- 95
- 280 516
RSM Stuff
United States
Приєднався 11 жов 2020
Just a guy with his toys and hobbies.
Plow Update
It has been a while since I have been able to make a video. The plow is coming along just need some more time at home to be able to get it finished. I am planning on being home in a few weeks to get some more content together.
Переглядів: 212
Відео
Max Pump Pressure on My 3025D
Переглядів 2478 місяців тому
Using a Bluetooth pressure transducer from Transducers Direct, model info below. At idle it was at 2583psi and 2630psi at full throttle. Now since pressure is a created by restricting fluid flow, I wonder what the pressure will be in the summertime when the oil flows easier than in the winter. I will check it again this summer or after I have been working the tractor for a few continuous hours ...
Issues with the Tiller, shearing bolts and grass build up.
Переглядів 22111 місяців тому
With using this tiller some of the issues I am having is tines breaking bolts that I think is from hitting stones. Another issue is with all of the grass that has been tilled it keeps making rows the grass clods will lift the tiller and not allow it to till as deep as I would like. Not to mention all of the bailing twine that gets picked up, on the plus side the field is getting cleaned up.
Did What I Didn't Want To Do
Переглядів 879Рік тому
I purchased a 6' tiller because I couldn't rent one. This tractor hasn't had an issue pulling it. I normally pull it in 1st or 2nd gear low range. Worked this area in a few hours and I am happy with the results. The only complain at this point is the big field stones that could cause issues in the future, but so far so good right now.
Plow back together and pulling the disc out of the weeds.
Переглядів 286Рік тому
Put the plow back together and finished what I started in the hay field. Pulled the old disc out of the weeds and started using it to try to get this part knocked down.
Another day with things breaking!!!!
Переглядів 414Рік тому
Well I thought it would be a good idea to get part of this hay field useable since part of it hasn't been cut in years. Did not expect the plow to break on me. I almost got the tractor stuck but thankfully got it out.
Making another food plot/Go Pro survived Again
Переглядів 338Рік тому
Been a while since I have been able to make a video. I’m making another food plot. Pulling some small trees out with the 3025D for some shooting lanes and the disc does a lot better with some extra weight.
John Deere 3025D is repaired, easy fix
Переглядів 623Рік тому
The noise I was hearing was the front axle moving forward and backwards. The dealer took the end play out and no more noise. I guess the sound was easy to hear on the left side of the tractor.
B oil system and 3025D update; I may have broke it!!!
Переглядів 385Рік тому
The oil system is pulled from the B and I have take the 3025D to the dealer to find out if the issue I am having is covered under warrenty. The block is back from the machine shop and waiting on the crank and rods. Now I need to get the case and oil system parts cleaned so I can start reassembling the engine on the B. Once I hear back from JD on the D i will update you on what was found and if ...
1951 John Deere B cam Removal
Переглядів 595Рік тому
Removing the cam so it can be sent out to be reground. I did not use scotch write to clean the block. It was 000 steel wool, my bad. The block and crank are going to be machined and hopefully done in the next month. Next I will get the lubrication system removed and everything cleaned up.
1951 John Deere B crank Removal
Переглядів 726Рік тому
Finally got the crank removed. Now to get it to the machine shop and get it turned. Hopefully I will find out how the block is and if it is worth using.
1951 John Deere B Driver Disc/Belt Pulley Removal
Переглядів 1,7 тис.Рік тому
Sorry it has been a while since posting a video. This one is how to remove the clutch driver disc and the belt pulley. I am planning on doing shorter videos so people do not have to dig so much to find information. I still haven't heard anything back on the block. Fingers crossed it is still good to use.
John Deere 3025D with $40 Snow Plow
Переглядів 3,6 тис.Рік тому
Trying out the 7'6" snow plow that i have made fit on my 3025D. I still need to purchase some cylinders for the power angle and some shoes so I don't dig everything up. It seems to work and if we get some heavy snow I will be sure to try it out on that.
'51 John Deere B, This is Getting Expensive
Переглядів 999Рік тому
Well, where to start. Water in cylinder 2 when pulling the head off. Now I'm tearing the block off to have it checked for cracks and then hopefully boring it over. Now I need to pull the crank out and have it turned. I'm already this deep I might as well do it all.The bad thing is this was not my plan, but I want to make sure this is going to last for another 70 years.
'48 B Down to the Block, Rebuilt - I Don't Think So!!
Переглядів 1,2 тис.Рік тому
Removed the frame from the '48 B. There is a heavy ridge in the cylinders. I was told that this engine was rebuilt and had low hours. I guess someones idea of a rebuild is not the same as mine.
Is 25hp Enough to Pull a Square Baler
Переглядів 18 тис.2 роки тому
Is 25hp Enough to Pull a Square Baler
3rd Function Valve Failure and Troubleshooting
Переглядів 5 тис.2 роки тому
3rd Function Valve Failure and Troubleshooting
Parts List for 3rd Function Valve on my 3025D
Переглядів 2742 роки тому
Parts List for 3rd Function Valve on my 3025D
Thanks for the information. Mine started acting erratic then started to auto close. It is clearly under load like one of the coils is stuck on. Thought it might be moisture since we just got a lot af rain. One of the buttons feels different compared to the other which is the button that is auto closing, bitton was very sensitive. Checked continuity on both micro switches and they are good. One of the coils has continuity and the other one doesn't seem to have continuity, but its tough to get to upside down. Switched coil plugs and the bottom is now staying engaged, but still Auto closing. Im going to double check control plugs and wire splices for moisture before taking the solenoid valve apart to check for clogs, debris or anything strange., That may be causing power to stay engaged. At least now, I know what I'm looking for because of your video. So thanks. 🙏
I think I've narrowed it down to a faulty micro switch. Continuity readings were getting erratic until the point it just wouldn't give me a constant reading compared to the other one. Summit 3rd function kit is just under 2 yrs old.
I just bought one today 😊
@@c3homeimprovementllc927 I hope you enjoy it, I still like mine. Only if I was home more to use it. I’m hoping to be home in a few weeks to create some more videos.
I also used a 3-finger puller and that also worked
35 years ago i spent weeks wailing hay with a 28 hp tractor the rocking from the plunger is almost enough to put a 10 year old kid to sleep.
what tripod are you using and would you recommend that tripod?
It is an ion from wal-mart. I think for the price ($20-$30) it isn’t bad, light weight and easy to pack around. The price may have changed some since I purchased that one.
I’m in the process of buying this tractor. My only concern is how to run a wood chipper and a PTO generator when off the seat?
I am not going to say you can or can’t bypass the seat switch. Like any safety that is bypassed the owner of the equipment would take full responsibility for anything that happened.
That’s what I thought. Btw I’m learning a lot with your videos thanks a lot for all the tips you put out there.
@@CarlosRomero-tp8wv thanks for the feedback. I will try to make some more once work slows down a little. Been on the road a lot and haven’t had time to create any recently.
Had my 3025d for several years. And it has done many little jobs over the years. I have alll the tires filled with fluid and wheel weights all the way around. Last time checked drive on scale, it read 8,941 lbs. So no little car haul trailer is going to carry it so easy. But with weight this little tractor can easily carry a round bale. It can also pull a small 3 bottom plow. Breaking ground a 2 bottom is doable.
Nothing Nothing Nothing on old tractors, especially green ones is even remotely cost effective.
Thank you for sharing this, gonna make my life a little easier.
I have a 3025D as well, but my manual says to change oil at 400 hours. On page 35, it only tells me to check levels and add if needed. I called the dealer and asked them, they confirmed the first oil change wasn't due until 400 hours. My tractor is now 2 years old, but it only has 50 hours on it. Maybe I need to go ahead and change it? I find it odd that my operating manual would be different from yours. I certainly didn't expect the dealer to agree with 400 hours.
Im just going to go by this. www.deere.com/assets/pdfs/common/qrg/3d-series-north-america-edition.pdf
With my experience with oil it should be engine hours or time. Once the oil is exposed to oxygen then it starts to degrade, the additives can deplete over time and make the oil not the same as it was originally. I would rather change it early for a cost on my end vs the oil loosing some of its properties and causing extra wear on my engine.
What speed do you think you were travelling ?
To be honest I don’t know. I can try to get a speed when I’m home again.
Dont worry about it. I thought you may be travelling around 3.5 mph, thats all, thanks @@rsmstuff3178
3-3.5mph is how fast I was going.
@@rsmstuff3178 thanks for your reply, mighty little tractor there !
Great video budd
Great video budd 😊😊
Beautiful
Thanks! Mine auto opens. It was sure nice seeing the inside parts of the valve and now I know what is in there.
if you run a jd B with a baler, you can run the 3025D with the baler,I like my 3025D, good investment .I just wish it had live PTO.
i plowed with thim back in late 50s three 14 with the 420 43o 1010 have 430 and 1010 s and have a 314 plow retire farmed
Looking good so far!
Thank you
Great videos. Wondering if you have any regrets at all choosing a gear drive vs HST? Now that you have used it a ton. Would you stay with gear drive ?
I still like the gear drive. I have probably done more than I should with the tractor and I don’t know that the HST would be able to do the same. If I was going to be doing mainly loader work I could see where the HST would be a plus.
Thanks. Someone locally has a 3043 D for sale with really low hours…so I was considering.
Hey RSM. I have a 3025D and ordered a grapple. It will have 1/2 Ag fittings. I subscribed and learn all I can from you. I guess I'm ordering a Universal kit from Summit. I plan on getting hyd hoses built at local NAPA. I',m confused if i need fittings along with my kit. Did you take fittings from Summit kit to JD shop and they added them to your kit fittings. thats if you could help me drama.
I ordered the fittings and JD put the correct fitting on the hoses to match the fittings that came with the kit (installed on the valve block).
Looks like your tires wet
Wats that peace that runs from of baler to back on top
I think it is for a kicker attachment to throw the bales onto a wagon.
@@rsmstuff3178 that makes sense ..I just had never seen that around the Bristol Tn area
Thick hay lol
3rd gear high range you are just invited shit to break slow down
should have used a mold board plow and then a disc, you got too much residue
I'm sorry but did you not know that you use a 1/2" drive extension? Have you never had to remove a square plug? Good grief.
did this void your warranty? thanks
I don’t know, nothing was said about that when I was at the dealer getting hoses made. I had also taken the tractor back for a noise that I was having and it was repaired at no cost. It was the front axle moving in the bushings.
25 horse power can do a lot at least on flat ground I would not think about trying it on a hill
I can agree with that. Thankfully for me it is pretty flat where I’m at.
Where’s part 2?
I still have it tore apart. Time has not been my friend since I took this traveling job.
I found this exact same plow and I’m thinking of doing the same thing, I hope I can find parts for it.
Parts can be found but you have to do some digging for them.
It must be a universal thing for wives to hate the John Deere Place. However she went there without me and spent $5000.
Now you need a drag harrow or drag mat to smooth everything out.
Get a heat reflective cheap pair(less than $10) and put those under these in your boot. Thatll probably work well. It already made a huge difference without heated insoles for me working construction on slab floors in winter 10 hrs a day
Don’t cut that piece, a good shop should be able to make you a short piece cheap
Does this have cat 1 or cat 2 pins, I found a ford 101 3bottom plow and I’m thinking I can do this with it, Ty for the video, big help
CAT 1 pins.
can’t the switch be disabled on the seat
Yes it can but there is a liability by doing so.
Too much harrow for compact tractor
I thought the Artic shield insulated over booties were snake oil and ignored them for along time till one day my feet froze for 10 hours straight. I ordered the artic shields before I was out of the stand. Lemme tell you I'm a true believer. Idk what material those are made from but they immediately warm my feet up and keep them that way all day.
How did the two bottom plow you were working on turn out? I know it has been awhile since the original video but was just curious.
I have more parts painted. Just haven’t had that much time with traveling for work.
Back in my roofing days ,my toes would freeze. Putting a plastic sandwich bag over the toe area in between 2 pairs of socks actually worked. No more toe freezing.
Love when people do reviews of products they haven't even opened yet . What a waste of time .
Know this is a year old, but that implement in this part of the country is known as a spring tooth harrow.
That’s supposed to be 35 hp
I am wondering what the lift capacity would be without the bale on the back. I am buying a 3032E that has beet juice in the rear tires, which, of course will help.
I have beet juice in my rear tires. The lift capacity will not change with the ballast. The loader will only lift what it can. The bale on the back is to increase stability,and give more traction on the rear tires. The front axle kind of being a pivot point. The more you have on the rear the better and if you had wheel weights that would help more.
very detail review..👍.. thanks for your time, i just bought the snow deer heated sock, and i'm thinking of your product too, i'll try it when it arrive .. 👍.. thank you much Sir
You did a great job the JD b is nice to work on
Great video! I'm just about to pull the trigger on the 3025D... any regrets or problems you've had with it?
The only 2 things that I have had is: 1- the manual throttle pedal coming off ( I have a video on what I did to fix that) and 2- the play in the front axle bushing (there is an adjustment bolt for it) are the only problems I have had with the tractor. The only other problem was the third function valve sticking. Sometimes I would like more power, then I remember that this tractor will do really anything I need, the only thing more power gets you is to do work faster. I like just having an EGR valve for emissions. This is the KIS tractor to me (Keeping It Simple).
@@rsmstuff3178 Thank you for your quick reply and for your videos... they have been very helpful. Much appreciated!!
Well that sucks…& it certainly helped me. Thanks.
Thank you.
Mine won’t lift sh*t I love the 3025d otherwise
Well that stinks.
@@rsmstuff3178 I do like the rest of the tractor a lot it’s an animal with ice pick chains and a winch
@@Cat3406e I wonder what the pressure is at the hydraulic pump. I guess I need to do a video on that. If the pump pressure is not correct then you won’t be able to lift anything. When I get home this weekend I will see what it takes to get the tools to check it.