![Kirk Brooks](/img/default-banner.jpg)
- 26
- 98 182
Kirk Brooks
Приєднався 20 кві 2014
Barudan S Head Needle Bar Driver Replacement
This video shows how to remove needle bars, replace a needle bar driver, set needle depth and jump timing, and put it all back together.
Переглядів: 21 337
Відео
Rotating a design for flats
Переглядів 1566 років тому
How to rotate a design for sewing on flat garments.
Puting the machine into drive mode
Переглядів 2396 років тому
How to put the machine into drive mode from standby mode.
Inserting design to machine memory
Переглядів 1556 років тому
How to insert a design to machine memory using a usb stick.
Hoop Selection
Переглядів 1576 років тому
How to select a hoop that you will use and view the design in it, and auto center the design in the hoop.
To Back the machine up
Переглядів 1316 років тому
How to back the machine up to repair a broken thread.
Switching from hats to Flats
Переглядів 2176 років тому
Switching from the hat drive to the flat frame on a X series 9 needle Barudan machine.
Switch from flats to hats
Переглядів 5566 років тому
How to switch from sewing flats to hats on a X series 9 needle barudan machine.
Puting the flat frame on
Переглядів 786 років тому
How to put the flat frame on a X series single head.
Changing the Speed
Переглядів 4746 років тому
How to change the sewing speed on a X series barudan machine.
Deleting a design from memory
Переглядів 2,1 тис.6 років тому
How to delete a design from memory of a X series Barudan Embroidery Machine
Powering on a Barudan Single head Embroidery Machine
Переглядів 3,8 тис.6 років тому
What you will see and hear when powering on your machine.
Barudan: Switching From Flats to Caps
Переглядів 3,7 тис.8 років тому
Barudan: Switching From Flats to Caps
Barudan: Switching From Caps to Flats
Переглядів 4868 років тому
Barudan: Switching From Caps to Flats
Wanted to post here and say what ended up being the issue with my machine, D05 error Behind head number 1 there are pairs of sensors attached to the frame which the computer uses to detect which needle you're aligned with. There is a small metal piece attached to the back of head 1 which sits between the pair of sensors which correspond to each needle bar. If this metal piece is bent out of place, your needle position will read N0 on the screen and you will first get the D01 error, then D05 once you line up the color change lock. To fix it you can simply bend the metal piece back into position taking care to align with the correct pair of sensors for the needle bar your machine is set to. If you did this right the needle position on screen will change to the correct number and you'll be able to change colors and run files again. Either way this video helped me learn a lot about how my machine works! Thank you!
Hi, if anyone else gets a D03 error like I did on a multihead, go to the head 1 and rotate the dial (it's got these two big screws on either side of it) on the right inner side near the needle bar so its vertical, turn off and on the machine. Then it should work. If this isn't enough, turn all heads on and go to the "Manual" page and keep pressing the pin in/out button, make sure it can go in and out on each head. Then do a manual color change, this is what fixed it for me... 😁
can you make a video how it should look from the front plate view. Thanks
Thanks
Can u do a video on how to replace a needle bar stopper?
Hi sir to solve board of the embroidery machine “Barudan” there is a two bottoms we have to click it together for settings of needles To change from 8 needles to 5 needles, l have to go to the settings. First, there are two buttons that must be pressed continuously. The first is the power button, and there is another button. Or two buttons I would like to contact with you if it possible I lost this way do you know it I can upload a video to my channel if I want more clarification to help me please Thank you.
Hey there Kirk! Thanks for the tutorial. Do you think D22 code has anything to do with what you just showed on the video?? Please advise.
What does the needle bar stopper do.. the plastic or rubber roller looking piece? Mine broke.. and now machine won’t always trim..
My needle bar stopper broke too. Did u get any info on how to replace the rubber piece?
I changed the waffle washer, now it won't tighten back up.... tried with new screw....& new knife, It just won't catch... it wont tighten, please help! around the 2 min mark..
Would like to see how to replace the res plastic caps part HT230190 Need bar addy. Barudan elite 2001. Bruce Adams
1:04 saved the day! Thank you!
This morning at work I went to turn on our Barudan single head, and as usual the origin thing prompts on the screen. I hit the button, and the pantograph slides all the way to the back and gets stuck and won’t move forward on it’s own. No settings were changed last time it was on. Tried restarting and unplugging it, keeps doing the same thing. Google is useless for troubleshooting this. Do you have any suggestions???? Thank you in advance!
9 out of 10 times, What about the 1 out 10?Mine wont trim everything new with the exception of the new washer, But it trims the bobbin too short.
👍
How much this mesin
Thanks
Would you happen to know to to fix it when it gives you a code D10 on the machine
Does it matter if you input a cancel code when the screen says extend?
I went through all the steps here in your video, but now, when it starts to run its like the driver isnt getting held out to stay in contact with the needle bars? there is good tension from the spring any ideas?
If you pushed down to much on the pin that holds the needle bar in position, it may stick and not release, so maybe try readjusting it.
@@kirkbrooks101 the needle driver works smoothly, i did have a pin tension issue it was a bent shim i replaced it with the ones Barudan sent me and it worked smoothly. ill have to look into again put a new spring in as well
@@aaronpalmer5782 sometimes the needle bar driver just sucks, I keep a bunch on hand just in case one doesn't want to move freely.
@@kirkbrooks101 yea i could see that since they went to the S style head alot more plastic in here for sure thabks for the help Sir. Hopeing to get down time in production to finish this
ARE you Barudan technician ?
Used to be.
@@kirkbrooks101 I just got single head 15 needles model BEVT, can you do training on the phone by facetime I can pay you , I in California thanks
do you this for each individual needle?
No, once only.
Any suggestions as to why I keep getting d12 error and the trimmer slider keeps getting stuck in the down position? Ive tried loosening tension and the trimmer slider seems to move just fine when i manually move it down. could it be that it is dull and needs to be replaced?
Thanks for this. After doing the replacement I am getting alternating d14 and d3 codes, any suggestions as to how to remedy?
Thank you for making this video. Make more please
Hello my friend. Do you know how I can fix the code D03 on a Barudan 2016 one head? Thanks
👍👍🙏💪
Kirk, thank you so much! I tired the manual...useless. You saved me a lot of time, money, anxiety and stress! Thanks so much!!!
would this be the same as trimmer timing adjustment ?
thanks
hola ,saludos desde Venezuela, el vídeo se ve mal , podrías por favor subirlo de nuevo en mejor calidad, gracias
why you do not take the complete head out ? saves much time...
Thanks for making this video ..as my machine showing D 10 error what's I have to do ? How to repair ?
BIG Thank you!
Thanks for the video. I have done this many times. Today while trying to realign the cutter, once I tighten the screw in the back, the lever still moves freely. Any suggestions?
If the black lever still moves front to back you will have to remove the cover that covers the black lever and you will see another screw that will have to be tightened similar to the one in this video
Kirk Brooks thank you! I will give that a try.
Could some one help me please I have a innovis. V3 embroidery machine I have some designs on a USB stick and I think I might have deleted a design by accident from the stick using the machine have I lost it for good now or can I retrieve it I'm new to this as you can tell
Just What I was looking for. Thanks for the knowledge.
can you do a video on how to update OS for X Series
Very useful vid but the camera angle is not perfect.
How do you enter the sizes for a mighty hoop or a hoop tech clamp?
Gracias for your help!
Thank you for making this video. Hope to see more.
Do you need to change needle plate? How’s the reliability in terms of color change, no needle and main axis error? I’m deciding between ZSK and Barudan. Thanks for any feedback.
There are no needle plate changes. Typically Barudan is the most expensive out there, but you get what you pay for. If you are an experienced operator you should not have any problems all for a minimum of 5 years. Settings and parts will eventually begin to fail and I recommend having a tech go through it at that time so long as you have been cleaning and oiling on a regular basis. You will never go wrong with buying a barudan!
Thanks a lot 👍🏽
Thank you very much for this. It fixed my problem too
First thanks a lot for making this videos, even that I don't own a Barudan, they are great, since there isn't to much videos from a real customer like this one. I wish I could found your videos before I purchased my machine ...ouch! ...just problems since day one, and not problems related to embroidery work, like needles/threads beaks ...etc ...but machines problems. ...so I'm selling it! ...just to save some $$$ ...it has become more expensive, than getting a Tajima or Barudan! Are you using the new Barudan XL2 - BEXT-S901CAII? How do you liked? How reliable is in this machine problems? 1. how often you get main axis (shaft) problems? 2. how often you get color changes problems? 3. how often you get no needle problems sensor? 4. take up lever problems? 5. Does it's really cap friendly? (So far on my research it's at the top) How the maintenance: easy? Can you change the volume of the beeping sound? How big is the shipping crate? Please, I looking forward to your honest feedback, since I'll be seeing them on Friday Sep 7 at the ISS Show in Orlando. Thanks in advance for your help.
Barudan is the best machine out there, and typically the most expensive. They are the best at doing hats for sure. You will not have any of the problems that you say you had with your current machine. I tell people that if you don't smash a hoop everyday, keep it oiled and clean, you should not have to see a tech for up to 5 years. Unfortunately the beep volume cannot be changed. If you talked with Bob at the Orlando show you got good honest information! Good luck
Thanks a lot 👍🏽
Man that's really productive!! Thanks for your videos.
Can you do one on needle depth on newer models?
Thank you fine sir...fixed my problem!
More videos please! Some on the BEXT 1501 CB II
What's your recommend rpm setting for 3d embroidery?
Depends on a lot of things really, but the new machines should be able to handle it up to 1000 rpm
HI Kirk, I think I have the same issue. Here is the video demo: ua-cam.com/video/o9uAWGJY_9E/v-deo.html