Відео

@Korey Freeman, I can not thank you enough. After watching a few other videos, your was simple and right now my 2016 is factory restting thanks to you. Hopefully when finished I can boot past the Android screen! Either way thanks for the video!

Thank you for this video!! I did a bunch of troubleshooting and had a service tech scheduled to come out later today. Disconnect the cable connection for the igniter, blew out the connecter and reconnected the wire. Worked right away!

A good fireplace can't be beat.

On average how many pieces of wood do you use to heat up your cabin in a 24 hour period?

question has anyone encountered the similar menu but without factory reset? I followed the instructions from nvidia website and did a kernel boot recovery then I get the dead android and NO COMMAND error I try pressing the power button for a few seconds but nothing happens .... DOes anyone know the steps to follow at this point ? thanks

Wow dude you spend way to much time on this! #1learn you're stove better #2good dry hardwood is yer best friend and if you have softwood mix it in#3dont be afriad to split wood smaller,as this will avoid lag time.nothing worse than three big hunks hiss and sputter for forty minutes while you're kids &you shiver. Above all lose the wood behind your stove(omg)and don't replace it with wonder board.(tile backer) those white specks in it are styrofoam,half of napalm.after 50 years of heating with wood with various types of stoves I'd liketo think I know what I'm talkin about.there is nothing worse than standing on frozen ground at 3am in sleet hearing your kids cry and seeing the fire department hose your house down.has not happened to me , don't let it happen to you may yer wood be dry and yer pipes be clean,split wood not atoms!

Love the sponsor of the video! haha

First off, amazing guide and video!! I’m building my kids school rink and this answered a lot of my questions. Second of all….the anxiety that kicked in wondering if your daughter was gunna hit the ground swinging was crazy! ha.

I also have this same problem on my Kitchenaid french door fridge. Which of Bondo or JB Weld Steelstik is the better product to cement the grommit with?

Omg.... I have a totally different sparker and after wiggling the cable to make it tighter it finally worked. What a great insight, thanks! I was so tired of cold showers 😆

As a kid years ago I got field and stream magazines. My mom bought 80 in Idaho that were advertised in the classified ads in the back of the magazines. He paid $20 per acre back then for that 80 acres. I sold that property for her in 2002 and it gave her a nice retirement check. I’ve been watching forestry videos too and you should also hack and squirt many of the smaller stuff and trees that look damaged, are crooked or just junk.

I bought the CANLIDI leaf blower here in Thailand for 14 bugs! without battery, but all my 18V Makita knock off batteries fits in. The brushless motor performs incredibly good, on full speed in less than one second. Weight without battery is just two pounds, four pounds with the biggest battery with 20pcs18650s in it. Its loud, but no noticable vibrations, its a pleasure to work with, cause it has so much power this little beast. More machine for less money i never get in my life before.

It runs away fast, right? People don't realize how quickly mother nature will take back over. Dig the video, man.

Funny. We have the same dishwasher. Thanks for the vid!

Great choice of wood stove. The alderlea stoves are fantastic. Great workhorses for applications requiring more significant BTU demands of 3-5 reloads per 24 hours. Cast jacket should produce softer radiation and better direct-to-air heating.

I am curious why you wouldn't load it up completely for the overnight burn? Looks good!

thanks

I have been waiting for 2years, finally my old nvidia works! Thanks!

I’ve only purchased new bumper plates and paid between .55 and .80 per pound for them. I haven’t seen steel that cheap.

Good job. Nice splitter!

Stove top or flue thermometers are a good tool to fine tune your burn. You would probably have a longer more efficient burn of your turned the air down sooner like 15-30 min after reloading.

私も設置しないまま3年が過ぎた28G を所有しています あなたの動画を参考に実践したいと思います

After messing around with the start up processes to gain more ram I must have disabled something important because my shield tv was stuck on android logo. I just factory reset it using the micro usb to usb cable connected to the laptop and it worked. I purchased a usb to usb cable for nothing thinking where the controller gets plugged in is where you make the connection to the laptop but it’s the small micro USB connection in the back that you need to connect with the laptop. Thanks.

Thanks for sharing :)

Sometimes the problem is the igniter wire itself. Check the wire for continuity. The piezo (igniter) can be the issue and the contact on the back end of it. Don’t recommend removing the burner. Might damage the gasket and if you don’t know what you’re doing you could possibly damage it. The thermocouple, burner tube and be careful with the pilot tube. The brass end of the thermocouple can be easy to cross thread so be gentle.

I have this exact mode, and that exact issue right now I'll give this a try. it's been a year, is it still holding?

When I plug mine in it shows the Nvidia logo and then goes to a blank screen, that's it. Now is sitting on a shelf as I went and got an Apple TV.

Worked for me tonight; thank you!

Who needs to heat 🔥 hot water 💧 😂?

Good video, just wondering how you keep your glass so clean? Thanks.

Ive done this process a few times and after a few months, it reverts back to the logo screen. I didn't want to keep setting up all my apps so I just got a Fire TV and moved on.

Saved me $200 service call, you are a hero

Thank you so much for walking us through the procedure. I can confirm that this works with the very first model (2015?), too. Thanks again.

Hell yeah! It fired right up. Thank you for the video sir!

Thank you for the video. Super helpful! One question… I installed a shutoff because I wasn’t sure if the dishwasher could handle constant water pressure, but I would love to not have to shut it on and off every time I use it. Any experience with leaving it under constant pressure? Edit: nevermind. I just saw that you already responded to that question and that it can handle constant pressure. Thank you again for the video!

3 years later, this video still works. Seriously freaking thank you. My cold morning showers are done ✔️

Can you do a little on tutorial on the wiring? Where does that blue wire coming off the battery go?

Thank you! Help at last after one year!🎉

Thank you!!!!!!!!!!

All my jazz bass'es , bridge pu is 1/8 in wider than neck , if yours same size , guess what it is...

What’s the process to remove what’s still screwed to the top of the joist then?

No compass, no problem - Get a couple of plastic mixing bowls one large one small put water in larger bowl, put one pickup in other smaller bowl, place on the water, pickup will orientate North or South. Dab a N or S on with permanent marker.

Thanks this worked for me!

Thanks, mine was stuffed for a couple of months just found your video, wow job done. Thanks again!

Thank you so much!!!!! Thank god for this video!!!

Mine stopped and so I went to Google and found this video. I said surely jiggling a cable will make no difference. When I say it lit immediately, I mean immediately. Thank you

The orange connector was my issue as well. Disconnecting and then reconnecting did the trick. I really appreciate you sharing this info!

I don’t have a pc or laptop and myn is not turning on 😢

That's the 2015 model not the 2017