Відео

I always thought it was better to put on the same stuff that the glass adhesive is on the frame that black stuff

Bruh... You're using someone else's used garbage ebay wide body kit that looks like ass. Maybe you should've fixed your flat tire instead. I bet your that tool that puts a straight pipe on a debaged GT.. Id kick your lame ass out the group..

Where can I get loauver from.for my x type jag

They don't include the adhesive promoter nor even tell you about it because if they did, they wouldn't sell more louvers every time they fly away !!!

T.i.t.s up....thx....just getting ready to install louvers....gonna try this first

Great video! My louver let go i just ordered 30lb gorilla tape . Should i order this stuff as well???

but this is buckled in the middle, bottom

can you still carwSHING?

So i happened to be lucky and snagged one of these amazon louvers for a 2017 wrx but mine dont have the mounting plates i think with the nuts and washers nor the pre drilled holes for them so i had to order the mounting plate $20 and a 3 pack 3m adhesion promoter sponge pack $15 so my $200 louver will look and stay in place and during car washes very convincing to unmount and remount with nuts! My version is telling me apply the 3m strip around the whole louver😅 well if you do that then its permanent, possible failure to drain rain water too.! The moral of the story here is do your homework and do it right especially if its expensive and your committing to it

do you know how to remove the brackets off the glass after using the promoter?

I agree I used the same product on the rear window, problem is the tape stuck to window great but the louver flew off anyway. The metal mount separated from the tape. So next time I will apply promoter to metal mounts to

At what point did you say cleaning back window is a PIA I’m getting rid of these louvers?

How does the promotor affect the glass when it comes to removal and residue?

I noticed the bottom of your louver has already come off

Do you recommend adding promoter onto both sides of the tape?

Make these for Chargers?

So I’m supposed to use the adhesive and the sponge or just one or the other. Which is better

Had my louvers on for maybe a week and a half.... Then one day on the freeway they decided to say byebye to me.... I'll be trying this out

Wow you never said what brand of louvre you used

I couldnt find those adhesive promoters anywhere without having to order online and wait…. So… I went to autozone and bought one of those little mirror mounting kits because it came with a little cloth adhesive promoter with it…. Used that, and so far its worked. 👍

Don’t u need to cut fender to fit 10.5” wide rims?

Would it be possible to bolt the top part of the louver to the end of the roof? I dont like the idea of adhesive by itself

Those look awful, they look too big for the size wheel and tire you have

Use denatured alcohol to strip tge glass. Then clean with windex then promoter

Those are just a little too wide for my taste. I would like to see Flairs that are somewhere between those and Lil Devils

I agree with you on the promoter, I've had mine on for over two year, countless car washings, and still going strong 💪.

Garbage vid

I just did my louvers today, drying right now. But I used the 3M Plastic and emblem adhesion 😝 along with velcro tape.. hope it'll stay on for dear life

Please make a video on how to apply the primer.

Can you open the trunk?

EXTRA TIP: Seal the brackets with RTV silicone for extra waterproof protection!

3m tape takes 20 hours to dry and get stronger

Looks like shit

Thanks for the video, I had the adhesion promoter in the bag but no mention of how and where to use/apply it in the instructions.

Best thing is just buy a widebody scat like i did less headache

does it survive the car wash?

Can I still add my hellcat front splitter after I install it?

Did you cut your fenders?

Do you by can’t chance remember the part number of those 2 clips you clipped together? I bought this kit used and doesn’t have the clip

Nice video thanks

hey great video, just installed louvers on my my 10th gen civic using this promoter and it worked very well. i had a not so good experience using this promoter installing the rain guards though. i got the promotor on my finger and when i installed the rain guard it left my finger print on the guard and i cant get it off. i tried alcohol and acetone but it didnt help. any suggestions? thinking of using tint wrap on the outside of the guard because that will cover my mistake. any help would be appreciated

I’ve lost two of these louvers already. I’m ready to give it another try. Has yours held since you made this video?

Yeah that adhesive promoter is the joint! Shoulda watched this video first before learning the hard way!! 😎👊👊

I drove behind another Challenger with louvers on the freeway last week and I was crushing hard 😂 definitely going to look into getting the MP Concept louver you have (I actually checked them out on the website first before seeing this video so I’m taking it as a sign). One question - can you elaborate on the soap you used to clean?? Which soap exactly? And I’m debating whether I’ll need a rear spoiler too to complete the look... Halp....

That looks horrible...no disrespect just bein honest..

Gorilla glue 😂

Not sure how I feel about this!

My louver (V2 louver from Ikon Motorsports) didn't come with mount pods or screws. The only option was crappy two-sided tape and the louver came off after a couple months. I ended up using industrial strength velcro, which has not only kept the louver on for almost 2 years, but which also allows you to remove the louver to clean the window. ua-cam.com/video/GCpWael4PDc/v-deo.html

Thank you

Can I apply the adhesive promoter on the 3m tape instead of the glass