gate, so this video helped me so much!

Saved the day thank you!

This is exactly wha my ford focus 2010 doing rn!! I thought it was a electric problem.. saved the day literally.. we thought it was the battery so we brought a new battery for no reason last night 🤦🏾‍♂️ thanks again!

I think you are you should send you some too you know what you're talking about we have a good instruction good great voice and I think since that was your first video you did great and I think if you own it to make it a little more cleaner straightforward a better camera angles you are great person to listen to I appreciate you in Jesus name

Thanks for the video !

Hi Pitt. Your video showed me where the one piece I couldn't figure out was suppose to go. (The triangulation "cross beam"). Thanks.

Excellent work, explanation and video, sir! Thank you very much for putting this up!

Thanks for the video. I thought I took enough pictures when taking it apart to remember where everything goes 2 or 3 days later when the parts come in. I couldn't remember how that last bar your removed from the back went. Helped a lot. Well done.

A number of goat owners are trying to adapt this. The problem with sweet feeds it does not work consistently. This might be helpful or using a 12 volt motor and controller

thank you for taking the time to make the video

The location of that sway bar was grieving me NUTS! Thanks

Just what I was looking for. Thanks so much.

Put clean corn it in corn that dirty will cause that

Is it the 3/8 t40

Excellent video!

Thankyou great video helpful