Відео

I used this for my last oil change in my 2012 toyota venza/camry engine. It stopped my car from burning oil and smoking upon cranking, also gave it superb power.

upgrade the fuel pump!!

How did that end up working g you had me cracking up with the Ching Chong Chang Ching 😂

Grab 2 pieces of 2x4 and drop the trans on it. It'll click eventually. That's how we used to do it back in the day

Are you using a 10:1 fmu ?

Nice.Turbo hondas for the win

Plastic mallet and grab a fella to hold the ring open give it a wiggle and line up the dowels

I've taken apart meny honda transmission auto and standard. The problem I see your having is the bearing that sets the locking ring clip in place is not open enough when you close the case. The best way to do it is to line up the case hole with the locking nut just enough to where you see to edge of the nut. Then take a big flat head to spread the clip open the pull up on the locking nut with another flat head and it should lock in place. Best of luck have a great one.

I used a sledge hammer and jb weld.

gotta use a blue impact driver with a white socket and screw at it

Did you have to shave the inside of your block to make these fit or rotate?

Good stuff man

What is your fuel pressure regulator set at?

Awesome vid man! Got a procharged build here. How would I prime the FMU for 5-7 psi?

Manual cars for the win

That's why people that don't know how to build transmissions shouldn't touch I'll tell you how to do it. Turn the transmission upside down and bounce it on the table. It will snap right in

Modify some snap ring pliers with a grinder. Make little notches in the tips so the snap ring doesnt slip off the pliers so easily. Snap rings suck.

What was the compression results?

It actually uses copper silver and lead and not minerals to help the rings seal rhe walls. That’s what the with CSL stands for

Great video - thanks for breaking it down

I see you out here! I just got a dx that i'm'a put too much love in to. Thanks for the advise!

Make your 2d fuel graph as linear as possible you have fuel cells from different coloums overlapping other fuel columns based off map load amd rpm... I understand the car might not see parts of that map and not even touch those cells but all in all the car will be that much more safer, reliable, and just fells like a smoother ride and transition.... Even ramping up.. Whatever fuel curve / torque curve that fuel map is taking...make them most consistent with that curve in the low, mid, than higher load parts on the map.....if you gonto your 3d graph....u can really see how smooth of a fuel map your really have.....

Perfectly said

I used this i was smart enough too not over fill my engine with oil over the max limit all ways drain 1 quart of oil out first 🤣lke that stuff dose work

Thanks brother🙏🏻 got all the above waiting for the 50mm socket and 19mm. Throwing a VMS pulley with my tune ⚙️ nice DOHC u got there✌🏻🌵

my jeep has 178k miles and does NOT burn any oil thats because oil was changed on time every time but it does has a noise by now underneat when cold so i decided to buy engine restore to try it out every day since that a have oil prreshure light on when i start the car i figured it clouged the filter so i had to drain that shlt

Im in the process of putting my turbo kit on my crx and suggestions

You dumped oil in without knowing how much was there first. Thats your smoking issue.

Good mtb bikes too❤🎉

It's not supposed to seal leaks from worn out piston rings..what a idiot

Its for sale on offer up now

Smoked because you over filled it.

I have used this on numerous vehicles with no issues. It has to be usere error. I mixed it with only high quality oil amsoil or valvoline.

Good video sir, By any chance invite you to do a product review, We specifically produce LEDs for auto. How can we connect with u?

Put the wrech in the pull up position and use a jack to push the wrench up for you why struggle use your brain

When I still had my D-series, I bought one from Amazon for $60 bucks. Started throwing codes and misfired. I returned it and bought a legit one, and never had a problem again. It’s honestly a hit or miss, but I’d rather hit consistently lol

But your car is nice

Bro what's in your hand that's a dirty or something

Head gasket leaking

You are doing it the hard way get a ratchet with that thick 19 mm place it between the frame of the car bump the engine in that nut will come off

Amazing video easy to follow along!

Fast EF sedan. If you see grey seat cloth in a junkyard I need a driver side !

Im curious as to how these pistons held up? And they go ona b series?

Hey i used this on my 2 vehicles a nissan tiida and a suzuki grand vitara which had a slight bearing knock i have not had any issues in fact the bearing noise actually stopped so it really works..

Since this machine does open the injectors full open without pulsing them How do you calcul the Lb/hr

I used this some, seems like it helps some but limited, I thinking smoking and and oil leak is from you over filling it, you just dump the bottle in and 2 quarts of oil without checking the level, and recheck the compression ether.

I just got a bottle of this for my 1992 Oldsmobile Royale 88 LS. Two of the cylinders have like half compression from what I was told. Now I'm wondering on even adding it

It works on cylinder walls, if you're compression issue is a valve then no it won't work.

Hello. My vehicle is civic 1.5 t 10th. I downloaded 21 starter maps, but the region I live in is 980 meters above sea level. That's why it doesn't go above 19 psi. What can I do about this?

Pretty sure my tranny isn't in the best shape either