Відео

How have u added that oil cooler to the bike ? Can u show me, please

Fuckin weapon

I just found one of these things and I can’t wait to work on it 🎉

Are you concerned about starving the crank and oe system without a deeper pan or aftermarket hiflo oil pump?

Dyno results ? Before After ?

I need to get this done on my 2008 R1

What size dump tube do you use on the hypergate 45? And what size vband clamp to install the tube

sooo what your saying for the turbo flutter ... i have to unplug the n75/solenoid.?

I’m about to build my 2004 with 51,000 miles. Full rebuild turbo etc. Any advice you can give me ? Best Map tune and also injector cc size? I want about 300hp just smoke check these new bmws😂😂😂😈😈😈

I’m looking at building a turbo 05 r1! Any tips from going through it once? What’re you doing for tuning once it’s running?

hey brother, nices videos!!! whats upp with the gt650r??

Adicione legendas em português por favor

TURBO R1??

📸

I didn't even know the horn didn't work 😂

Think you could do a timing kit walkthrough?

Do u have a video of how you connect it to the rack on The back what fitting did u use ?

How much more HP u got from this?

That engine sounds like it needs a cam chain kit

Billet?

Sir I want job your geraj have chnce

que modelo es la bomba necesito una igual para mi 08 r1

What if I put this « kompressor » on my A4 1.9 tdi

Какая новая максимальная скорость

More 6a13tt content pleaseee!!!

Hello, how did u removed the plastic silencer from the front part of supercharger, that one part with the plastic thingy holded by 5 T25 screws

Sorry for the big comment, I like your videos. I have the same bike and the response is crazy with those modes. Keep up the good job!

I strongly not recommend to weld those washers as you destroy the balance of the basket and the result will be very painful for your unbalanced shaft .This engine is very sensitive on the rods bearings so don't be surprised if you hear a rattling noise after some km depends how much you push the bike. Your fuel pump also need replace, measure the pressure on the fuel line, should be 3.5 bar and yous probably reach 2.5-2.7 max. The best modes for this bike for reliability and massive different on the acceleration is : - 1st convert the chain to 520 stainless steel sprocket at the front and an aluminum sprocket on the back with the same teeth as the bike comes from the factory - 2nd replace the rods with CP Carillo rodes same travel, before you install them send them for balancing. - 3rd replace the clutch for a racing one (lighter and stiffer). - 4th replace the fuel pump for an Quantum it will keep the pressure to 3.5 - 3.8 bars when you hit high RPMs ( believe this bike suffers with the stock pump) - 5th replace the y pipe with and aftermarket without the catalyst converter - 6th increase the fuel supply to the maximum from the speedometer. - 7thOPTIONAL mods (if you have to spend more money) replace the slipons with aftermarket and fit a power Commander and tune the bike properly) - 8th if you want to go further change the exhaust manifold with an aftermarket recommended for this bike if you do that you need to change the camshafts as well otherwise the back pressure will decrease dramatically as the new exhaust manifold will have slightly bigger diameter pipes. You will get 200 to 205 HP at the wheel. Without the 8th mode you will get about 185 HP at the wheel. For sure you will suffer more on the suspensions.And the modes for the suspension are quiet expensive. What you achieve ? A more reliable engine and a bike 17 years old that can execute 2024 super sport bike easy as the power from the engine travel faster to the wheel through the lighter parts.

Bro where'd ypu get the fuel loop from

Loving the 6A13 content mate! They are rods from a company RPW in Western Aus who get them made overseas. I have heard there can be variances in roundness, so I would advise just to check over them for roundness 😊 Side note, they should have gone single turbo 😉

Would 100% like if the video was a bit longer. No hate for the length of the video now but not many people are recording them building a 6A13TT engine so it's very nice to see people keeping them japanese cars alive!!!! Great work man! Keep up the perfect content !!!

so good seeing all the parts laid out like that :)

Camera angle was way better for this one, keep it coming man!

Ugh great time to remind me I still need to put my kelford cams in mine. 😅 And my twin plate....and fix my shifter brackets on the gearbox....and rebuild my transfer case.

Legnoom ❤

How is it holding so far ? And could a titanium wrap work on a titanium exhaust? Assuming you are using fiberglass wrap Also what’s the amount of wrap that you needed for the job ? Thank you in advance

How is it holding so far ? And could a titanium wrap work on a titanium exhaust? Assuming you are using fiberglass wrap Also what’s the amount of wrap that you needed for the job ? Thank you in advance

Legnum balls

The Legend has posted, keep up the vr4 content so helpful 🙏

Might need to point the camera down a bit further throughout the teardowns, it felt like I couldn't see what you were doing, still really excited to see the rest of it. Love from the NT

I will watch literally as much content on the vr4 as you can make

Awesome stuff just bought my second VR4 post more Legnum content!

How was the low speed drivability with the exup deleted. Ive read mix reviews about deleting it. Gonna do it to my 04 5vy r1....

Anyupdate what happend about this mercedes

Whats your business called and where is it located?

What cams are you using ?

Brother, I put the high pressure line on the bottom and that fought back like you said.

when will you make a video on throttle body synch?

You might be keen to watch my vids on my C32 AMG its getting twin turbski's compound Super charger in the next couple months.

Why is he mumbling , cant hear a word